TP-Link P1201-08 User manual

GPON OLT Products User Manual
P1201-08
---Quick Configuration Guide
Version：V1.0
1910020846 REV1.0.1

© COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-Link Technologies Co., Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used
to make any derivative such as translation, transformation, or adaptation without
permission from TP-Link Technologies Co., Ltd. Copyright © 2018 TP-Link
Technologies Co., Ltd. All rights reserved.
About This Manual
This manual is applicable to P1201-08 GPON OLT products quickly installation
configuration guide, Is the user to quickly and easily manage GPON OLT equipment
should read the information before guidelines.
The related documents for GPON OLT device are:
《P1201-08 OLT User Manual-Device Install Guide》
《P1201-08 OLT User Manual-Command Line Operation》
《P1201-08 OLT User Manual-EMS Configuration Guide》

I
Content
1. Instruction .............................................................................................................1
Revision History ...............................................................................................................1
Proper Noun......................................................................................................................1
Note...................................................................................................................................1
2. OLT Login Manage................................................................................................2
2.1 OLT Login Manage Explanation...........................................................................2
2.2 OLT Login By Console.........................................................................................2
2.3 OLT Login By Telnet ............................................................................................3
3. OLT Upgrade.........................................................................................................4
4. Configure Service In OLT Discrete Mode（Non-Template）................................. 5
4.1 FTTH Service Topology........................................................................................6
4.2 Data Plan...............................................................................................................6
4.3 Config Process ......................................................................................................7
4.4 Configure OLT Service .........................................................................................7
4.4.1 Configure OLT Global Vlan.............................................................................7
4.4.2 Configure OLT GE Port Service Vlan..............................................................7
4.4.3 Configure DBAProfile ....................................................................................9
4.4.4 Configure ONT Lineprofile..............................................................................9
4.4.5 Configure ONT Srvprofile .............................................................................10
4.4.6 Configure OLT Multicast vlan .......................................................................10
4.5 Check ONT Register Status. ...............................................................................10
4.6 Configure Bridge ONT(SFU) Service.................................................................10
4.6.1 Configure Bridge ONT(SFU) Internet Service ..............................................10
4.6.2 Configure Bridge ONT (SFU) Multicast Service...........................................11
4.7 Configure Gateway ONT（HGU）Service........................................................12
4.7.1 Configure Gateway ONT（HGU）Internet Service--RTK Solution ............12
4.7.2 Configure Gateway ONT（HGU）Multicast Service--RTK Solution..........14
4.7.3 Configure Gateway ONT（HGU）Internet Service--ZTE Solution.............15
4.7.4 Configure Gateway ONT（HGU）Multicast Service--ZTE Solution ..........17
4.7.5 Configure Gateway ONT（HGU）VOIP Service--ZTE Solution................19
5. Configure Service In OLT Profile Mode............................................................... 22
5.1 Data Plan.............................................................................................................22
5.2 Configure Process...............................................................................................22
5.3 Configure OLT Service .......................................................................................23
5.3.1 Configure OLT Globle Vlan...........................................................................23
5.3.2 Configure OLT GE Port Service Vlan............................................................23
5.3.3 Configure OLT Multicast Service ..................................................................24
5.4 Create ONT Profile .............................................................................................24
5.4.1 Create ONT DBA Profile ...............................................................................24
5.4.2 Create ONT Lineprofile .................................................................................25
5.4.3 Create ONT Srvprofile...................................................................................25
5.5 Add ONT Manually ............................................................................................26

II
5.6 Check ONT Registration Status..........................................................................26
5.7 Configure Bridge ONT（SFU）Service ............................................................27
5.7.1 Configure Bridge ONT (SFU) Internet Service .............................................27
5.7.2 Configure Bridge ONT (SFU) IPTV Service.................................................27
5.8 Gateway ONT（HGU）Service Configure Introduction...................................28
6. Configure OLT QinQ Service............................................................................... 28
6.1 Data Plan.............................................................................................................28
6.2 Configure Processes............................................................................................29
6.3 Configure OLT....................................................................................................29
7. Common Command Description.......................................................................... 30

