Toyotomi Zibro LC-140 User manual

LC – 140
GB OPERATING MANUAL ............................. PAGE 2
D GEBRAUCHSANWEISUNG............................PAGE 18
F MANUAL D’UTILISATION ........................... PAGE 36
NL GEBRUIKSAANWIJZING .............................PAGE 54
E INSTRUCCIONES DE USO ............................PAGE 70
I ISTRUZIONI D’USO .................................PAGE 86
DK BRUGERVEJLEDNING ...............................PAGE 102
N BRUKERINSTRUKSEN ...............................PAGE 118
S INSTRUKTIONERNA INNAN ANVANDNING..............PAGE 134
FIN KäyTTöOHJEET ...................................PAGE 150

Thank you for choosing a “TOYOTOMI” product!
Toyotomi products are used by satisfied customers worldwide. In order to
assure the comfortable and safe use of our products by customers in each
country, our products conform to the safety standards not only in Japan but
also in every country around the world we do business with.
Toyotomi tailors its products to satisfy its customer’s needs by always pursuing
our business philosophy, “sharing joys in daily living”. We will continue to
research, develop and manufacture products that match people’s lifestyle for
efficiency, safety and comfort.
We hope that you’ll enjoy your Toyotomi appliance for years to come!
We invite you to read this instruction manual first, to ensure the maximum
lifetime for this appliance.
Get to know us better…visit us at www.toyotomi.eu for our full line of
products.
1 READ THE DIRECTIONS FOR USE FIRST.
2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.
3 BEFORE YOU START READING, CONSULT THE MAIN COMPONENTS LIST ON THE LAST PAGE.
4
2

GENERAL DIRECTIONS FOR USE
Below you will find the main steps to be taken for
using your heater. For more details, please refer to
the MANUAL.
Remove all packaging materials (Fig. A).
Fill the removable tank (refer to Section B, Fig. D).
Insert the plug into the wall-socket.
Ignite the heater using the key (refer to Section D).
If required, change the temperature using the adjustment keys
(refer to Section E).
Switch off the heater by pressing the key .
1
2
3
4
5
6
•As a fire precaution, the tank must be filled either when the heater has been
switched off or in another room than the room where the heater is installed.
•Always ensure that the tank is closed properly after filling it at a safe distance from
all sources of heat and open flames (see Section B).
•The first time the heater is ignited it will smell like “new” for a short time.
•Store all fuel containers with their original caps and seals in a cool and dark place.
•Fuel ages. Use new fuel at the start of every heating season.
•Only use high quality and water -free pure paraffin in accordance with local
legislation.
•Before changing brands and/or types of fuel make sure that the mobile heater first
completely empties all of the remaining fuel inside the heater.
4
3
1 READ THE DIRECTIONS FOR USE FIRST.
2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.
3 BEFORE YOU START READING, CONSULT THE MAIN COMPONENTS LIST ON THE LAST PAGE.

WHAT YOU NEED TO KNOW IN ADVANCE
ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION
Read this user manual carefully before using the appliance and keep it for future
reference. Install this device only when it complies with local/national legislation,
ordinances and standards. This product is intended to be used as a heater in
residential houses and is only suitable for use in dry locations, in normal household
conditions, indoors in living room, kitchen and garage.
Note: To avoid unexpected shut off, we recommend to put a door or window ajar
when the heater is operating.
Regardless of the model, you must always make sure that the heater is used in
a room large enough to enable the heater to be used safely without extra
ventilation. If the room is smaller than required, you must always open a door or
window slightly (ensuring an opening of approx. 2.5 cm). It is important that every
room where the heater is used has sufficient air intake and efficient air outflow
(both openings must have a minimum cross section of 50 cm2). No modifications
to the safety system are allowed, as that will invalidate the guarantee that the air
probe will work properly. Consult your dealer in case of doubt.
Especially for France: Your heater was designed to operate exclusively on fuel for
liquid fuel-operated mobile heaters in accordance with the Decrees of 18-07-2002
and 25-06-2010. The use of other fuels is forbidden. Ask your dealer or check our
website for the addresses of our retailers. The liquid fuel-operated mobile heater
is intended as an extra heater, and not as a continuous source of heat.
Especially for United Kingdom: Only use Class C1 paraffin fuel in accordance with
BS2869; Part 2, or equivalent.
The user must comply with the following instructions for proper use:
DO NOT
- use the liquid fuel-operated mobile heater in caravans, boats, and vehicle
cabins;
- use the liquid fuel-operated mobile heater in insufficiently ventilated rooms
(consult the table of properties for the minimum dimensions of the room to
be heated), underground rooms and / or at a height of over 1500 metres;
- modify the heater safety features.
The use of this type of heating in public rooms is subject to prior regulatory
permission. Obtain proper information on this in advance.
4
4

