Car Solutions QHI-LVTX-LR-3G User manual

Car-Solutions.com
[email protected]
www.car-solutions.com

•Specification
Car Compatibility :
8” monitor
RANGE ROVER JEEP, DISCOVERY SPORTS, JAGUAR
F_PACE
10” monitor
RANGE ROVER EVOQUE, RANGE ROVER SPORT
DISCOVERY, JAGUAR XJ
Components : Interface* 1ea
Multimedia interface Input/output spec
Input : HDMI*1, Analog RGB*1, A/V*1,
CVBS(Rear view camera)*1, CVBS(Front camera)*1
Output : To LCD*1
Power spec
Input power : 8VDC ~ 18VDC
consumption : 5WATT
Switch input mode
External video sources skip function : able to control input
videos on and off via DIP switches.
Able to switch videos via the remote, button switch, and
original buttons.
Able to detect the rear view camera (back up camera)
via Lamp or CAN.
2
•Features
Able to output high resolution video via HDMI input
Control external videos sources (DVD, DTV) via Multi Media
Touch
Adjust external videos screen position
The improved Screen Display (User Friendly Interface)
Switch modes via original OEM button
Supply power for rear view camera (Back up camera)
Assist your parking via Dynamic PAS(Parking Assistance
System), PDC(Parking Distance Control), moving parking line
according movement of steering wheel
Car-Solutions.com
[email protected]
www.car-solutions.com

3
•Product exterior
Length-90mm
Height-18mm
Width-140mm
•Components
AV * 1ea
(HAVCAB0056)
LCD * 1ea
(HLCDCA0049)
RGB * 1ea
(HRGBCA0013)
BUTTON * 1ea
(HARETC0001)
IR * 1ea
(HIRCAB0002)
Remote * 1ea
(REMOTE0001)
POWER * 1ea
(HPOWER0190)
MULTI * 1ea
(HARETC0240)
REAR * 1ea
(HIRCAB0002)
Car-Solutions.com
[email protected]
www.car-solutions.com

PIN FUNCTION Dip S/W
1 RGB MODE OFF : DISPLAY RGB
ON : SKIP RGB
2 HDMI MODE OFF : DISPLAY HDMI
ON : SKIP HDMI
3 AV1 MODE OFF : DISPLAY AV1
ON : SKIP AV1
4 AV2 MODE OFF : DISPLAY AV2
ON : SKIP AV2
5 Refer to dip switch setting below
6 NO USE(OFF)
7 REAR CAMERA MODE OFF : OEM REAR CAMERA
ON : EXTERNAL REAR CAMERA
8 Refer to dip switch setting below
※ ON : DOWN / OFF : UP
4
•DIP SWITCH
※Please make sure to disconnect the power cable of the interface and
reconnect the power cable again to apply the dip switch setting whenever
changing DIP switch. Otherwise, DIP switch setting will not be applied.
Settings
Car Model
MONITOR CAR MODEL DIP SW
8" 10" TYPE1 TYPE2 Evoque Jaguar
XE DIP #5 DIP #8
RANGE ROVER JEEP ●not used ON ON
RANGE ROVER
EVOQUE ●●OFF OFF
RANGE ROVER
SPORT ●●OFF OFF
DISCOVERY ●●OFF OFF
DISCOVERY SPORTS ●●ON OFF
JAGUAR XJ ●●OFF OFF
JAGUAR XE ●●OFF OFF
JAGUAR F_PACE ●●ON OFF
Car-Solutions.com
[email protected]
www.car-solutions.com

5
•REMOTE CONTROL SETTING
Key FUNCTION
POWER & PIP NO USE
MENU Activate Factory menu
OK Selection, changing image display
▲Up
▼Down
◀Left( Access the factory mode
if the button is pressed for 2 seconds)
▶Right (Activate factory reset
if the button is pressed for 2 seconds)
Car-Solutions.com
[email protected]
www.car-solutions.com

6
•Factory setting
Adjust a current screen position and size.
PAS TYPE : Select type of parking guide line
- NOT USED : No use parking guide line
- PAS ON : Selecting Dynamic parking guide line
- PAS OFF : Selecting fixed parking guide line
PAS SETUP : Adjusting the position of the parking guide line
REAR TYPE : Choose rear camera recognition.
- CAN : By connecting to “CAN” cable of the car gear, changing to
rear camera mode when shifting into reverse. (Connect “CAN”
cable of the power cable to the “CAN” cable of the car gear.)
- LAMP : By connecting to the rear lamp of the car, switch to rear
camera mode when shifting into rear. (Connect “Rear-C” cable of
the power cable to the rear lamp of the car.)
SAFE ENABLE : If it is enable, HDMI, RGB, and A/V mode doesn’t show up
while driving. (Default : OFF)
RADAR ENABLE : Setting up parking distance alarm sensor. (ON/OFF)
<H-POSITION> <V-POSITION>
Adjust rear view camera setting.
H-POSITION : Move display horizontally
V-POSITION : Move display vertically
BRIGHTNESS : Adjust brightness of screen
CONTRAST : Adjust contrast of screen
Car-Solutions.com
[email protected]
www.car-solutions.com

