TP-Link TD-8616 User manual

1
Turn off all of your network devices, including your computer and the Modem.
Connect your computer to the
Port labeled “LAN” on the
Modem Router with an
Ethernet cable.
Connect the splitter to the wall
j
ack using a telephone line,
then use the other telephone
line to directly connect it to the
LINE port on the Modem
Router and the MODEM port
of the splitter, also have the
PHONE port of the splitter
connected to a telephone.

2
ADSL: Flashing when the modem
is synchronizing; Solid light if the
modem is synchronized
If no telephone is needed, please connect the LINE port of the Modem to the
wall jack using the telephone line directly.
Turn on all of your network devices, including your computer and the Modem
then check to see if the LEDs of the Modem display normally as the diagram
below describes.
If the LEDs display abnormally, please check to see if all the cable connectors
(power adapter, phone line and Ethernet cable) are well connected to your
device. With the phone line well connected, if the ADSL LED turns off after a
quick-flash, please contact your ISP to ensure that your internet connection is
active.
Note
Note
Power: Solid light
LAN: Solid light if the LAN port is
connected
Plug the provided Power Adapte
r
into the Power jack on the back o
f
the Modem and the other end to a
standard electrical wall socket.

3
Configure your computer’s IP Address
For Windows XP OS
Go to Start > Settings > Control
Panel, and then you will see the
following page.
Click Network and
Internet Connections
Click Properties
Click Network
Connections
Right-click Local Area
Connection

4
Double-click Internet
Protocol (TCP/IP)
Select Use the following
IP address
Enter 192.168.1.2 into the IP
address field, 255.255.255.0
into the Subnet mask filed.
Click OK

5
Click OK
For Windows Vista OS
Go to Start > Settings > Control
Panel, and then you will see the
following page.
Click View Network
Status and Tasks
Click
V
iew Status

6
Click Properties
Double-click Internet Protocol
Version 4

7
Click OK
Click OK
Select Use the following
IP address
Enter 192.168.1.2 into the IP
address field, 255.255.255.0
into the Subnet mask filed.

8
For Windows 7 OS
Go to Start > Settings > Control
Panel, and then you will see the
following page.
Click View network
status and tasks
Click Change adapter settings
Click Properties
Right-click Local Area
Connection

9
Double-click Internet
Protocol Version 4
(TCP/IPv4)
Select Obtain an IP
address automatically
Select Obtain DNS server
address automatically
Click OK

10
Click OK
Login
If you forget the password, please refer to T2 in the Troubleshooting guide.
A dialog box will prompt you fo
r
the User name and Password.
Enter the default values and
click OK.
Note
User nameǖadmin
Passwordǖadmin
The web management page will
display after a successful login.
Open your web browser and
type in 192.168.1.1 in the
address bar and press Enter.

11
Click Save
Internet Parameters Configuration
2
Note
Choose Basic Setup ŚWAN
Setting, then this page will
display.
Enter the VPI,VCI values
provided by your ISP.
If you did not get the VPI, VCI information, please contact your ISP for this
information.

12
For Windows XP OS
Click the “StartÆAll
ProgramsÆAccessoriesÆ
CommunicationsÆNew
connection wizard” to
launch the wizard.
Click Next
To connect to the Internet, please run the dialing software such as WinPoet
or EnterNet to do the virtual dialing as the following described.
Note

13
Select the “connect using
a broadband connection
that requires user name
and
p
assword”
Select the “connect
to the Internet”
Click Next
Select the “set up my
connection manually”
Click Next
Click Next

14
.
Click Next
Type an ISP Name to
identify your connection
Click Next
Note If you did not get the User name or Password, please contact your ISP fo
r
this information.
Enter the User name
and Password given
by your ISP.
Click Finish
Add a shortcut to
this connection to
my desktop for
convenience.

15
After you have successfuly created the connection, the shortcut icon of this
connection will appear on your desktop. When you want to access the Internet,
double-click the icon to load the following screen.
For Windows Vista OS
Note The User name and Password displayed here are given by your ISP,
which you have entered during the New Connection Wizard.
Click the “StartÆControl
Panel”
Click Connect

16
Double-click Network
and Sharing Center
Click Connect to
the Internet
Click Next
Click Set up a
connection or network

17
Click Broadband
(
PPPoE
)
Enter the User name
and Password given
by your ISP.
Type a Connection
name to identify your
co
nn
ect
i
o
n
Click Connect
Click Connect
Note The User name and Password displayed here are given by your ISP,
which you have entered on last step.

18
For Windows 7 OS
Note To connect to the Internet next time, click the Start button; click Connect to,
and then click the connection you just created.
Click the “StartÆControl
Panel”
Click Close to
finish the setup

19
Click Network and
Sharing Center
Click Set up a
connection or network
Click Connect to
the Internet
Click Next

20
Click Broadband
(PPPoE)
Enter the User name
and Password given
by your ISP.
Type a Connection
name to identify your
co
nn
ect
i
o
n
Click Connect
Click Connect
Note The User name and Password displayed here are given by your ISP,
which you have entered on last step.