Toyota TUNDRA 2008 User manual

CIIT0590
Customization
Installation Instructions
August 29, 200
8
Title:
NAVIGATION INSTALLATION MANUAL
With Bluetooth Instructions (Tundra)
Models:
2008 Toyota Tundra

&1,07113(Q
TABLE OF CONTENTS
63 ~ 6413. TROUBLESHOOTING HINTS
61 ~ 6212. RE-INITIALIZING
166. CAR-NAVI PARTS DESCRIPTION
65 ~ 6914. DIAGNOSTIC CHART
6011. RE-INSTALLATION
155. INSTALLATION OUTLINE
17 ~ 29
7. DISASSEMBLY
BASIC
BLUETOOTH/VOICE RECOGNITION
REAR CAMERA
30 ~ 47
8. INSTALLATION
BASIC
BLUETOOTH/VOICE RECOGNITION
REAR CAMERA
48 ~ 509. GPS ANTENNA INSTALLATION
51 ~ 59
10. OPERATION CHECK
DISPLAY CHECK MODE
NAVIGATION CHECK MODE
BLUETOOTH CHECK
VOICE RECOGNITION CHECK
AUX PORT
REAR CAMERA
144. RECOMMENDED TOOLS
8 ~ 13
3. INSTALLATION PREPARATION
–CHART: FM1, FM2 AND AM PRE-SET STATIONS
4 ~ 72. PRECAUTIONS FOR INSTALLATION
31. DEFINITION OF TERMS
Page No.

3
&1,07113(Q
1. DEFINITION OF TERMS
WARNING: Describes precautions that should be
observed, in order to prevent injury or
death to the user during installation.
CAUTION: Describes precautions that should be
observed, in order to prevent damage
to the vehicle or its components,
which may occur during installation if
insufficient care is taken.
NOTE: Provides additional information that
facilitates installation work.
FRONT, REAR, LEFT, RIGHT: Provides additional information
that facilitates installation work.
TOOLS: Specifies the tools and equipment
recommended for this process.
ESD: Contains parts and assemblies
susceptible to damage by
Electrostatic Discharge (ESD).
To prevent unnecessary
troubleshooting, after an installation
procedure.

4
&1,07113(Q
1. Contents given in the WARNING and CAUTION in this manual must be
carefully followed during the installation. If they are ignored, functions
of the CAR-NAVI system are hindered, as well as personal injury or
damage to the vehicle may result. Always carry out the installation in
accordance with the WARNING and CAUTION as noted.
2. When the vehicle parts are removed, keep the tapping screws, bolts and
nuts organized so that the re-assembly will proceed correctly.
3. Do NOT remove vehicle parts except for those that are specified in this
manual.
4. Not all digital photographs depicted in this Installation Manual, will
reflect the current model and model year vehicle.
2. PRECAUTIONS FOR INSTALLATION
Failure to carry out these
procedures, will result in a possible
deployment of airbag(s), personal
injuries, or unnecessary repairs to
the Supplemental Restraint System
(SRS).
Turn the key switch to the LOCK
position. Next, remove the key from
the ignition switch.
WARNING
Do NOT work on the vehicle
while the battery’s NEGATIVE
terminal is connected. Working
on the vehicle with the battery
connected, may result in a short
circuit during the CAR-NAVI KIT
installation.
CAUTION
BATTERY
BATTERY
NEGATIVE
NEGATIVE
TERMINAL
TERMINAL
FRONT
Tools: 10mm Wrench
LOCK &
LOCK &
REMOVE!
REMOVE!