1
1. Instruction
Revision History
Date
Version
Description
2018-08-15
V1.0
New Version GPON OLT First Edition, Configuration Guide
2018-12-04
V1.0.1
Product image updated and some minor alterations
Proper Noun
Acronym
Full name
Instructions
GPON
Gigabit-Capable Passive Optical
Network
Gigabit Capable Passive Optical Network
OLT
Optical Line Terminal
Optical Line Terminal
ONT
Optical Network Terminal
Optical Network Terminal
OMCI
ONT Management and Control
Interface
GPON OLT&ONT Management and
Control Interface(protocol)
OAM
OperationAdministration and
Maintenance
EPON OLT&ONU Operation
Administration and Maintenance Protocol
DBA
Dynamic Bandwidth Allocation
Dynamic Bandwidth Allocation
VLAN
Virtual Local Area Network
Virtual Local Area Network
VoIP
Voice over IP
Voice over IP
WLAN
Wireless Local Area Networks
Wireless Local Area Networks
FTTH
Fiber To The Home
Fiber To The Home
FTTB
Fiber To The Building
Fiber To The Building
Note
The command line described in the document is case sensitive in OLT.
If we meet a command that cannot be inputted or is prompted for error, we can input “?”to
see the latter command format.
Input incomplete commands can be completed by pressing the “Tab”key.
P1201-08 is Pizza-Box OLT，only have one card，so, if we want to enter PON mode, need
input interface gpon 0/0

2
2. OLT Login Manage
2.1 OLT Login Manage Explanation
P1201-08 OLT support CLI management; CLI manage type divided into telnet remote manage and
console local manage, please check #2.2 and #2.3 chapter to see concrete operations; please check
EMS user manual to see EMS manage way; please check #4 to see WEB manage way.
2.2 OLT Login By Console
First, find console port on OLT front surface, which is a RJ45 port. if want to login OLT by
Console port, we need do prepare as follows:
Need RJ-45-to-DB-9 serial line
Connect PC to OLT console port, find COM number in “computer management”
Software for logging in OLT by console port(Putty, SecureCRT)
parameter for console login software
BaudRate:9600 (Note：8PON Port OLT is 9600，16 PON Port OLT is 115200)
Parity Check: None
Databit: 8
Stopbit: 1
Flow Control: None
Login OLT by console login software, then input username: root, password: admin
[OLT console connection diagram]
[OLT console connection device]

3
Port on Computer
Required Cable
Port on OLT
Serial Port
RJ-45 to DB-9 Console Cable
RJ-45 Console Port
USB Type-A Port
USB to RS-232 compatible serial port adapter ( Adapter may
require a software driver )
RJ-45 to DB-9 Console Cable
2.3 OLT Login By Telnet
There are two way to telnet, one is outband management, another is inband management.
1. Outband management (connect OLT MGMT port).
set PC ip as 192.168.1.X(except 192.168.1.100),PC connect to OLT MGMT port, login the OLT
with OLT default manage IP (default IP : 192.168.1.100). then input username and password,
default login username is root, password is admin.
Use command as follow can modify the outband management IP:
OLT> enable
OLT# config
OLT(config)# interface mgmt
OLT(config-interface-mgmt)# ip address 192.168.5.100 24
OLT(config-interface-mgmt)# exit
2. Inband management(connect OLT ge port)
First we login olt via console port or mgmt port, and add a vlanif for inband management,
assigned an IP address to this vlan, add the ge port to the vlan, ge port vlan mode can be access or
trunk, which depend on your network environment, then pc connect to OLT ge port（ge1-ge4）and
telnet to the OLT.
The way to set inband mangement ip as follows：
OLT> enable
OLT# config
OLT(config)# vlan 100
OLT(config)# interface ge
OLT(interface-ge)# vlan access 1 100 ----configure ge 1 as inband management port
OLT(interface-ge)# exit
OLT(config)# interface vlanif 100