THE RIGHT FUEL
Your heater has been designed for use with high-quality water-free pure paraffin
oil. Only fuels of this kind will ensure clean and proper burning. Lower quality fuel
may result in:
increased possibility of malfunctioning
incomplete burning
reduced heater lifetime
smoke and/or smells
deposits on the grid or mantle
Using the right fuel is therefore essential for safe, efficient, and comfortable use
of your heater.
Damage and/or malfunctions of the heater due to the use of other than high
quality water-free pure paraffin oil is not covered by the warranty.
Always refer to your local dealer for the right fuel for your heater.
MANUAL
AINSTALLING THE HEATER
1Carefully remove your heater from the box and check the contents.
In addition to the heater you also need to have:
a manual fuel pump
 a transportation cap
 these directions for use
Keep the box and the packaging materials (Fig. A) for storage and/or
transportation.
2Open the lid of the removable tank and remove the piece of cardboard.
3Fill the removable tank as indicated in Section B.
4The floor should be firm and completely level. Reposition the heater, when it
is not level. Do not try to correct the situation by placing books or other
goods under the heater.
A
4
5
This transportation cap
is packed separately in
the box. Only this cap
ensures trouble-free
transportation of the
heater after use.
Store it well!
Only the use of the
correct fuel will ensure
safe, efficient, and
comfortable use of your
heater.

5Insert the plug into the wall-socket (230 Volts - AC / 50 Hz) and set the
correct time using the adjustment keys (refer to Section C).
6Your heater is now ready for use.
BFILLING FUEL
Fill the removable tank in a suitable place since there can always be some spillage.
Follow the procedure below:
1Make sure that the heater is switched off.
2Open the upper lid and lift the removable tank out of the heater (Fig. B).
Note: Some drops may leak from the tank. Put down the removable tank (cap
pointing upwards, handle on floor (Fig. C) and screw off the fuel cap.
3Fill the removable tank using a fuel pump (refer to fuel pump operation
instructions.) Make sure that it is in a higher position than the removable tank
(Fig. D). Insert the ribbed hose into the opening of the removable tank.
4Check the removable tank fuel gauge while filling the tank (Fig. E). Stop filling
once the gauge indicates that the tank is full. Never overfill the tank,
especially not when the fuel is very cold (fuel expands when it heats up).
5Check whether the fuel cap is straight and tightened properly. Reinstall the
removable tank in the heater (cap down). Close the lid.
CSETTING THE CLOCK
It is only possible to set the correct time and day, when the heater is connected to
the mains and not burning. Use the adjustment keys to set the time and day/set
(weektimer) to set the day.
First press one of the three keys to switch on the function (the 4-digit will start
blinking). Next, set the hours using the key (hour) and the minutes using the
key (min.) and the day using the key extension day/set .
Press once to increase the value by one step. When you hold down the key, the
value will continue going up, until you release the key again. After approximately
10 seconds the 4-digit will stop blinking and the setting will be locked (Fig.F).
5 minutes after switching off the heater, the information on the display will
disappear and the heater will automatically switch into the stand-by position.
When the heater has been unplugged for more than 30 minutes (or after a power
failure), the time and the day need to be set again.
4
6
F: When the 4-digit stops
blinking, the setting
has been locked to the
indicated value.
D
C
B
E
empty full
!

D IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Always ignite the heater with the button
 . Never use matches or a cigarette
lighter. Just press the button
 to ignite the heater.
The button will start blinking, indicating that the ignition procedure has started.
This will take a short while. Once the heater is burning, the button
 will
remain lit (red). The information display
 will show two numbers (Fig. G). The
actual room temperature is indicated below ROOM, while the temperature setting
is indicated below SET. The latter can be changed with the adjustment keys (refer
to Section E).
Prior to igniting the heater, always check for sufficient fuel in the removable tank.
ESETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted, when the heater is burning. Use
the adjustment keys to adjust the temperature. First press either of the two
keys to switch on the function (the °C mark and 4-digit will start blinking). Next,
adjust the temperature using the key (min.) to set the temperature to a higher
setting and the key (hour) to lower the temperature. Press once to increase the
value one step. After approximately 10 seconds the °C mark and 4-digit will stop
blinking and the setting will be locked (Fig. F).
The available temperature settings range from 6°C minimum to 28°C maximum.
When the heater has been unplugged for more than 10 minutes (or after a power
failure), the temperature will reset to the factory setting of 20°C.
FSWITCHING OFF THE HEATER
There are two ways to switch off the heater.
1Press the button . The information display will show the CLOCK signal.
Within approximately one minute the flame will have extinguished.
2Press the TIMER key , when you want to switch off the heater and ignite it
again with the timer the next time. This not only switches off the heater, but
it also activates the timer function.
GTHE INFORMATION DISPLAY
The information display  not only serves as an indicator of the (set) time and
temperature (Sections C, E, and F), it also indicates any malfunctioning of the
heater. The code on the information display tells you what is the matter:
CODE INFORMATION WHAT TO DO
e - 0 Temperature within the heater too high. Cool-down and re-ignite.
f - 0 Power interrupted. Re-ignite the heater.
e - 1 Faulty thermostat. Contact your dealer.
f - 1 Faulty burner thermistor. Contact your dealer.
e - 2 Starting problems. Contact your dealer.
e - 5 Tipping-over protection. Re-ignite the heater.
e - 6 Poor burning. Contact your dealer.
e - 7 Room temperature If necessary,
above 32°C. re-ignite the heater. 4
7
G: The required
temperature on the
left, the measured
temperature on the right.
In case of any
malfunctioning the
information display
will tell you what is the
matter.

e - 8 Defective booster. Contact your dealer.
e - 9 Air filter dirty; or Clean filter
Fuel pump dirty. Contact your dealer.
The heater has been in operation
continuously for a period of 69 hours
and has turned itself off automatically. Switch the heater back on.
-- : --
+
Out of fuel. Refill removable tank.
-- : -- + Too little ventilation. Ventilate better.
Always contact your dealer for any malfunctioning not listed above.
AUTOMATIC DEACTIVATION
This heater is fitted with a safety system that ensures that it switches off
automatically after 69 hours continuous operation. The following will then appear
in the display: . If desired, you can switch the heater on again by pressing
the button (see Section D).
AUTOMATIC CLEANING MODE
When the heater has been burning continuously for two hours at its highest
setting, the burner will automatically start an autoclean procedure. The display
will show the autocleaning code cl:05 running back to cl:01. The procedure takes 5
minutes, during which the heater will burn at its lowest setting, while the burner
autocleans. When the burner is clean again, the heater will automatically switch
back to the highest setting again.
HCHILDPROOF LOCK
The childproof lock can be used to prevent children accidentally changing the
heater settings. When the heater is burning and the childproof lock is on, the
heater can only be switched off. Other functions are blocked then. If the heater
has already been switched off, the childproof lock also prevents accidental ignition
of the heater. Activate the childproof lock by pressing the appropriate key

and holding it down for more than 3 seconds. The KEY-LOCK indicator ( ) will
appear on the information display (Fig. H), indicating that the childproof lock has
been activated. Switch off the childproof lock by pressing the key
 and holding it
down for more than 3 seconds once again.
4
8
H: When the mark
appears, the childproof
lock has been activated.