7
•Factory setting
Navigation & Car model setting up
NAVI MODEL : Setting for RGB navigation
(Default, Q-roi RGB, WP9230,
HDMI(WVGA))
HDMI MODEL : Setting for HDMI navigation
(Q-roi RGB, WP9320, HDMI,
PAPAGO)
CAR MODEL : Selection for car model
(TYPE1, TYPE2)
AVOUT SELECT :Selecting background sound
through car AUX. HDMI1, HDMI2,
AV)
MODE BUTTON :Selecting mode button
(NAVI, HOME)
※ Only 8 inch monitor is supported
FACM FUNC :ON –Use front camera
OFF –Do not use front camera
Other options
CALIBRATE : Able to calibrate touch screen
REMOTE SELECT : Able to use remote control on
DVD, DTV by selecting “User”
after IR memory is registered.
(Default, User)
AV1 REMOTE OSD : AV1 multimedia OSD setting
AV2 REMOTE OSD : AV2 multimedia OSD setting
IR MEMORY : Register IR memory of Remote
control for DTV, DVD
FACTORY RESET : FACTORY mode reset
System version information
Car-Solutions.com
[email protected]
www.car-solutions.com

※ Able to switch modes via HOME or NAV button of car monitor
※ Set up the “mode button” setting on the factory mode
8
•OEM button(8inch)
•OEM button(10.2inch)
※ Press the voice button long on the steering wheel to change the mode
Car-Solutions.com
[email protected]
www.car-solutions.com

9
OEM LCD Cable
•Installation Diagram
HDMI
NAVI BOX
RGB
NAVI BOX
※ HDMI NAVI has to be connected
to HDMI-1
OEM
monitor
Command
Supplied LCD Cable
AV1 AV2 AV3
REAR C
Audio L
Audio R
AV/OUT Video
•LCD cable (8inch, 10inch)
OEM LVDS cable
Supplied
LVDS cable
※ Remove the white cable from the command
and connect this cable to “LVDS IN” of the
interface
※ Supplied LVDS
cable is connected to
the command
ACC
CAN2-L(OUT)
GND
CAN2-H(OUT)
CAN1-L(IN)
CAN1-H(IN)
LIN
Car-Solutions.com
[email protected]
www.car-solutions.com

10
•CAN Connection(10.2inch)
※ Headunit location
- JAGUAR :
Trunk inside
- LAND ROVER :
Below the passenger’s seat
ACC
CAN2-L(OUT)
GND
CAN2-H(OUT)
CAN1-L(IN)
CAN1-H(IN)
LIN
Power cable
Find the square connector from the
back side of the command
Cut and wire cables as shown on the left
18
17
16
•CAN connection(8inch)
<OEM SINGLE CAN> <OEM DUAL CAN>
ACC
CAN2-L(OUT)
GND
CAN2-H(OUT)
CAN1-L(IN)
CAN1-H(IN)
LIN
Supplied Power
cable
ACC
CAN2-L(OUT)
GND
CAN2-H(OUT)
CAN1-L(IN)
CAN1-H(IN)
LIN
Supplied Power
cable
CAN1-H(IN)→Green+Purple
CAN1-L(IN) →Grey+Purple
CAN1-H(IN)→Purple+Grey
CAN1-L(IN) →Blue+Grey
CAN2-H(OUT)→Green+Purple
CAN2-L(OUT)→Grey+Purple
OEM cable Supplied
power cable
No 16 pin
Purple+Light Purple CAN1-L(IN)
No 17pin
Green+Purple CAN1-H(IN)
No 18pin
Yellow+Grey LIN
Car-Solutions.com
[email protected]
www.car-solutions.com

11
•Q-ROI RGB -Uart Touch
Another side of the wire shall
be connected to “IR-NAVI”
from RGB cable of the
interface
Connect a wire to the first pin on the right
It’s Q-ROI RGB Uart wire.
Car-Solutions.com
[email protected]
www.car-solutions.com

12
Q. I cannot change mode
A. Check connection of Ground cable and IR Cable. Check LED lamp
is on, if not check connection of POWER cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V
sources connected are working well. (Second
lamp indicates AV sources connected works well.) Check interface
connection has been done well.
Q. Displayed image color is not proper (too dark or unsuitable color)
A. Press ▶button on the remote control for 2 seconds and check how
it goes, if it does not work, inform to manufacturer.
Q. I cannot watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Set mode not appear
A. Check DIP Switch.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps
on, inform to manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to
manufacturer.
Q. If the original screen is shown half only after using the handle button
for running the PIP function.
A. This is not because of defect but incorrect setting up. Make sure to
set up the original monitor function as “split screen”
Q. If no image is shown on screen after connecting CAN wire with Park
gear.
A. Go on the “FACTORY MODE”, check “UTIL-Rear Select”. If “LAMP”,
change the setting as “CAN” with the remote control. (※when
connecting Rear-C wire of LAMP power cable to Backup lights, Setting
should be like this / CAN : if controlling rear camera with CAN wire)
•Trouble shooting
Car-Solutions.com
[email protected]
www.car-solutions.com