TP-Link JetStream T1500G-10MPS User manual

User Guide
JetStream 8-Port Gigabit Smart Switch
T1500G-10MPS/T1500G-8T (TL-SG2008)
T1500G-10PS (TL-SG2210P)
REV1.0.2
1910012063

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered
trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from
TP-Link Technologies Co., Ltd. Copyright © 2017 TP-Link Technologies Co., Ltd. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.

この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こす
ことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。
VCCI-A
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
Safety Information
When product has power button, the power button is one of the way to shut off the
product; When there is no power button, the only way to completely shut off power is to
disconnect the product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者
會被要求採取某些適當的對策。
Explanation of the symbols on the product label
Symbol
Explanation
AC voltage

Symbol
Explanation
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic
equipment (WEEE). This means that this product must be handled pursuant to
European directive 2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling organization or to
the retailer when he buys a new electrical or electronic equipment.
Indoor use only

CONTENTS
Package Contents .........................................................................................................................1
Chapter 1 About this Guide ..........................................................................................................2
1.1 Intended Readers.........................................................................................................2
1.2 Conventions.................................................................................................................2
1.3 Overview of This Guide ................................................................................................2
Chapter 2 Introduction .................................................................................................................7
2.1 Overview of the Switch ................................................................................................7
2.2 Appearance Description..............................................................................................7
2.2.1 Front Panel ........................................................................................................7
2.2.2 Rear Panel ....................................................................................................... 11
Chapter 3 Login to the Switch....................................................................................................14
3.1 Login ..........................................................................................................................14
3.2 Configuration .............................................................................................................14
Chapter 4 System.......................................................................................................................16
4.1 System Info ................................................................................................................16
4.1.1 System Summary ............................................................................................16
4.1.2 Device Description..........................................................................................17
4.1.3 System Time....................................................................................................18
4.1.4 Daylight Saving Time.......................................................................................19
4.1.5 System IP.........................................................................................................20
4.2 User Management......................................................................................................22
4.2.1 User Table .......................................................................................................22
4.2.2 User Config......................................................................................................22
4.3 System Tools .............................................................................................................24
4.3.1 Boot Config .....................................................................................................24
4.3.2 Config Restore ................................................................................................24
4.3.3 Config Backup .................................................................................................25
4.3.4 Firmware Upgrade...........................................................................................26
4.3.5 System Reboot................................................................................................26
4.3.6 System Reset ..................................................................................................27
4.4 Access Security .........................................................................................................27
4.4.1Access Control................................................................................................27

4.4.2 HTTP Config ....................................................................................................28
4.4.3 HTTPS Config..................................................................................................29
4.4.4 SSH Config ......................................................................................................33
4.4.5 Telnet Config...................................................................................................39
Chapter 5 Switching ...................................................................................................................40
5.1 Port.............................................................................................................................40
5.1.1 Port Config ......................................................................................................40
5.1.2 Port Mirror .......................................................................................................41
5.1.3 Port Security....................................................................................................43
5.1.4 Port Isolation ...................................................................................................45
5.1.5 Loopback Detection........................................................................................46
5.2 LAG.............................................................................................................................48
5.2.1 LAG Table ........................................................................................................48
5.2.2 Static LAG........................................................................................................50
5.2.3 LACP Config ....................................................................................................51
5.3 Traffic Monitor ...........................................................................................................52
5.3.1 Traffic Summary ..............................................................................................52
5.3.2 Traffic Statistics ..............................................................................................53
5.4 MAC Address .............................................................................................................55
5.4.1 Address Table .................................................................................................56
5.4.2 Static Address.................................................................................................58
5.4.3 Dynamic Address ............................................................................................59
5.4.4 Filtering Address .............................................................................................61
Chapter 6 VLAN..........................................................................................................................63
6.1 802.1Q VLAN .............................................................................................................64
6.1.1 VLAN Config ....................................................................................................65
6.1.2 Port Config ......................................................................................................67
6.2 Application Example for 802.1Q VLAN ......................................................................68
Chapter 7 Spanning Tree ...........................................................................................................70
7.1 STP Config .................................................................................................................75
7.1.1 STP Config.......................................................................................................75
7.1.2 STP Summary..................................................................................................77
7.2 Port Config .................................................................................................................78
7.3 MSTP Instance ...........................................................................................................80