4
OLT(interface-vlanif-100)# ip address 192.168.2.100 255.255.255.0
OLT(interface-vlanif-100)# exit
3. OLT Upgrade
1. Set up OLT update topology:
Use a PC as FTP server (run wftpd32.exe or Wftpd.exe in this pc), and connect to OLT mgmt port
or ge port to transmit firmware.
2. Test network connectivity
a) Connect PC to OLT console port, used for updating OLT in boot mode.
b)Connect pc to OLT MGMT port or ge port, configure PC ip and OLT ip(inband ip or outband
ip) are in same segment.
c) PC can ping OLT manegemnet IP, if pc can ping OLT manegemnet ip, means OLT can
connect to FTP server.
d)Close PC firewall, prevent firewall intercept FTP software.
3. FTP server configuration
a. Open FTP software, configure FTP username and password, such as: admin/admin
b. Set up a directory of OLT update files for the FTP server, such as the way for setting up the
wftp32. Exe software：
---Security -> User/Rights Security Dialog -> User Name —input admin
---Change Password —input admin
---Home Directory —set directory of OLT upgrade files

5
4. OLT update command
P1201-08 OLT only need to update a file, if the boot file is too old, we need update boot file in
OLT boot mode, boot upgrade way will be provided separately. OLT the common upgrade method
please see below:
a. Input command as follows to update OLT FW file(file name include FW )：
OLT(config)# load packetfile ftp 192.168.1.222 admin admin New16Port_FW_V1.3.1_X000
_171114_1841.img
Broadcast message from root:
Upgrade is in process.
File [New16Port _FW_V1.3.1_X000_171114_1841.img] download .......... OK
File [New16Port _FW_V1.3.1_X000_171114_1841.img] upgrade .......... OK
b. After update OLT, we need reboot OLT(Note: only reboot OLT,OLT can use new
version)
OLT(config)# reboot
Please check whether data has saved, the unsaved data will lose if reboot system. Are you sure to
reboot system? (y/n)[n]:y
4. Configure Service In OLT Discrete Mode
（Non-Template）
This section mainly introduce P1201-08 OLT internet service, voice service and multicast service
in discrete mode in FTTH environment. Mainly introduce the bridge ONT(SFU and Home
Gateway ONT (HGU),The following will introduce the service configuration way for OLT and
ONT according to two types ONT.

6
4.1 FTTH Service Topology
4.2 Data Plan
Main Data Plan List
Configure Iteam
Data
OLT Port Config
Ge1：VLAN 100 access mode
Ge2：VLAN 200 access mode
Ge3：VLAN 300 access mode
DBA Profile（upload
bandwidth control）
Profile number：1
ONT Lineprofile
Profile ID：0
T-CONT ID：1
Internet GEM Port ID：2 Mapping Vlan：100
Voice GEM Port ID：3 Mapping Vlan：200
IPTV GEM Port ID：4 Mapping Vlan：300
ONT Srvprofile
Profile ID：0
ONT Port Capability：adaptive
Bridge ONT Port
Config
LAN 1：VLAN 100
LAN 2：VLAN 200
LAN 3：VLAN 300 ---connect to VOIP phone
Gateway ONT Port
Config
LAN1：VLAN 100
LAN2：VLAN 200
POTS1：VLAN 300