ITHE CORRECT USE OF ‘SAVE’
The ‘SAVE’ function allows you to limit the temperature. When this function is
activated, the heater will automatically switch off, when the room temperature
exceeds the set temperature by 3°C. Subsequently, when the room temperature
has dropped again to the set temperature, the heater will automatically switch on
again.
Activate the ‘SAVE’ setting by pressing the appropriate key. will display on
the information display (Fig. I). Switch off the function by pressing the SAVE key
once again.
Without the ‘SAVE’ setting your heater will maintain the set temperature by
approximation as well, by adjusting its heating capacity. ‘SAVE’ is an economy
setting, which you can use when, for instance, you are not present in the room or
to keep it frost-free.
JTHE ‘FUEL’ INDICATOR
When the FUEL indicator appears, it means that there is only fuel left for 10
more minutes. The count-down of the remaining heating time can be seen in the
information display (Fig. J). Now you have two options:
You remove the fuel tank and refill it outside the living room (section B) or
You push the button extension . By pushing this button, the remaining
heating time will extend to 90 minutes.
The heater will automatically switch back to its lowest position. In the display
the number 90 will appear, which will decline to 10. At the arrival of 10,
you will hear an alarm signal every two minutes, warning you to refill the
removable tank. If you do not react, the heater will extinguish by itself. The
heater will also sound a warning signal, when it switches off. The fuel
indicator will blink, while four lines (--:--) are blinking in the information
display. You can stop this by pressing the button once more.
Once the heater has used up all its fuel and extinguished, it will take some time,
after the refill, before the heater is completely ready for use again.
KTHE ‘VENT’ INDICATOR
When the VENT indicator starts blinking, this is a sign that the room is not vented
sufficiently (Fig. K). The heater will switch off automatically. If the indicator continues
blinking after extra ventilation, please contact your dealer.
4
9
I: When the SAVE
function is activated, the
heater will automatically
switch on or off in
order to remain within
a specified temperature
range.
J: When the FUEL
indicator has appeard,
the information display
will show the number of
minutes of fuel left in
the tank.
K: A blinking VENT
indicator light is a sign
that you need extra
ventilation.
!

LMAINTENANCE
Switch off the heater and let it cool down, before you start any maintenance
work. Also disconnect the plug from the mains. Your heater needs hardly any
maintenance. It is, however, important that you clean the air filter and the
vent filter with a vacuum cleaner and the grid with a damp cloth, both on a
weekly basis. Remove the air filter cap occasionally (Fig. L) and clean it with soapy
water. Prior to reinstallation, make sure that the air filter cap has fully dried.
Regularly inspect the fuel filter as well:
1Remove the removable tank from the heater and remove the fuel filter
(Fig. M). Some drops may leak from the filter; keep a cloth at hand.
2Remove the dirt by tapping the fuel filter upside-down against a hard surface.
(Never clean it with water!)
3Reinstall the fuel filter into the heater.
We recommend that you remove dust and stains in time with a damp cloth,
because otherwise these may cause stains that are hard to remove.
Do not remove any heater components yourself. Always contact your dealer
for repairs. When the power cord is damaged, it may only be replaced by an
authorised fitter. Use a new cord of the type H05 VV-F.
MSTORAGE (END OF THE HEATING SEASON)
At the end of the heating season, you must store the heater in a dust-free place,
if possible in its original packaging. Unused fuel cannot be used in the next
heating season. We therefore recommend that you burn up all fuel. If there is
still some fuel left, do not throw it away, but dispose of it in accordance with the
local regulations for the disposal of domestic chemical waste. Always start the
new heating season with fresh fuel. When you start re-using the heater follow the
instructions again (starting from section A and as specified).
NTRANSPORTATION
Take the following measures to avoid fuel leakage during the transportation of
the heater:
1Let the heater cool down.
2Remove the removable tank from the heater and remove the fuel filter
(refer to Section L, Fig. M). Some drops may leak from the filter; keep a cloth
at hand. Store the fuel filter and the removable tank outside the heater.
3Place the transportation cap into the position of the fuel filter (Fig. N).
Press it tight. The transportation cap will, as much as possible, prevent oil
leakage from the heater during transport.
4Always move the heater in an upright position.
5Make the fixed tank empty with a fuel pump before transportation or in case
of wrong or dirty fuel. First remove the fuel filter and then insert the fuel
pump into the empty fixed tank. Follow the same procedure if the fuel tank
contains water.
4
10
Fuel filter
M
transportation
cap
N
L
!