7.3.1 Region Config..................................................................................................80
7.3.2 Instance Config ...............................................................................................81
7.3.3 Instance Port Config .......................................................................................82
7.4 STP Security ..............................................................................................................83
7.4.1 Port Protect.....................................................................................................83
7.5 Application Example for STP Function ......................................................................86
Chapter 8 Multicast ....................................................................................................................91
8.1 IGMP Snooping ..........................................................................................................93
8.1.1 Snooping Config .............................................................................................95
8.1.2 Port Config ......................................................................................................97
8.1.3 VLAN Config ....................................................................................................98
8.1.4 Multicast VLAN................................................................................................99
8.1.5 Querier Config ...............................................................................................103
8.1.6 Profile Config.................................................................................................104
8.1.7 Profile Binding ...............................................................................................106
8.1.8 Packet Statistics ...........................................................................................107
8.2 Multicast Table.........................................................................................................108
8.2.1 IPv4 Multicast Table ......................................................................................109
8.2.2 Static IPv4 Multicast Table............................................................................109
Chapter 9 QoS.......................................................................................................................... 112
9.1 DiffServ .................................................................................................................... 115
9.1.1 Port Priority ................................................................................................... 115
9.1.2 Schedule Mode ............................................................................................. 116
9.1.3 802.1P Priority............................................................................................... 117
9.1.4 DSCP Priority................................................................................................. 118
9.2 Bandwidth Control ................................................................................................... 119
9.2.1 Rate Limit....................................................................................................... 119
9.2.2 Storm Control................................................................................................120
9.3 Voice VLAN ..............................................................................................................121
9.3.1 Global Config.................................................................................................124
9.3.2 Port Config ....................................................................................................124
9.3.3 OUI Config .....................................................................................................126
Chapter 10 PoE ..........................................................................................................................128
10.1 PoE Config ...............................................................................................................129

10.1.1 PoE Config.....................................................................................................129
10.1.2 PoE Profile .....................................................................................................130
10.2 Time-Range..............................................................................................................131
10.2.1 Time-Range Summary...................................................................................131
10.2.2 Time-Range Create .......................................................................................132
10.2.3 Holiday Config ...............................................................................................134
Chapter 11 ACL ..........................................................................................................................135
11.1 ACL Config ...............................................................................................................135
11.1.1 ACL Summary................................................................................................135
11.1.2 ACL Create ....................................................................................................135
11.1.3 MAC ACL .......................................................................................................136
11.1.4 Standard-IP ACL............................................................................................137
11.1.5 Extend-IP ACL ...............................................................................................137
11.2 Policy Config ............................................................................................................138
11.2.1 Policy Summary.............................................................................................139
11.2.2 Policy Create .................................................................................................139
11.2.3 Action Create ................................................................................................139
11.3 ACL Binding..............................................................................................................140
11.3.1 Binding Table.................................................................................................140
11.3.2 Port Binding ...................................................................................................141
11.3.3 VLAN Binding.................................................................................................142
11.4 Policy Binding...........................................................................................................143
11.4.1 Binding Table.................................................................................................143
11.4.2 Port Binding...................................................................................................144
11.4.3 VLAN Binding.................................................................................................145
11.5 Application Example for ACL ...................................................................................146
Chapter 12 Network Security.....................................................................................................148
12.1 IP-MAC Binding ........................................................................................................148
12.1.1 Binding Table.................................................................................................148
12.1.2 Manual Binding ..............................................................................................150
12.1.3 ARP Scanning................................................................................................151
12.2 DHCP Snooping .......................................................................................................153
12.2.1 Global Config.................................................................................................156
12.2.2 Port Config ....................................................................................................157