5
&1,07113(Q
Take care NOT to scratch any part of
the vehicle. Bind the tips of tools (i.e.:
clip remover, slot screwdriver, etc.)
with a piece of vinyl tape to prevent
damage to parts of the vehicle.
Cut away the excess part of all cable
ties, after fastening it.
NOTE
VINYL
VINYL
TAPE
TAPE
GOOD!
GOOD!
NOTE
Never use a voltmeter to
troubleshoot any of the harnesses
or connectors to the SRS.
Accidentally probing the
connectors to the SRS can lead to
deployment of the airbag.
SRS wire harness loom or cover is in
bright yellow colour.
WARNING
2. PRECAUTIONS FOR INSTALLATION

6
&1,07113(Q
Ensure that the run-wire is properly in
place of the RUN-WIRE SECTION, as
shown on the photo on the left. Always
fold the BASE over to meet the RUN-
WIRE SECTION, shown with the
yellow arrow. Use ordinary pliers to
squeeze the base and run-wire
section, until the latch locks.
NOTE
Carefully handle all connectors. Firmly
attach the connectors during
installation. The connector should click
shut.
Detach locking connectors by first
releasing the lock and pulling only on
the connector itself.
NOTE
CONNECTOR
CONNECTOR
2. PRECAUTIONS FOR INSTALLATION
RUN
RUN- -WIRE WIRE
SECTION
SECTION RUN
RUN- -
WIRE
WIRE
BASE
BASE
FENDER
FENDER
COVER
COVER
Use protective covers to avoid damage
and scratches to the vehicle
components.
•Seat cover
•Fender cover (photo)
•Floor cover
NOTE

7
&1,07113(Q
All connector views in this installation
manual, are viewed from the front side.
NOTE
CONNECTOR VIEWS
CONNECTOR VIEWS
2. PRECAUTIONS FOR INSTALLATION
K1
K1
(Front View)
K2
K2
K3
K3

8
&1,07113(Q
Before proceeding with the CAR-
NAVI kit installation, please remove
any audio CD(s) from the factory
radio assembly. Also, please
ensure that the pre-set radio
stations (FM1, FM2 and AM) are
written down to pre-set the AVN-S
display unit. Please use chart
below.
NOTE
CHART: FM1, FM2 AND AM PRE-SET STATIONS
AM
FM2
FM1
654321
3. INSTALLATION PREPARATION
• Prior to installing the CAR-NAVI System kit, check the following for damage or
malfunction:
• Internal and external trim and body work.
• Following vehicle functions:
• Radio (FM1, FM2, AM)
• Automatic Climate Control System (i.e.: AUTO, A/C, TEMP, FAN
SPEED CONTROL, ALL VENT MODES, REAR DEFROST,
SECURITY, HAZARD LIGHTS, etc.).
• CAR-NAVI system parts preparation:
• When unpacking the CAR-NAVI system kit, lay out all components in the
order of installation and check for missing or damaged parts.

9
&1,07113(Q
Please order the appropriate Stereo
Component Amplifier from the Toyota
Parts Department. This part is NOT
included in the Car Navigation Kit.
NOTE
Please order the Audio Upgrade W/H
from the Toyota Parts Department.
This part is NOT included in the Car
Navigation Kit.
NOTE
AUDIO UPGRADE WIRE
AUDIO UPGRADE WIRE
HARNESS
HARNESS
STEREO COMPONENT
STEREO COMPONENT
AMPLIFIER
AMPLIFIER
Please order the Bracket kit from the
Toyota Parts Department. This part is
NOT included in the Car Navigation
Kit.
NOTE
BRACKET
BRACKET
KIT
KIT
3. INSTALLATION PREPARATION: Basic Installation

10
&1,07113(Q
Please order the AUX & Steering SW
Wire Harness, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
AUX &
AUX &
STEERING
STEERING
SW W/H
SW W/H
Please order the most recent version
of Map DVD, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
MAP DVD
MAP DVD
Please order the Shielded Wire
Harness, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
SHIELDED WIRE
SHIELDED WIRE
HARNESS
HARNESS
3. INSTALLATION PREPARATION: Basic Installation