OSPECIFICATIONS
Ignition electrical Dimensions (mm) width 435
Fuel paraffin (including base plate) depth 315
Capacity (kW) max. 4.00 height 437
Capacity (kW) min. 1.05 Accessories manual fuel pump
Suitable space (m3)** 65-170 transportation cap
Fuel consumption (l/hr)*0.417 Mains 230V
Fuel consumption (g/hr)*333 -- AC/50 Hz
Burning time per tank (hr)*18.2
Electrical consumption igniter 320 W
Capacity removable tank (litres) 7.6 continuous 24W
Weight (kg) 11.5 Fuse rating 250V, 5A
* At maximum setting ** Specified values are indicative
PWARRANTY PROVISIONS
Your heater comes with a 48-month warranty starting on the date of purchase.
Within this period all defects in material or workmanship will be repaired without
any charge. The following provisions shall apply regarding this warranty:
1We expressly dismiss all other claims for damages, including consequential
damages.
2Any repairs or replacements of components within the term of warranty will
not result in an extension of the term of warranty.
3The warranty shall no longer apply, when the heater has been modified,
non-original parts have been used, or when it is repaired by third parties.
4The warranty shall not apply to parts that are subject to normal wear, such as
the burner mat, any kind of gasket and the manual fuel pump.
5The warranty shall only apply, when you present the original, dated proof of
purchase, provided no changes have been made to it.
6The warranty shall not apply to damages caused by actions not in compliance
with the Directions for Use, neglect, and the use of an incorrect type of fuel,
or fuel past its use-by date. The use of incorrect fuel can even be dangerous*.
7Transportation costs and the risks involved during the transportation of the
heater or heater components shall always be for the account of the purchaser.
In order to avoid unnecessary costs, we recommend that you always read the
’Directions for Use’ carefully first. In case they offer no solution, please take the
heater to your dealer for repair.
* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this
happen, never try to move the heater, but always switch off the heater immediately. In case of emergency you
may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher.
4
11

14 TIPS FOR SAFE USE
1Children should be supervised to ensure that they do not play with the
appliance.
2Do not move the heater when it is burning or still hot. Do not refill nor
service the heater when it is burning or still hot.
3Position the front of the heater at a distance of minimum 1.5 metres from
walls, curtains, and furniture.
4Do not use the heater in dusty rooms. You will not have optimum burning
in such rooms. Do not use the heater in the immediate surrounding of a
bath, a shower or a swimmingpool.
5Switch off the heater, before you leave or go sleeping. Unplug the
heater as well, when you go away for a longer period of time
(e.g. holidays).
6Store and move fuel only in suitable tanks and jerrycans.
7Make sure that the fuel is not exposed to heat or extreme temperature
changes. Always store the fuel in a cool, dry and dark place (sunlight
will affect the quality).
8Never use the heater in places where harmful gasses or fumes may be
present (e.g. exhaust gasses or paint fumes).
9Beware that the grid of the heater becomes hot. If the appliance is
covered there is a risk of fire.
10 Always make sure that there is sufficient ventilation.
11 This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
12 This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack
of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved.
13 Children shall not play with the appliance.
14 Cleaning and user maintenance shall not be made by children without
supervision.
Defective electrical devices and batteries must be kept separate from household
waste. Ensure that there is effective recycling where possible. Ask you local council
or dealer for expert advice on recycling.
4
12

4
13
QWEEK TIMER
Here is an example on how the week timer can be programmed:
• Maximum of 3 programs per day can be set.
• Every day of the week can be programmed separately.
• Minimum switching interval, 1 hour.
• Minimum activation time, 1 hour.
• Choice between manual and timer
• Settings are saved in the memory and remain saved without power supply.
Monday Tuesday Wednesday Thursday Friday Saturday Sunday
P1 ON 6:30 6:30 6:30 6:30 6:30 10:00 9:00
P1 OFF 8:45 8:45 8:45 8:45 8:45 23:00 23:00
P2 ON 12:00 15:00 18:00 12:00 12:00
P2 OFF 14:00 23:00 23:00 14:00 14:00
P3 ON 18:00 18:00 18:00
P3 OFF 23:00 23:00 23:00
Make sure the heater is connected to the mains and not
burning. Press the timer-key . Also make sure the time
and day are set correctly. Choose the day you would like
to program by pressing the adjustment keys . Press the
adjustment key to increase the day by one step and press
the key to decrease the day.
Press extension/day/set to select the desired day. The
display shows:
With the adjustment keys and you can choose
between the programs P1, P2 and P3. You can also choose
the option Copy to copying the setting from one day to
another. Press extension/day/set to select the displayed
program.
Use the adjustment keys to set the hour at which the
heater must ignite. Press the adjusment key to increase the
hour and the key to decrease the hour. Press extension/
day/set to select the right hour.
PROGRAMMING THE WEEK TIMER



