TrailFX 5059XH User manual

www . T r a il F X . c om
Page 1of 3 Rev 052518
Important Safety Information
CAUTION - Before driving, ensure that the hood shield is properly secured to vehicle.
Do not use automatic “brush-style” car washes.
Do not use cleaning solvents of any kind.
Periodically check all components for tightness.
NOTE: Actual product may vary from illustration.
Tools Required
Preparation Before Painting / Installation
•A trial fit is recommended to ensure proper positioning and fit.
•Check fit of parts before painting as we will not accept the return of modified or painted parts.
•Wash and dry your vehicle to remove any debris and/or dirt from the installation area.
Hood Protector
5059XH
Fit: 2011 - 2016 Ford F-250/350/450/550 Super Duty
Qty
Description
01
Hood Protector
01
Alcohol Pad
Qty
Description
01
Hardware Kit
PHILLPS SCREW DRIVER REQUIRED FOR INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
30-60 min
CUTTING NOT
REQUIRED
DRILLING NOT
REQUIRED
[e-mail]
1 866 638 4870
LIMITED LIFETIME

www . T r a il F X . c om
Page 2of 3 Rev 052518
INSTALLATION STEPS
Fig 1
Fig 2
1. Before starting installation insure that there is an even gap of at least 5/8”(16mm) between the hood
and the grill across the entire length of the hood.(Fig.1) ,If the gap need to be adjusted, Slightly loosen
the adjustment bolts located at the point shown(Fig.2) and gently nudge the grill until the correct gab
is achieved. Retighten the bolt.
2. Lift the hood and remove any dirt or debris. Clean the area under the hood with the alcohol pad where
the tape is to adhere.
3. Remove the red backing from the adhesive tape on the hood protector.
4. Insert the grommet nuts into the slots in the hood where the outer tabs of the hood protector will
mount.
5. Center the hood protector and fasten the outer mounting tabs to the hood .Using screws with washers
going into the grommet nuts you placed in the hood. And apply firm pressure to securely adhere them
to the underside of the hood.

www . T r a il F X . c om
Page 3of 3 Rev 052518
PRODUCT CARE
 Periodically check the productto ensure allfastenersaretightandcomponents are intact.
 Cleaning yourhood protector-use only soapy water anda soft cloth. Never use paper towels, petroleum product, or solvents to cleanyour hood
protector.
Check out these other TrailFX Products!! www.TrailFX.com
FAQ’s
1. Mounting Bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver /
Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
2. Products are thumping / rattling after installation.
Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular
grease between the metal to metal contact surfaces.
3. Missing / Excess Hardware.
Recheck hardware count as per the part list.
4. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time
of purchase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of
fitness for a particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product
at our option, when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this
product voids the warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically
excludes liability for any incidental or consequential loss or damage.