7
4.3 Config Process
4.4 Configure OLT Service
4.4.1 Configure OLT Global Vlan
In config mode, we can use OLT(config)# show vlan all to show the created vlan.
If the created vlan can’t meet the need, we can use command OLT(config)# vlan vlan-list to create
new vlan, According to the data plan, we create vlan100,vlan200,vlan300 firstly:
OLT(config)# vlan 100
OLT(config)# vlan 200
OLT(config)# vlan 300
4.4.2 Configure OLT GE Port Service Vlan
We can config GE port vlan mode as access, hybrid and trunk, we can configure different mode
according to our network plan, configure way of three mode as follows.
Configure GE 1,2,3 port vlan mode is access(in this document, GE port connect to PC, so we
configure ge port vlan mode as access):
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 access
OLT(config-interface-ge-0/0)# vlan access 1 100
OLT(config-interface-ge-0/0)# vlan access 2 200
OLT(config-interface-ge-0/0)# vlan access 3 300
OLT(config-interface-ge-0/0)# exit
Configure GE 1、2、3 vlan mode is trunk：
OLT(config)# interface ge 0/0

8
OLT(config-interface-ge-0/0)# vlan mode 1-3 trunk
OLT(config-interface-ge-0/0)# vlan trunk 1 100
OLT(config-interface-ge-0/0)# vlan trunk 2 200
OLT(config-interface-ge-0/0)# vlan trunk 3 300
OLT(config-interface-ge-0/0)# exit
Configure GE 1、2、3 vlan mode is hybrid：
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 hybrid
OLT(config-interface-ge-0/0)# vlan hybrid 1 tagged 100
OLT(config-interface-ge-0/0)# vlan hybrid 2 tagged 200
OLT(config-interface-ge-0/0)# vlan hybrid 3 tagged 300
OLT(config-interface-ge-0/0)# exit
NOTE：
The OLT vlan handle process as follows:
Vlan mode
Direction
Message have
vlan tag or not
Handling method
Access mode
In
vlan tag
Discard
untag
Add port configured vlan in access mode for
message (main parameter is VID),and forward
Out
vlan tag
Forward message to the corresponding port
according to VID and remove vlan tag;If the
VLAN ID of the Tagged message is not same
to the port VID, it is discard.
untag
Discard
Trunk mode
In
vlan tag
If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the
VLAN in the message doesn’t permit to pass
port, it is discarded.
untag
Add default vlan(native-vlan) for untagged
message and forward.
Out
vlan tag
If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the
VLAN ID of the message is the default
(native- VLAN)VLAN, then the VLAN tag is
discard and forward; If the VLAN in the
message doesn’t permit to pass port, it is
discarded.

9
untag
Discard
Hybrid
mode
In
vlan tag
If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the
VLAN in the message doesn’t permit to pass
port, it is discarded.
untag
Add default vlan(native-vlan) for untagged
message and forward.
Out
vlan tag
If the VLAN in the message is permit to pass
port, according vlan tag or vlan untag of
message to discard or no discard vlan tag, then
forward message, If the VLAN ID of the
message is the default (native-VLAN) VLAN,
then the VLAN tag is discard and forward; If
the VLAN in the message doesn’t permit to
pass port, it is discarded.
untag
Discard
4.4.3 Configure DBAProfile
In OLT discrete mode, ONT is automatically registered. When ONT online it would bind system
default lineprofile 0 and srvprofile 0 automatically. And the TCONT 1 of lineprofile 0, would bind
the DBA profile 1 automatically. In this user manual don’t modify DBA profile 1 configuration and
use it directly
4.4.4 Configure ONT Lineprofile
In OLT discrete mode, ONT is automatically registered. When ONT online it would bind system
default lineprofile 0 and srvprofile 0 automatically. And the lineprofile 0 would create gem 1 to bind
TCONT 1 automatically. Gem 1 can be deleted or modified manually. In this user manual don’t
modify gem1 and create new gem for different service as flow:
OLT(config)# ont-lineprofile gpon profile-id 0
OLT(config-ont-lineprofile-0)# gem add 2 tcont 1
OLT(config-ont-lineprofile-0)# gem mapping 2 1 vlan 100
OLT(config-ont-lineprofile-0)# gem add 3 tcont 1
OLT(config-ont-lineprofile-0)# gem mapping 3 1 vlan 200
OLT(config-ont-lineprofile-0)# gem add 4 tcont 1
OLT(config-ont-lineprofile-0)# gem mapping 4 1 vlan 300
OLT(config-ont-lineprofile-0)# commit
OLT(config-ont-lineprofile-0)# exit