11
&1,07113(Q
Please order the AUX Fix Adapter,
from the Toyota Parts Department.
This part is NOT included in the Car
Navigation Kit.
NOTE
AUX FIX
AUX FIX
ADAPTER
ADAPTER
3. INSTALLATION PREPARATION: Basic Installation
Please order the appropriate
Navigation Brackets #1 and #2, from
the Toyota Parts Department. This
part is NOT included in the Car
Navigation kit.
NOTE
NAVIGATION BRACKETS
NAVIGATION BRACKETS
#1 AND #2
#1 AND #2

12
&1,07113(Q
Please order the Talk Switch Wire
Harness, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
TALK SWITCH WIRE
TALK SWITCH WIRE
HARNESS
HARNESS
3. INSTALLATION PREPARATION: Bluetooth/Voice Recognition
Please order the appropriate
Microphone Amplifier Assembly (MIC)
from the Toyota Parts Department.
This part is NOT included in the Car
Navigation Kit.
NOTE
Please order the MIC+Talk Switch
Wire Harness from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
MIC+TALK SWITCH
MIC+TALK SWITCH
WIRE HARNESS
WIRE HARNESS

13
&1,07113(Q
Please order the Camera kit from the
Toyota Parts Department. This part is
NOT included in the Car Navigation
Kit.
NOTE
3. INSTALLATION PREPARATION: Rear Camera
Please order the Camera Adapter
Wire Harness from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
CAMERA ADAPTER
CAMERA ADAPTER
WIRE HARNESS
WIRE HARNESS

14
&1,07113(Q
4. RECOMMENDED TOOLS
#10 Drill Bit
10mm Wrench
11mm or 7/16” socket (¼”)
Side Cutters
Pliers
2007~ Toyota Tundra: Electrical Wiring Diagram
Nylon Removal Tool
2007~ Toyota Tundra Repair Manual
Long and Short Tip Screwdriver
(Philips Type)
Comments:Manuals:
Comments:Installation Tools:
Ratchet ¼” Drive
8mm socket (¼”)
10mm socket (¼”) > Standard&Deep
4.0 N•m, 41kgf•cm, 36lbf•inTorque Wrench ¼” Drive
Ratchet 3/8” Drive
10mm socket (3/8”)
6” Extension (3/8”)
Vinyl Tape
Drill (Electric/Pneumatic)
Seat Covers
Fender Covers
Floor Protectors
Safety Goggles
Comments:Safety Tools:

15
&1,07113(Q
5. INSTALLATION OUTLINE
INTERIOR VIEW
AVN
AVN- -S S
DISPLAY UNIT
DISPLAY UNIT
GPS
GPS
ANTENNA
ANTENNA
AUX PORT
AUX PORT
STEREO
STEREO
COMPONENT
COMPONENT
AMPLIFIER
AMPLIFIER
AUDIO
AUDIO
UPGRADE W/H
UPGRADE W/H
TALK SWITCH
TALK SWITCH
(OPTION)
(OPTION)
MICROPHONE
MICROPHONE
(OPTION)
(OPTION)
EXTERIOR VIEW
REAR
REAR
CAMERA
CAMERA
(OPTION)
(OPTION)

16
&1,07113(Q
6. CAR-NAVI PARTS DESCRIPTION
3Cable Tie (7.5”)6
2
Trim Screws (#10-16
u
5/8”)
11
1Owner’s Manual (English and
French)
12
1Double Coated Tape10
10Foam9
1Push Pin (STT)8
10Cable Tie (4”)7
4Cable Tie (11”)5
1GPS Antenna Bracket3
15 Pin Wire Harness4
108663-00340GPS Antenna2
186120-06390AVN-S Display Unit1
Q’tyTOYOTA Part No.Part NameNo.
12
5
3
9
ELECTRO
ELECTRO- -
TAP
TAP™ ™
6
10
12
11
NOTE: NOT ALL COMPONENTS WILL BE USED FOR THE INSTALLATION METHOD.
LENGTH SHORT
8
4
7

