TP-Link TL-SL2210WEB User manual

User Guide
Gigabit Uplink Web Smart Switch
TL-SL2210WEB/TL-SL2218WEB
TL-SL2428WEB/TL-SL2452WEB
Enterprise Networking Solution

I

Specifications are subject to change without notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their
respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.1)
This device must accept any interference received, including interference that may cause2)
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Copyright & Trademarks

II

This User Guide is also available in PDF on our website. To obtain the latest
product information, please visit the official website:
http://www.tp-link.com

This User Guide describes the hardware characteristics, installation methods
and the points that should be attended to during installation. This User Guide is
structured as follows:
Chapter 1 Introduction. This chapter describes the external components of
the Switch.
Chapter 2 Installation. This chapter illustrates how to install the Switch.
Chapter 3 Lightning Protection. This chapter illustrates how to prevent
lightning damage.
Chapter 4 Connection. This chapter illustrates how to do the physical connec-
tion of the Switch.
Chapter 5 Function Description. This chapter describes the functions sup-
ported by the switch family and presents the network concepts referred in this
Guide.
Chapter 6 Web Management. This chapter gives an explanation to the terms
in WEB interface and describes the configuring suggestions of the Switch.
Appendix A Troubleshooting.
Appendix B Table of Factory Defaults.
Appendix C Table of Funtion Differences of Switch Family.
Appendix D Hardware Specifications.
Appendix E Technical Support.
Related Document

III

This User Guide is for:
Network Engineer
Network Administrator

Due to the similarity in structure of TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/
TL-SL2452WEB Gigabit Uplink Web Smart Switch series, in this User Guide we
take TL-SL2210WEB as an example to illustrate Chapter 2 Installation, Chapter 3
Lightning Protection, Chapter 4 Connection and Chapter 6 WEB Management.
This Guide uses the specific formats to highlight special messages. The following
table lists the notice icons that are used throughout this guide.
Remind to be careful. A caution indicates a potential which may result in
device damage.
Remind to take notice. The note contains the helpful information for a
better use of the product.
Remind to get further information. The further information provides you
more details about the product.
Audience

IV

Contents
Chapter 1 Introduction ——————————————— 01
1.1 Product Overview............................................................................................ 01
1.2 Features............................................................................................................... 01
1.3 Appearance........................................................................................................ 02
Chapter 2 Installation ———————————————— 05
2.1 Package Contents ............................................................................................ 05
2.2 Safety Precautions ........................................................................................... 05
2.3 Installation Tools............................................................................................... 08
2.4 Product Installation......................................................................................... 08
Chapter 3 Lightning Protection ———————————— 10
3.1 Cabling Reasonably......................................................................................... 10
3.2 Connect to Ground.......................................................................................... 12
Chapter 4 Connection ——————————————— 13
4.1 Ethernet Port ..................................................................................................... 13
4.2 SFP Port ............................................................................................................... 13
4.3 Verify Installation ............................................................................................. 14
4.4 Power On............................................................................................................. 14
Chapter 5 Function Description
———————————— 15
5.1 System Setting.................................................................................................. 15
5.1.1 System Setting .......................................................................................... 15
5.1.2 File Transfer ................................................................................................ 15
5.1.3 Reboot & Reset.......................................................................................... 15
5.1.4 User ............................................................................................................... 15
5.2 Port Setting ........................................................................................................ 15
5.2.1 Port Parameter.......................................................................................... 15
5.2.2 Port Statistic and Port Status ............................................................... 16
5.2.3 Storm Control............................................................................................ 16
5.2.4 Port Description ....................................................................................... 16
5.3 Network Setting ............................................................................................... 17
5.3.1 Network Setting ....................................................................................... 17
5.3.2 Aging Time and Dynamic Address Table......................................... 17
5.3.3 Static MAC Address Table...................................................................... 18
5.3.4 Filtering MAC Address Table ................................................................ 18