10
4.4.5 Configure ONT Srvprofile
In OLT discrete mode, ONT is automatically registered. When ONT online it would bind system
default lineprofile 0 and srvprofile 0 automatically. In this user manual don’t modify ont srvprofile 0
configuration and use it directly.
4.4.6 Configure OLT Multicast vlan
OLT(config)# multicast-vlan 200
OLT(config-multicast-vlan-200)# igmp member port gpon 0/0/1
OLT(config-multicast-vlan-200)# exit
4.5 Check ONT Register Status.
In OLT discrete mode, ONT is automatically registered. after ONT is automatically registered, use
command show ont info to query ONT online status. make sure ONT “Control flag” is ”Active”, ”Run
State” is ”Online”, “Config state” is “Success” and “Match state” is “Match”
OLT(config-interface-gpon-0/0)# show ont info 1 all
--------------------------------------------------------------------------------------------------
F/S P ONT SN Control Run Config Match
ID flag state state state
------------------------------------------------------------------------------------------------
0/0 1 1 DB19B34F0C16 Active online success match
0/0 1 2 XPONE067B341 Active online success match
--------------------------------------------------------------------------------------------------
Total: 2, online 2, deactive: 0, failed: 0
4.6 Configure Bridge ONT(SFU) Service
In OLT discrete mode,we need enter OLT to config ONT one by one,config way as follows:
4.6.1 Configure Bridge ONT(SFU) Internet Service
Premise condition of ONT to open internet service:
OLT connect to uplink device and open internet service
OLT have created vlan for internet service
OLT have configured GE port vlan
ONT have registered
SFU ethernet port vlan mode have transparent, tag(access),trunk mode and so on, we can according to
our network plan configure different mode. all ont vlan is configured by OLT, configure way as
follows:
Configure traffic profile:

11
OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs
2000
Configure ONT1 eth1 vlan mode is tag(access):
OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 1 vlan 100
OLT(config-interface-gpon-0/0)# exit
Config service port:
OLT(config)# service-port 3 vlan 100 gpon 0/0 port 1 ont 1 gemport 2 multi-service user-vlan
100 tag-action transparent inbound name 10M outbound name 10M
NOTE：
In this user manual service use single vlan. SVLAN is 100, USERVLAN is 100. Tag-action is
transparent. USERVLAN equal SVLAN. So the service-port transparent vlan 100. More Tag action
rule as follow:
TAGACTION
Description
DEFAULT
Add a SVLAN to packet.
ADD_DOUBLE
Add a SVLAN and a USERVLAN to packet.
TRANSPARENT
When USERVLAN equal SVLAN would transparent packet.
TRANSLATE
Translate USERVLAN to SVLAN.
TRANSLATE_AND_A
DD
Add a SVLAN and translate USERVLAN to the new innervlan
4.6.2 Configure Bridge ONT (SFU) Multicast Service
Premise Condition
OLT connect to uplink device and open service
OLT have created vlan for multicast service
OLT have configured GE port vlan
ONT have registered
Configure ONT1 multicast vlan mode is igmp-snooping-proxy, and multicast-forward is untag:
OLT(config)# ont-srvprofile gpon profile-id 0
OLT(config-ont-srvprofile-0)# multicast mode igmp-snooping-proxy
OLT(config-ont-srvprofile-0)# multicast-forward untag
OLT(config-ont-srvprofile-0)# exit
Configure ONT1 eth2 vlan mode is tag (access):
OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 2 vlan 200