4
14
Then, use the adjustment keys to set the minute. Press the
adjustment key to increase the minute and the key to
decrease the minute. Press extension/day/set to select the
right minute.
Use the adjustment keys to set the hour at which the
heater must shutt off.
Press the adjusment key to increase the hour and the key
to decrease the hour.
Press extension/day/set to select the right hour.
Then, use the adjustment keys to set the minute. Press the
adjustment key to increase the minute and the key to
decrease the minute. Press extension/day/set to select the
right minute.
The settings for program 1 for Monday are programmed and
the display shows SET for 3 seconds.
After 3 seconds choose another day or end the setting mode
by pressing timer.
Press the “timer” key to exit the weekly timer setting mode and return to the time and a
day of the week display. Timer lamp turns off.
Use the copy function if there are multiple days during one week which should have the
same setting times.
Make sure that the heater is not burning. Press the timer key
. Use the adjustment keys until the day of its source is
displayed in the display.
Press extension/day/set to select.
The display shows:
COPYING THE SETTING FROM ONE DAY TO ANOTHER



4
15
Use the adjustment keys or to choose copy. Press
extension/day/set to select the copy function.
Use the adjustment keys or to select the day to which
the settings should be copied. Press extension/day/set to
choose the selected day.
The settings for program for Tuesday are programmed and
the display shows SET for 3 seconds.
After 3 seconds choose another day to copy or end the
setting mode by pressing timer.
Switch on the heater by pressing the POWER button . And then press the timer-key 
immediately after that. The Timer light will light up and the heater shuts off. The On / Off
indicators on the display shows whether the appliance is switched on or off.
When the appliance is switched off by the timer, the off
indicator is visible. The display shows the -actual time.
When the appliance is switched on by the timer, the on
indicator is visible. The display shows the desired (set) and
actual (room) temperature.
OPERATING THE WEEK TIMER



4
16


   












MAIN COMPONENTS
Front plate
Grid
Base plate
Lid for removable
tank
Operation panel
Handle
Removable tank
Air filter
Vent filter
Thermostat
Plug + cord
Information display
key
Childproof lock
Adjustment keys
(time and
temperature)
TIMER
SAVE key
Timer lamp
Extension / day / set
(weektimer)




















4
17

Vielen Dank für den Kauf des Marken-Heizofens von Toyotomi!
Der japanische Hersteller Toyotomi Co. Ltd. ist seit mehr als 65 Jahren
weltweiter Marktführer im Bereich mobiler Petroleumöfen. Toyotomi steht für
Service, Qualität und Garantie.
Auf der ganzen Welt nutzen zufriedene Kunden die komfortablen und sicheren
Heizöfen. Toyotomi-Produkte erfüllen einen sehr hohen Sicherheitsstandard,
sie erfüllen die Sicherheitsnormen nicht nur in Japan, sondern auch in allen
Ländern auf der Welt, in denen die Produkte verkauft werden.
Effizienz, Sicherheit und Komfort sind oberste Ziele bei Toyotomi.
Wir hoffen, dass Sie Ihr Toyotomi-Produkt viele Jahre geniessen können.
Bitte lesen Sie zunächst sorgfältig die Anleitung, um Ihr Gerät optimal
einzusetzen.
Informieren Sie sich auch über unsere anderen Produkten. Besuchen Sie uns
auf www.toyotomi.eu für unsere gesamte Produktlinie.
1 LESEN SIE ZUERST DIE BETRIEBSANLEITUNG.
2 WENDEN SIE SICH IM ZWEIFELSFALL AN IHREN HÄNDLER.
3
VOR DEM LESEN DER ANLEITUNG, KONSULTIEREN SIE DIE HAUPTKOMPONENTEN LISTE AUF DER LETZ-
TEN SEITE.
2
18

KURZANLEITUNG
Entfernen Sie das gesamte Verpackungsmaterial (Abb. A).
Befüllen Sie den Brennstofftank (siehe Kapitel B, Abb. D).
Stecken Sie den Stecker in die Steckdose.
Starten Sie den Heizofen über die -Taste 
(siehe Kapitel D).
Verändern Sie wenn nötig die gewünschte Temperatur
über die Einstelltasten (siehe Kapitel E).
Schalten Sie den Heizofen über die -Taste  aus.
1
2
3
4
5
6
•Zur Vorbeugung von Feuer muss entweder der Heizofen vor dem Füllen des
Brennstoffbehälters ausgeschaltet werden oder der Behälter muss in einem anderen
Raum als dem, in dem sich der Heizofen befindet, gefüllt werden.
• Sorgen Sie immer dafür, dass der Brennstoff-behälter nach dem Füllen gut
verschlossen ist. Achten Sie beim Füllen darauf, dass sich der Behälter in einer
sicheren Entfernung von Wärmequellen und offenen Flammen befindet (siehe
Kapitel B).
• DasersteMalwirdIhrHeizofenwährenddesBrennensnochkurz‘neu’riechen.
• LagernSiealleBrennstoffbehältermitOriginaldeckelundVersiegelungkühlund
dunkel.
• Brennstoffaltert.BeginnenSiejedeHeizsaisonmitneuemBrennstoff.
• VerwendenSienursauberesHeizpetroleuminÜbereinstimmung mitderlokalen
Gesetzgebung.
• Wenn Sie zwischen den einzelnen Sorten / Marken wechseln, müssen Sie den
Heizofen erst vollständig leer brennen lassen.
2
19
1 LESEN SIE ZUERST DIE BETRIEBSANLEITUNG.
2 WENDEN SIE SICH IM ZWEIFELSFALL AN IHREN HÄNDLER.