V
5.3.5 Dynamic Binding...................................................................................... 18
5.3.6 Ping ............................................................................................................... 19
5.4 VLAN Setting ..................................................................................................... 19
5.4.1 VLAN Mode ................................................................................................ 19
5.5 Port Trunking..................................................................................................... 20
5.6 Priority Setting.................................................................................................. 20
5.6.1 Priority Mode............................................................................................. 20
5.6.2 Port-Based Priority................................................................................... 20
5.6.3 Port Default Priority ................................................................................ 21
5.6.4 802.1p Priority........................................................................................... 21
5.7 Port Mirroring.................................................................................................... 21
5.8 Virtual Cable Test.............................................................................................. 21
Chapter 6 WEB Management————————————— 22
6.1 Overview............................................................................................................. 22
6.2 Connecting to the Device............................................................................. 22
6.2.1 Getting Started ......................................................................................... 22
6.2.2 Login the Switch....................................................................................... 25
6.3 Setting the Device ........................................................................................... 25
6.3.1 System Setting .......................................................................................... 28
6.3.2 Port Setting ................................................................................................ 30
6.3.3 Network Setting ....................................................................................... 35
6.3.4 VLAN Setting.............................................................................................. 41
6.3.5 Port Trunking............................................................................................. 45
6.3.6 Priority Setting.......................................................................................... 46
6.3.7 Port Mirroring............................................................................................ 48
6.3.8 Virtual Cable Test...................................................................................... 49
Appendix A Troubleshooting ————————————— 50
Appendix B Table of Factory Defaults —————————— 51
Appendix C Table of Function Dierences of Switch Family —53
Appendix D Hardware Specications —————————— 54
Appendix E Technical Support ————————————— 55
Contents

01
Gigabit Uplink Web Smart Switch
Introduction


The TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Gigabit Uplink Web
Smart Switch is compliant with the IEEE802.3 Ethernet protocols. The EIA-standardized
framework and smart configuration capacity can provide flexible solutions for variable
scale of networks.
This switch family is equipped with powerful management interface, via which system,
port, network, VLAN, truck and priority can be configured.
The TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TLSL2452WEB Gigabit Uplink
Web Smart Switch provides 8/16/24/48 10/100Mbps Fast Ethernet ports, 1/1/2/2
10/100/1000Mbps Gigabit Ethernet ports and 1/1/2/2 SFP ports respectively, which
extends the connecting area and increases the networking flexibility.

Compliant with IEEE802.3, IEEE802.3u, IEEE802.3ab and IEEE802.3z Standards
¾
IEEE 802.3x flow control for full-duplex
¾
Back pressure flow control for half-duplex
¾
Store-and-Forward switching method
¾
Support N-Way adaptive mode
¾
Support up 200 meters of Cat. 5 cables at the transmission speed of 10Mbps
¾
Support MAC address table of 8K entries
¾
Support MAC address learning and aging time
¾
Support port-based VLAN and IEEE802.1Q tag VLAN
¾
Support trunks
¾
Support management via WEB browser
¾
Support port-based priority and IEEE 802.1p priority
¾
Support static MAC address and filtering MAC address
¾
Support dynamic binding of MAC address
¾
Support port security, storm control and port monitoring
¾
Support virtual cable test
¾
Support static switch IP address and dynamic switch IP address through DHCP client
¾
Support system upgrading, configuration uploading and backup through TFTP server
¾

02
Gigabit Uplink Web Smart Switch
Introduction

Front Panel

The front panel of TL-SL2210WEB is shown as the following figure.
13
57
2468GIGA SFP
10/100Mbps 10/100/1000Mbps 1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
Front Panel of TL-SL2210WEBFigure 1-1
The front panel of TL-SL2218WEB is shown as the following figure.
10 12 14 16
911 13 15
1357
2468
SFP
16+2G Gigabit Web-Smart Switch
Power
1000Mbps
246810 12 14 16
1357911 13 15
Link/Act
GIGA
System
TL-SL2218WEB
GIGA
Link/Act
RESET
Link
Act
100Mbps
R
Front Panel of TL-SL2218WEBFigure 1-2
The front panel of TL-SL2428WEB is shown as the following figure.
GIGA1
GIGA2
911131513
57 17 19 21 23
10 12 14 16
24
6818 20 22 24
SFP 1
Power
13
57911131517192123
GI G A 1
24
6810 12 14 16 18 20 22 24
GI G A 2
System
100M 1000M
SFP 2
ActLink
SFP 2
SFP 1
Reset
TL-SL2428WEB
24+4G Gigabit Web-Smart Switch
Front Panel of TL-SL2428WEBFigure 1-3
The front panel of TL-SL2452WEB is shown as the following figure.
RESET
Power
System
48+4G Gigabit Web-Smart Switch
TL-SL2452WEB
SFP 1
SFP 2
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48246810 12 14 16 18 20 22 24 25 26 27 281357911131517192123 GIGA1 GIGA2
246810 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
GIGA2
27 29 31 33 35 37 39 41 43 45 47251 357911131517192123
GIGA1
SFP1 SFP2 Link/Act
R
Front Panel of TL-SL2452WEBFigure 1-4
10/100/1000Mbps RJ45 Port
SFP Port
LEDs
10/100Mbps RJ45 Port
RESET
LEDs
RESET
10/100Mbps RJ45 Port
10/100/1000Mbps RJ45 Port
SFP Port
LEDs
SFP Port
10/100/1000Mbps RJ45 Port
RESET
10/100Mbps RJ45 Port
LEDs
10/100Mbps RJ45 Port
10/100/1000Mbps RJ45 Port
SFP Port
Reset