12.2.3 Option 82 Config ...........................................................................................158
12.3 ARP Inspection.........................................................................................................159
12.3.1 ARP Detect ....................................................................................................162
12.3.2 ARP Defend ...................................................................................................164
12.3.3 ARP Statistics................................................................................................165
12.4 DoS Defend..............................................................................................................165
12.4.1 DoS Defend ...................................................................................................167
12.5 802.1X ......................................................................................................................168
12.5.1 Global Config.................................................................................................172
12.5.2 Port Config ....................................................................................................174
12.6 AAA ..........................................................................................................................176
12.6.1 Global Config.................................................................................................177
12.6.2 Privilege Elevation .........................................................................................177
12.6.3 RADIUS Server Config...................................................................................177
12.6.4 TACACS+ Server Config ...............................................................................178
12.6.5 Authentication Server Group Config.............................................................179
12.6.6 Authentication Method List Config ...............................................................181
12.6.7 Application Authentication List Config .........................................................182
12.6.8 802.1X Authentication Server Config ...........................................................183
12.6.9 Default Settings.............................................................................................183
Chapter 13 SNMP.......................................................................................................................185
13.1 SNMP Config............................................................................................................187
13.1.1 Global Config.................................................................................................187
13.1.2 SNMP View ....................................................................................................188
13.1.3 SNMP Group..................................................................................................189
13.1.4 SNMP User ....................................................................................................191
13.1.5 SNMP Community .........................................................................................192
13.2 Notification...............................................................................................................195
13.3 RMON .......................................................................................................................196
13.3.1 Statistics........................................................................................................197
13.3.2 History ...........................................................................................................198
13.3.3 Event..............................................................................................................199
13.3.4 Alarm .............................................................................................................200
Chapter 14 LLDP ........................................................................................................................202

14.1 Basic Config .............................................................................................................207
14.1.1 Global Config.................................................................................................207
14.1.2 Port Config ....................................................................................................208
14.2 Device Info ...............................................................................................................209
14.2.1 Local Info.......................................................................................................209
14.2.2 Neighbor Info................................................................................................. 211
14.3 Device Statistics ......................................................................................................212
14.4 LLDP-MED................................................................................................................213
14.4.1 Global Config.................................................................................................214
14.4.2 Port Config ....................................................................................................215
14.4.3 Local Info.......................................................................................................216
14.4.4 Neighbor Info.................................................................................................217
Chapter 15 Maintenance............................................................................................................219
15.1 System Monitor........................................................................................................219
15.1.1 CPU Monitor ..................................................................................................219
15.1.2 Memory Monitor............................................................................................220
15.2 Log ...........................................................................................................................221
15.2.1 Log Table.......................................................................................................222
15.2.2 Local Log.......................................................................................................223
15.2.3 Remote Log...................................................................................................223
15.2.4 Backup Log....................................................................................................224
15.3 Device Diagnostics ..................................................................................................225
15.3.1 Cable Test .....................................................................................................225
15.4 Network Diagnostics................................................................................................226
15.4.1 Ping................................................................................................................226
15.4.2 Tracert...........................................................................................................227
Appendix A: Specifications........................................................................................................228
Appendix B: Glossary.................................................................................................................230

Package Contents
The following items should be found in your box:
One Gigabit Smart Switch
One power cord
Four rubber cushions
Two mounting brackets and other fittings
Installation Guide
Resource CD, including:
•This User Guide
•CLI Reference Guide
•SNMP Mibs
•Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
1