WICHTIG ZU WISSEN
JEDERZEIT AUSREICHEND LÜFTEN
LesenSiebittevorderAnwendungdesGerätssorgfältigdieBedienungsanleitung
undbewahrenSiesiefüreinezukünftigeEinsichtnahmeauf.DasGerätnur
dann installieren, wenn die örtlich geltenden bzw. nationalen Vorschriften,
VerordnungenundNormenerfülltsind.DiesesProduktistfürdenGebrauchals
Heizofen in Wohngebäuden bestimmt, und darf nur in trockener Umgebung,
unter normalen Haushaltsverhältnissen, in Wohnräumen, Küchen und in Garagen
verwendet werden.
Hinweis: Um ein unerwartetes Abschalten zu vermeiden, empfehlen wir, eine Tür
oder ein Fenster einen Spalt offen stehen zu lassen, wenn das Heizgerät in Betrieb
ist.
JedesModellbenötigteinebestimmteminimaleRaumgröße,umdenHeizofen
sicher, ohne zusätzliche Belüftung, betreiben zu können. Wenn der betreffende
RaumkleineralsderangegebeneMinimumwertist,dannmußdafürgesorgt
werden,daßimmereinFensterodereineTüreinenSpaltbreitoffenbleibt
(ca.2,5cm).Esistwichtig,dassjederRaum,indemderHeizofenbenutztwird,
ausreichend belüftet und gut entlüftet wird (beide Öffnungen müssen einen
Querschnitt von mindestens 50 cm2haben). Änderungen am Sicherheitssystem sind
unzulässigundwürdendieGarantieeinereinwandfreienFunktiondesLuftfühlers
nichtigmachen.WendenSiesichimZweifelsfallanIhrenHändler.
Speziell für Frankreich:IhrHeizofenwurdeausschließlichfürdenBetriebmit
BrennstofffürmitflüssigemBrennstoffbetriebenemobileHeizöfengemäßden
Richtlinienvom18.07.2002un25.06.2010ausgelegt.DieVerwendunganderer
Brennstoffeistverboten.FragenSieIhrenHändler.DieAdressenunsererHändler
findenSieaufunsererWebsite.DermitflüssigemBrennstoffbetriebenemobile
Heizofen wurde als zusätzliches Heizgerät ausgelegt und nicht als ständige
Wärmequelle.
Speziell für Großbritannien:VerwendenSieausschließlichPetroleum-Brennstoff
derKlasseC1gemäßBS2869Teil2odereinengleichwertigenBrennstoff.
ImHinblickaufdierichtigeVerwendungmussderBenutzerfolgende
Anweisungen befolgen:
ESISTVERBOTEN
- den mit flüssigem Brennstoff betriebenen mobilen Heizofen in Wohnwagen,
auf Booten und in Fahrerhäusern zu benutzen.
- den mit flüssigem Brennstoff betriebenen mobilen Heizofen in unzureichend
belüftetenRäumen(dieMindestmaßefürzubeheizendeRäumeentnehmen
SiebittederTabellemitdentechnischenDaten),Kellerräumenbzw.ineiner
Höhe von über 1500 m zu benutzen.
- Änderungen an den Sicherheitsvorrichtungen des Heizofens vorzunehmen.
Wenn diese Art von Heizung in öffentlich zugänglichen Räumen eingesetzt
werden soll, muss eine entsprechende Genehmigung vorliegen. Erkundigen
Sie sich rechtzeitig nach den entsprechenden Vorschriften.
2
20