03
Gigabit Uplink Web Smart Switch
RESET
Press this button for three seconds to reset the software setting back to factory
default setting.
LEDs
LED Status Indication
Power On The Switch is powered on
Off The Switch is powered off or power supply is abnormal
System On The Switch works properly
Off The Switch works improperly
Link/Act
On A valid link is established on the port
Flashing Data is being transmitted or received. (SFP port has Link/
Act LED only and must connect to 1000Mbps device.)
Off No device is connected to the corresponding port
100Mbps
On The corresponding port is running at 100Mbps
Off There is no device linked to the corresponding port or the
port is running at 10Mbps
1000Mbps
On The corresponding port is running at 1000Mbps
Off There is no device linked to the corresponding port or the
port is running at 100Mbps
Port Feature
Model 10/100Mbps RJ45 Port 10/100/1000Mbps RJ45 Port SFP Port
TL-SL2210WEB 8 1 1
TL-SL2218WEB 16 1 1
TL-SL2428WEB 24 2 2
TL-SL2452WEB 48 2 2
10/100Mbps RJ45 Port
Designed to connect to the device with the bandwidth of 10Mbps or 100Mbps. Each
port has a corresponding Link/Act and 100Mbps LED.
10/100/1000Mbps RJ45 Port
Designed to connect to the device with the bandwidth of 10Mbps, 100Mbps or
1000Mbps. It has a corresponding Link/Act and 1000Mbps LED.
SFP Port
Designed to install SFP module. It has a corresponding Link/Act LED.
Introduction

04
Gigabit Uplink Web Smart Switch
Rear Panel

The rear panel of TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB is
shown as the following figure.
Rear PanelFigure 1-5
Power Socket
Connect the female connector of the power cord here, and the male connector to
the AC power outlet. Please make sure the voltage of the power supply meets the
requirement of the input voltage.
Caution: Please use the provided power cord.
Introduction
Power Socket

05
Gigabit Uplink Web Smart Switch


Make sure that the package contains the following items. If any of the listed items is
damaged or missing, please contact your distributor.
This User Guide
One Gigabit Uplink Web Smart
Switch
One AC Power Cord
Two Mounting Brackets and the
Fittings
13
5 7
2468GIGA SFP
10/100Mbps
10/100/1000Mbps
1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R

To avoid any device damage and bodily injury caused by improper use, please observe
the following rules.
Safety Precautions

Keep the power off during the installation.

Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good

skin contact and is well grounded.
Use only the power cord provided with the Switch.

Make sure that the supply voltage matches the specifications indicated on the rear

panel of the Switch.
Ensure the vent hole is well ventilated and unblocked.

Do not open or remove the cover of the Switch.

Before cleaning the device, cut off the power supply. Do not clean it by the waterish

cloth, and never use any other liquid cleaning method.
Installation

06
Gigabit Uplink Web Smart Switch
Site Requirements

To ensure normal eperation and long service life of the device, please install it in an
environment that meets the requirements described in the following subsection.
Temperature/Humidity
ȭ
ȭ
13
57
2468GIGA SFP
10/100Mbps 10/100/1000Mbps 1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
Please keep a proper temperature and humidity in the equipment room. Too high/low
humidity may lead to bad insulation, electricity leakage, mechanical property changes
and corrosions. Too high temperature may accelerate aging of the insulation materials
and can thus significantly shorten the service life of the device. For normal temperature
and humidity of the device, please check the following table.
Environment Temperature Humidity
Operating 0℃~ 40℃10% ~ 90%RH Non-condensing
Storage -40℃~ 70℃5% ~ 90%RH Non-condensing
Clearness
13
57
2468GIGA SFP
10/100Mbps 10/100/1000Mbps 1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
The dust accumulated on the Switch can be absorbed by static electricity and result
in poor contact of metal contact points. Some measures have been taken for the
device to prevent static electricity, but too strong static electricity can cause deadly
damage to the electronic elements on the internal circuit board. To avoid the effect of
static electricity on the operation of the Switch, please attach much importance to the
following items:
Dust the device regularly, and keep the indoor air clean.