Chapter 1 About this Guide
This User Guide contains information for setup and management of T1500G-10MPS/
T1500G-8T/T1500G-10PS JetStream 8-Port Gigabit Smart Switch. Please read this guide
carefully before operation.
1.1 Intended Readers
This Guide is intended for network managers familiar with IT concepts and network
terminologies.
1.2 Conventions
In this Guide the following conventions are used:
The switch or device mentioned in this Guide stands for T1500G-10MPS/T1500G-8T/
T1500G-10PS JetStream 8-Port Gigabit Smart Switch without any explanation.
Tips:
The T1500G-10MPS/T1500G-8T/T1500G-10PS switchs are sharing this User Guide. They just
differ in the number of LED indicators and ports. For simplicity, we will take T1500G-10MPS for
example throughout this Guide. However, differences with significance will be presented with
figures or notes as to attract your attention.
Menu Name→Submenu Name→Tab page indicates the menu structure. System→System
Info→System Summary means the System Summary page under the System Info menu
option that is located under the System menu.
Bold font indicates a button, a toolbar icon, menu or menu item.
Symbols in this Guide：
Symbol
Description
Note:
Ignoring this type of note might result in a malfunction or damage to the
device.
Tips:
This format indicates important information that helps you make better use of
your device.
1.3 Overview of This Guide
Chapter
Introduction
Chapter 1 About This Guide
Introduces the guide structure and conventions.
2

Chapter
Introduction
Chapter 2 Introduction Introduc
es the features, application and appearance of
T1500G-10MPS/T1500G-8T/T1500G-10PS.
Chapter 3 Login to the
Switch
Introduces how to log on to the Web management page.
Chapter 4 System This module is used to configure system properties of the
switch. Here mainly introduces:

System Info: Configure the description, system time and
network parameters of the switch.
User Management: Configure the user name and password
for users to log on to the Web management page with a
certain access level.
System Tools: Manage the configuration file of the switch.
Access Security:
Provide different security measures for
the login to enhance the configuration management
security.
Chapter 5 Switching This module is used to configure basic functions of the switch.
Here mainly introduces:
Port: Configure the basic features for the port.
LAG: Configure Link Aggregation Group. LAG is to combine
a number of ports together to make a single
high-bandwidth data path.
Traffic Monitor: Monitor the traffic of each port.
MAC Address: Configure the address table of the switch.

DHCP Filtering: Monitor the process of the host obtaining
the IP address from DHCP server.
Chapter 6 VLAN This module is used to configure VLANs to control broadcast
in LANs. Here mainly introduces:

802.1Q VLAN: Configure port-based VLAN.
Chapter 7 Spanning Tree This module is used to configure spanning tree function of the
switch. Here mainly introduces:

STP Config: Configure and view the global settings of
spanning tree function.
Port Config: Configure CIST parameters of ports.
MSTP Instance: Configure MSTP instances.

STP Security: Configure protection function to prevent
devices from any malicious attack against STP features.
3

Chapter
Introduction
Chapter 8 Multicast This module is used to configure multicast function of the
switch. Here mainly introduces:

IGMP Snooping: Configure global parameters of IGMP
Snooping function, port properties, VLAN and multicast
VLAN.
Multicast IP: Configure multicast IP table.
Multicast Filter: Configure multicast filter feature to restrict
users ordering multicast programs.
Packet Statistics: View the multicast data traffic on each
port of the switch, which facilitates you to monitor the IGMP
messages in the network.
Chapter 9 QoS This module is used to configure QoS function to provide
different q
uality of service for various network applications
and requirements. Here mainly introduces:
DiffServ: Configure priorities, port priority, 802.1P priority
and DSCP priority.
Bandwidth Control: Configure rate limit feature to control
the traffic rate on ea
ch port; configure storm control
feature to filter broadcast, multicast and UL frame in the
network.
Voice VLAN: Configure voice VLAN to transmit voice data
stream within the specified VLAN so as to ensure the
transmission priority of voice data stream and voice quality.
Chapter 10 PoE
This module is used to configure the PoE function for the
switch to supply power for PD devices. Here mainly
introduces:
PoE Config: Configure PoE function globally.
PoE Time-Range: Configure the effective time for PoE port
to supply power.
Chapter 11 ACL This module is used to configure match rules and process
policies of packets to filter packets in order to control the
access of the illegal users to the network. Here mainly
introduces:
ACL Config: ACL rules.
Policy Config: Configure operation policies.
Policy Binding: Bind the policy to a port/VLAN to take its
effect on a specific port/VLAN.
4