12
OLT(config-interface-gpon-0/0)# exit
Config service port:
OLT(config)# service-port 4 vlan 200 gpon 0/0 port 1 ont 1 gemport 3 multi-service user-vlan
200 tag-action transparent inbound name 20M outbound name 20M
----End
4.7 Configure Gateway ONT（HGU）Service
Gateway ONT（HGU）can provide internet, VOIP,IPTV service for FTTH, support PPPOE/DHCP
dial-up, NAT, IGMP. Because HGU have route function, ONT service need to be configured with the
local web or tr069,include wan and vlan configuration, don’t need configure vlan in olt, only make sure
ONT can register to OLT.OLT don’t support configure ONT route wan, specific configure as follows:
4.7.1 Configure Gateway ONT（HGU）Internet Service--RTK Solution
Premise condition
OLT connect to uplink device and open service
OLT have created vlan for internet
OLT have configured GE port vlan
ONT have registered
1. Config traffic profile
OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs
2000
2. Config service port:
OLT(config)# service-port 3 vlan 100 gpon 0/0 port 1 ont 1 gemport 2 multi-service user-vlan
100 tag-action transparent inbound name 10M outbound name 10M
3. Create route wan and bind LAN1 in ont web
Click InternetInternet ConfigWAN Config

13
NOTE：
Mode select Route. Check Enable VLAN and Vlan ID input 100. Service Mode select
INTERNET. Bind port check Port_1 and wireless (SSID).
Internet service take DHCP mode as an example in this document. The service type please select
suitable type according to the user's actual environment. ONT detail usage please refer to ONT user
manual.
4. Check ONT internet wan status
Click StatusInternet Info

14
4.7.2 Configure Gateway ONT（HGU）Multicast Service--RTK Solution
premise condition
OLT connect to uplink device and open multicast service
OLT have created vlan for multicast
OLT have configured GE port multicast vlan
ONT have registered
1. Create service port
OLT(config)# service-port 5 vlan 200 gpon 0/0 port 1 ont 2 gemport 3 multi-service user-vlan
200 tag-action transparent
2. Create bridge wan and bind LAN2 in ont web
Click InternetInternet ConfigWAN Config
NOTE：
Mode select to Bridge. Check Enable Vlan, Vlan ID input 200. Service Mode select Other. Bind
port click Port_2.
3. Config IGMP mode in ONT web
Click ApplicationIGMP ConfigIGMP Snooping. Enable IGMP Snooping.
4. Configure multicast vlan on ONT web

15
Click ApplicationMulticast Vlan3_Other_B_VID_200Modify. Input 200 behind VLAN
multicast (blank said set).
5. Check ONT multicast wan status
Click StatusInternet Info
----end
4.7.3 Configure Gateway ONT（HGU）Internet Service--ZTE Solution
premise condition
OLT connect to uplink device and open internet service
OLT have created vlan for internet
OLT have configured GE port vlan
ONT have registered
1. Config traffic profile
OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs
2000
2. Config service port
OLT(config)# service-port 6 vlan 100 gpon 0/0 port 1 ont 3 gemport 2 multi-service user-vlan
100 tag-action transparent inbound name 10M outbound name 10M
3. Create route wan and bind LAN1 in ont web
Click NetworkWANWAN Connection. Type select to DHCP. Connection Name select to
Create WAN Connection. Port Binding check LAN1, LAN2, LAN3 and SSID1. Service List
select to INTERNET. VLAN Mode select to Used. VLAN ID enter 100. finaly click Create.

16
NOTE：
Type select to DHCP. Connection Name select to Create WAN Connection. Port Binding check
LAN1, LAN2, LAN3 and SSID1. Service List select to INTERNET. VLAN Mode select to Used.
VLAN ID enter 100. Enable DHCP and Enable NAT keep default checked status.
In this document, Internet service take DHCP mode as an example. please selected suitable service
type according to the user's actual need. ONT detail use way please refer to ONT user manual.
4. Check ONT internet wan status