Keep the device well grounded and ensure static electricity has been transferred.

Electromagnetic Interference
13
57
2468GIGA SFP
10/100Mbps 10/100/1000Mbps 1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
Electronic elements including capacitance and inductance on the device can be affected
by external interferences, such as conducted emission by capacitance coupling,
inductance coupling, and impedance coupling. To decrease the interferences, please
make sure to take the following measures:
Use the power supply that can effectively filter interference from the power grid.

Installation

07
Gigabit Uplink Web Smart Switch
Keep the device far from high-frequency, strong-current devices, such as radio

transmitting station.
Use electromagnetic shielding when necessary.

Lightening Protection
13
57
2468GIGA SFP
10/100Mbps 10/100/1000Mbps 1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
Extremely high voltage currents can be produced instantly when lightning occurs and the air
in the electric discharge path can be instantly heated up to 20,000℃. As this instant current
is strong enough to damage electronic devices, more effective lightning protection measures
should be taken.
Ensure the rack and device are well earthed.

Make sure the power socket has a good contact with the ground.

Keep a reasonable cabling system and avoid induced lightning.

Use the signal SPD (Surge Protective Device) when wiring outdoor.

Note: For detailed lightning protection measures, please refer to Chapter 3
Lightning Protection.
Installation Site
S
13
57
2468GIGA SFP
10/100Mbps 10/100/1000Mbps 1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
When installing the device on a rack or a flat workbench, please note the following
items:
The rack or workbench is flat and stable, and sturdy enough to support the weight

of 5.5kg at least.
The rack or workbench has a good ventilation system. The equipment room is well

ventilated.
The rack is well grounded. Keep the power socket less than 1.5 meters away from

the device.
Installation

08
Gigabit Uplink Web Smart Switch

Phillips screwdriver

ESD-preventive wrist wrap

Cables

Note: These tools are not provided with our product. If needed, please self purchase
them.

Desktop Installation

To install the device on the desktop, please follow the steps:
Set the device on a flat surface strong enough to support the entire weight of the1.
device with all fittings.
Remove the adhesive backing papers from the rubber feet.2.
Turnover the device and attach the supplied rubber feet to the recessed areas on3.
the bottom at each corner of the device.
1 3 5 7
2 4 6 8 G I G A SF P
10 / 100 M bp s
10/100/1000Mbps
1000Mbps
1 2 3 4 5678
TL-SL2210WEB
RES E T
8 + 2 G Web- Smart S w i tc h
Powe r
100M
Link
Act
Sy s t e m
1000M
GIGA
Lin k /Act
Link/ A ct
R
Feet
Bottom of the Device
Notch
Desktop InstallationFigure 2-1
Rack Installation

To install the device in an EIA standard-sized, 19-inch rack, follow the instructions
described below:
Check the grounding and stability of the rack.1.
Secure the supplied rack-mounting brackets to each side of the device with supplied2.
screws, as illustrated in the following figure.
Installation

09
Gigabit Uplink Web Smart Switch
13
5 7
2468GIGASFP
10/100Mbps
10/100/1000Mbps
1000Mbps
12345678
TL-SL2210WEB
RESET
8+2G Web- SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
Rack-mounting Bracket
Screw
Bracket InstallationFigure 2-2
After the brackets are attached to the device, use suitable screws (not provided) to3.
secure the brackets to the rack, as illustrated in the following figure.
1 3 57
2468GIGASFP
10/100Mbps
10/100/1000Mbps
1000Mbps
1 2 345678
TL-SL2210WEB
RESET
8+2GWeb-SmartSwitch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
Rack
Rack InstallationFigure 2-3
Caution:
Please set 5~10cm gaps around the device for air circulation.

Please avoid any heavy thing placed on the device.

Please mount devices in sequence from the bottom to top of the rack and ensure a

certain clearance between devices for the purpose of heat dissipation.
Installation

10
Gigabit Uplink Web Smart Switch


In the actual network environment, you may need cable outdoors and indoors, and
the requirements for cabling outdoors and indoors are different. A reasonable cabling
system can decrease the damage of induced lightning to devices.
Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors,
please use a signal lightning arrester.
Requirements for Cabling Outdoors

Aerial cabling without safeguard is not allowed.