Chapter
Introduction
Chapter 12 Network Security This module is used to configure the protection measures for
the network security. Here mainly introduces:
IP-MAC Binding: Bind the IP address, MAC address, VLAN
ID and the connected Port number of the Host together.
DHCP Snooping: DHCP Snooping functions to monitor the
process of the Host obtaining the IP address from DHCP
server, and record the IP address, MAC address, VLAN and
the connected Port number of the Host for automatic
binding.

ARP Inspection: Configure ARP inspection feature to
prevent the network from ARP attacks.
DoS Defend: Configure DoS defend feature to prevent DoS
attack.
802.1X: Configure common access control mechanism for
LAN ports to solve mainly authentication and security
problems.

AAA: Configure the authentication, authorization and
accounting features.
Chapter 13 SNMP This module is used to configure SNMP function to provide a
management frame to monitor and maintain the network
devices. Here mainly introduces:
SNMP Config: Configure global settings of SNMP function.
No
tification: Configure notification function for the
management station to monitor and process the events.
RMON: Configure RMON function to monitor network more
efficiently.
Chapter 13 LLDP This module is used to configure LLDP f
unction to provide
information for SNMP applications to simplify troubleshooting.
Here mainly introduces:
Basic Config: Configure the LLDP parameters of the device.
Device Info: View the LLDP information of the local device
and its neighbors
Device Statistics: View the
LLDP statistics of the local
device

LLDP-MED: Configure LLDP-MED parameters of the device.
5

Chapter
Introduction
Chapter 14 Maintenance This module is used to assemble the commonly used system
tools to manage the switch. Here mainly introduces:

System Monitor: Monitor the memory and CPU of the
switch.
Log: View configuration parameters on the switch.
Device Diagnostics: Test the connection status of the cable
connected to the switch, test if the port of the switch and
the connected device are available.
Network Diagnostics: Test if the destination is reachable
and the account of router hops from the switch to the
destination.
Appendix A Specifications
Lists the hardware specifications of the switch.
Appendix B Glossary
Lists the glossary used in this manual.
Return to CONTENTS
6

Chapter 2 Introduction
2.1 Overview of the Switch
Designed for workgroups and departments, T1500G-10MPS/T1500G-8T/T1500G-10PS from
TP-Link provides wire-speed performance and full set of layer 2 management features. It
provides a variety of service features and multiple powerful functions with high security.
The EIA-standardized framework and smart configuration capacity can provide flexible
solutions for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and
video application. Link aggregation (LACP) increase aggregated bandwidth, optimizing the
transport of business critical data. SNMP, RMON, WEB/CLI/Telnet Log-in bring abundant
management policies.
T1500G-10MPS/T1500G-8T/T1500G-10PS integrates multiple functions
with excellent performance, and is friendly to manage, which can fully meet the need of the users
demanding higher networking performance.
2.2 Appearance Description
2.2.1 Front Panel
T1500G-10MPS
The front panel of T1500G-10MPS is shown as Figure 2-1.
Figure 2-1 Front Panel of T1500G-10MPS
The following parts are located on the front panel of T1500G-10MPS:
LEDs
T1500G-10MPS has an LED mode switch button which is for switching the LED status
indication. When the Speed LED is on, the port LED is indicating the data transmission status.
When the PoE LED is on, the port LED is indicating the power supply status. By default, the
Speed LED is on. Pressing the mode switch button, the Speed LED will turn off and the PoE LED
will light up. Then the PoE LED will turn off after being on for 60 seconds and the Speed LED will
light up again.
When the Speed LED is on, the port LED is indicating the data transmission status.
Name
Status
Indication
PWR
On
The switch is powered on
Off
The switch is powered off or power supply is abnormal
Flashing
Power supply is abnormal
7