17
&1,07113(Q
Do NOT work on the vehicle
while the battery’s NEGATIVE
terminal is connected. Working
on the vehicle with the battery
connected, may result in a short
circuit during the CAR-NAVI KIT
installation.
CAUTION
BATTERY
BATTERY
NEGATIVE
NEGATIVE
TERMINAL
TERMINAL
FRONT
Tools: 10mm Wrench
Temporary removal of part(s):
•Front Scuff Plate (RH)
FRONT SCUFF
FRONT SCUFF
PLATE (RH)
PLATE (RH)
Temporary removal of part(s):
Remove the NUT CLIP.
•Kick Panel (RH)
NUT
NUT
CLIP
CLIP
FRONT
KICK PANEL
KICK PANEL
(RH)
(RH)
7. DISASSEMBLY: Basic

18
&1,07113(Q
Temporary removal of part(s):
•Instrument Side Panel (RH)
Tools: Nylon Removal Tool
PANEL
PANEL
ASSEMBLY
ASSEMBLY
(RH)
(RH)
LOWER
LOWER
INSTRUMENT
INSTRUMENT
SUB
SUB- -ASSEMBLY ASSEMBLY
Temporary removal of part(s):
•Screw (1)
Tools: Long Tip Screwdriver (Philips
Type)
: SCREW
: SCREW × ×1 1
LOWER
LOWER
INSTRUMENT SUB
INSTRUMENT SUB- -
ASSEMBLY
ASSEMBLY
Temporary removal of part(s):
•Bolt (1)
Tools: Ratchet ¼” Drive, 10mm socket
(¼”)
: BOLT
: BOLT × ×1 1
LOWER
LOWER
INSTRUMENT SUB
INSTRUMENT SUB- -
ASSEMBLY
ASSEMBLY
7. DISASSEMBLY: Basic

19
&1,07113(Q
Place the glove box to the open
position, as indicated on the photo.
Temporary removal of part(s):
•Screws (2)
•Lower Instrument Sub-Assembly
Tools: Short Tip Screwdriver (Philips
Type
: SCREW
: SCREW × ×2 2
LOWER
LOWER
INSTRUMENT SUB
INSTRUMENT SUB- -
ASSEMBLY
ASSEMBLY
<<Floor Shift>>:
Temporary removal of part(s):
•Cup Holder
•Upper Console Panel
<<Floor Shift>>:
Temporary removal of part(s):
•Center Lower Instrument Panel
•Connectors
CUP HOLDER
CUP HOLDER
SHIFT KNOB
SHIFT KNOB
UPPER
UPPER
CONSOLE
CONSOLE
PANEL
PANEL
CENTER LOWER
CENTER LOWER
INSTRUMENT
INSTRUMENT
PANEL
PANEL
7. DISASSEMBLY: Basic

20
&1,07113(Q
Tools: Short Tip Screwdriver (Philips
Type
: CLIP
: CLIP × ×1 1
CENTER LOWER
CENTER LOWER
COVER
COVER
<<Column Shift>>:
Temporary removal of part(s):
•Clip (1) – RH
•Center Lower Cover
<<Column Shift>>:
Loosen the following part(s):
•Lower Instrument Panel
CUP HOLDER
CUP HOLDER
SHIFT KNOB
SHIFT KNOB
UPPER
UPPER
CONSOLE
CONSOLE
PANEL
PANEL
CENTER LOWER
CENTER LOWER
INSTRUMENT
INSTRUMENT
PANEL
PANEL
<<Column Shift>>:
Temporary removal of part(s):
•Clip (1) - LH
CENTER LOWER
CENTER LOWER
COVER
COVER
Tools: Short Tip Screwdriver (Philips
Type
: CLIP
: CLIP × ×1 1
LOWER
LOWER
INSTRUMENT
INSTRUMENT
PANEL
PANEL
7. DISASSEMBLY: Basic