It’s not allowed cabling down the building to connect network devices in different

floors.
Outdoor cables should be buried and paved to the indoor through basement. A

piece of steel wire should be paved underground along the pipe and connected to
the lightning protection terminal of the building for shielding. Before connecting the
cable to the device, install a signal lightning arrester on the corresponding port.
When an aerial cable is set up, the cable should be through a metal pipe (15m long

at least) before coming into the building. The two ends of this metal pipe should
be grounded. Before connecting the cable to the device, install a signal lightning
arrester on the corresponding port.
It’s not necessary to pave STP cables through pipes. The shielded layer of STP cable

should be well grounded. Before connecting the cable to the device, install a signal
lightning arrester on the corresponding port.
Lightning Protection

11
Gigabit Uplink Web Smart Switch
Requirements for Cabling Indoors

When cabling indoors, keep a certain distance away from the devices that may cause
high-frequency interferences, such as down-conductor cable, powerline, power
transformer and electromotor.
The main cable should be paved in the metal raceway of the access shaft. When

cabling, keep the loop area formed by the cable itself as small as possible.
Requirements for the distance between Ethernet cable and other pipelines are

shown in the table.
Other Pipelines
Ethernet Cable
Min Parallel Net Length L
(mm)
Min Parallel-overlapping
Net Height H (mm)
Down-conductor 1000 300
PE 50 20
Service pipe 150 20
Compressed air pipe 150 20
Thermal pipe (not wrapped) 500 500
Thermal pipe (wrapped) 300 300
Gas pipe 300 20
The two diagrams below demonstrate parallel net length and parallel-overlapping net
height.
Note: The above minimum net length/height is required when metal raceway is not
used. If any requirements cannot be met, you can add a steel tube or metal raceway
for shielding.
Requirements for the distance between Ethernet cable and high-power electric

devices are in following tables.
Cable Pave Way
Min Parallel
Length
(mm)
<2kVA
powerline
Parallel cabling 130
One is in the grounded metal raceway or metal pipe 70
The both are in the grounded metal raceway or metal pipe 10
Lightning Protection

12
Gigabit Uplink Web Smart Switch
2~5kVA
powerline
Parallel cabling 300
One is in the grounded metal raceway or metal pipe 150
The both are in the grounded metal raceway or metal pipe 80
>5kVA
powerline
Parallel cabling 600
One is in the grounded metal raceway or metal pipe 300
The both are in the grounded metal raceway or metal pipe 150
Device Min Distance (m)
Switch case 1.00
Transformer room 2.00
Elevator tower 2.00
Air-conditioner room 2.00
 
Connecting the device to ground is to quickly release the lightning over-voltage and
over-current of the device, which is also a necessary measure to protect the body from
electric shock.
In different environments, the device may be grounded differently. If the device is
installed in the normal environment, the device can be grounded via the PE (Protecting
Earth) cable of the AC power supply as shown in the following figure.
Connecting to the GroundFigure 3-1
Note:
The figure is to illustrate the application and principle. The power plug you get from

the package and the socket in your situation will comply with the regulation in your
country, so they may differ from the figure above.
If you intend to connect the device to the ground via the PE (Protecting Earth) cable

of AC power cord, please make sure the PE (Protecting Earth) cable in the electrical
outlet is well grounded in advance.
Lightning Protection

13
Gigabit Uplink Web Smart Switch


Please connect the Ethernet port of the Switch to the network devices by RJ45 cables
as the following figure shown.
1 3 57
2468GIGASFP
10/100Mbps
10/100/1000Mbps
1000Mbps
12345 6 78
TL-SL2210WEB
RESET
8+2GWeb-Sm artSwi
tch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
1
678
TL-SL2210WEB
RESET
8+
2GWeb-S
1000M
GIGA
Link/Act
Connecting the RJ45 PortFigure 4-1

Connect the SFP port to a SFP module. If an SFP transceiver(purchased separately)
is installed in a slot and has a valid link on the port, the associated RJ45 port will be
disabled and cannot be used.
1 3 57
2 4 68 GIG A SF P
10/100Mbp s
10/100/1000Mbps
1000Mbps
12345678
TL-SL2210WEB
RESET
8+2GWeb-Smart Switch
Power
100M
Link
Act
System
1000M
GIGA
Link/Act
Link/Act
R
8GIGASFP
10/100/1000Mbps
1000Mbps
Link/Act
Inserting the SFP ModuleFigure 4-2
Note: SFP module supports hot-plugging, plug the SFP module into the SFP port
and the switch can identify it automatically. The SFP port must connect to 1000Mbps
device.
Connection
RJ45 Port
RJ45 Cable
SFP Port
SFP Module