Name
Status
Indication
SYS
Flashing
The switch is working normally.
On/Off
The switch is working abnormally.
FAN
Green
All the fans work properly.
Yellow
Not all the fans work properly.
PoE MAX
On
The remaining PoE power≤7W
Flashing The remaining PoE power keeps ≤7W after this LED is
on for 2 minutes.
Off
The remaining PoE power>7W
Speed or
PoE
Green
On A 1000Mbps device is connected to the
corresponding port, but no activity.
Flashing
Data is being transmitted or received.
Yellow
On A 10/100Mbps device is connected to the
corresponding port, but no activity.
Flashing
Data is being transmitted or received.
Off
No device is connected to the corresponding port.
SPF1, SFP2
Green
On A 1000Mbps device is connected to the
corresponding port, but no activity.
Flashing
Data is being transmitted or received.
Yellow
On A 100Mbps device is connected to the corresponding
port, but no activity.
Flashing
Data is being transmitted or received.
Off
No device is connected to the corresponding port.
When the PoE LED is on, the port LED is indicating the power supply status.
Name
Status
Indication
PWR
On
The switch is powered on.
Off
The switch is powered off or power supply is abnormal.
Flashing
Power supply is abnormal.
SYS
Flashing
The switch is working normally.
On/Off
The switch is working abnormally.
FAN
Green
All the fans work properly.
Yellow
Not all the fans work properly.
8

Name
Status
Indication
PoE MAX
On
The remaining PoE power≤7W
Flashing The remaining PoE power keeps ≤7W after this LED is
on for 2 minutes.
Off
The remaining PoE power>7W
Speed or
PoE
Green
On
The port is supplying power normally.
Flashing The supply power exceeds the corresponding port's
maximum power.
Yellow
On
Overload or short circuit is detected.
Flashing
Power-on self-test has failed.
Off
No device is connected to the corresponding port.
SPF1, SFP2
Green
On A 1000Mbps device is connected to the
corresponding port, but no activity.
Flashing
Data is being transmitted or received.
Yellow
On A 100Mbps device is connected to the corresponding
port, but no activity.
Flashing
Data is being transmitted or received.
Off
No device is connected to the corresponding port.
Reset
Press this button for five seconds or above to reset the software setting back to factory default
setting.
10/100/1000Mbps RJ45 Port and PoE Port
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each
has a corresponding Speed or PoE LED.
SFP Port
Designed to install the SFP module. T1500G-10MPS features 2 SFP transceiver ports.
T1500G-8T
The front panel of T1500G-8T is shown as Figure 2-2.
Figure 2-2 Front Panel of T1500G-8T
9

The following parts are located on the front panel of T1500G-8T:
LEDs
Name
Status
Indication
Power
On
The switch is powered on.
Off
The switch is powered off or power supply is abnormal.
Flashing
Power supply is abnormal.
System
Flashing
The switch is working normally.
On/Off
The switch is working abnormally.
1-8
On (Green) The corresponding port is connected to a 1000Mbps
device.
On (Yellow) The corresponding port is connected to a
10/100Mbps device.
Flashing
The corresponding port is transmitting/receiving data.
Reset
Press this button for five seconds or above to reset the software setting back to factory default
settings.
T1500G-10PS
The front panel of T1500G-10PS is shown as Figure 2-3.
Figure 2-3 Front Panel of T1500G-10PS
The following parts are located on the front panel of T1500G-8T:
Name
Status
Indication
Power
On(Green)
The switch is powered on.
Flashing/Off
The switch is powered off or power supply is abnormal.
System
Flashing
The switch is working normally.
On/Off
The switch is working abnormally.
PoE MAX
On
The remaining PoE power≤7W
Flashing The remaining PoE power keeps ≤7W after this LED is
on for 2 minutes.
Off
The remaining PoE power>7W
10