Trane Tracer Concierge BMTC015ABC012000 User manual

SAFETY WARNING
Only qualified personnel should install and service the equipment. The installation,
starting up, and servicing of heating, ventilating, and air-conditioning equipment
can be hazardous and requires specific knowledge and training. Improperly
installed, adjusted or altered equipment by an unqualified person could result in
death or serious injury. When working on the equipment, observe all precautions in
the literature and on the tags, stickers, and labels that are attached to the
equipment.
BAS-SVN141E-EN
December 2023
Model Numbers: BMTC015ABC012000 BMTC030ABC000000
BMTC030ABC012000 BMTC030ABC002100
BMTC060ABC012000 BMTC060ABC002100
Installation Instructions
Tracer Concierge®System for
Small Buildings
Pre-Packaged Control Panel and Display

©2023 Trane BAS-SVN141E-EN
Introduction
Read this manual thoroughly before operating or servicing this unit.
Warnings, Cautions, and Notices
Safety advisories appear throughout this manual as required. Your personal safety and the
proper operation of this machine depend upon the strict observance of these precautions.
Important Environmental Concerns
Scientific research has shown that certain man-made chemicals can affect the earth’s naturally
occurring stratospheric ozone layer when released to the atmosphere. In particular, several of
the identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine,
Fluorine and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon
(HCFCs). Not all refrigerants containing these compounds have the same potential impact to
the environment. Trane advocates the responsible handling of all refrigerants.
Important Responsible Refrigerant Practices
Trane believes that responsible refrigerant practices are important to the environment, our
customers, and the air conditioning industry. All technicians who handle refrigerants must be
certified according to local rules. For the USA, the Federal Clean Air Act (Section 608) sets
forth the requirements for handling, reclaiming, recovering and recycling of certain refrigerants
and the equipment that is used in these service procedures. In addition, some states or
municipalities may have additional requirements that must also be adhered to for responsible
management of refrigerants. Know the applicable laws and follow them.
The three types of advisories are defined as follows:
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION Indicates a potentially hazardous situation which, if not avoided, could result in
minor or moderate injury. It could also be used to alert against unsafe practices.
NOTICE Indicates a situation that could result in equipment or property-damage only
accidents.
WARNING
Proper Field Wiring and Grounding Required!
Failure to follow code could result in death or serious injury. All field wiring MUST
be performed by qualified personnel. Improperly installed and grounded field wiring
poses FIRE and ELECTROCUTION hazards. To avoid these hazards, you MUST
follow requirements for field wiring installation and grounding as described in NEC
and your local/state/national electrical codes.

BAS-SVN141E-EN 3
Introduction
Copyright
This document and the information in it are the property of Trane and may not be used or
reproduced in whole or in part, without the written permission of Trane. Trane reserves the right
to revise this publication at any time and to make changes to its content without obligation to
notify any person of such revision or change.
Trademarks
All trademarks referenced in this document are the trademarks of their respective owners.
Revision History
• Updated the image and model number information on the front cover.
• Updated Packaged contents table and Internal View image in Step 1: Verify Package
Contents.
• Updated Step 2: Install Symbio™ 700.
• Added Universal inputs and Analog outputs tables in Step 3: Install the Symbio™ 500
RTU/HP and Air-Fi®Wireless for Non-Trane RTUs.
• Updated Setup Wizard image in Step 9: Display Setup.
WARNING
Personal Protective Equipment (PPE) Required!
Failure to wear proper PPE for the job being undertaken could result in death or
serious injury. Technicians, in order to protect themselves from potential electrical,
mechanical, and chemical hazards, MUST follow precautions in this manual and on
the tags, stickers, and labels, as well as the instructions below:
• Before installing/servicing this unit, technicians MUST put on all PPE required for
the work being undertaken (Examples; cut resistant gloves/sleeves, butyl gloves,
safety glasses, hard hat/bump cap, fall protection, electrical PPE and arc flash
clothing). ALWAYS refer to appropriate Safety Data Sheets (SDS) and OSHA
guidelines for proper PPE.
• When working with or around hazardous chemicals, ALWAYS refer to the
appropriate SDS and OSHA/GHS (Global Harmonized System of Classification
and Labeling of Chemicals) guidelines for information on allowable personal
exposure levels, proper respiratory protection and handling instructions.
• If there is a risk of energized electrical contact, arc, or flash, technicians MUST put
on all PPE in accordance with OSHA, NFPA 70E, or other country-specific
requirements for arc flash protection, PRIOR to servicing the unit. NEVER
PERFORM ANY SWITCHING, DISCONNECTING, OR VOLTAGE TESTING WITHOUT
PROPER ELECTRICAL PPE AND ARC FLASH CLOTHING. ENSURE ELECTRICAL
METERS AND EQUIPMENT ARE PROPERLY RATED FOR INTENDED VOLTAGE.
WARNING
Follow EHS Policies!
Failure to follow instructions below could result in death or serious injury.
• All Trane personnel must follow the company’s Environmental, Health and Safety
(EHS) policies when performing work such as hot work, electrical, fall protection,
lockout/tagout, refrigerant handling, etc. Where local regulations are more
stringent than these policies, those regulations supersede these policies.
• Non-Trane personnel should always follow local regulations.

4 BAS-SVN141E-EN
Table of Contents
Step 1: Verify Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 2: Install Symbio™ 700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 3: Install the Symbio™ 500 RTU/HP for Non-Trane RTUs . . . . . . . . . . . . . 9
Step 4: Install the Symbio™ 210 Bypass Damper . . . . . . . . . . . . . . . . . . . . . . . 10
Step 5: Install Tracer Concierge System Panel . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dimensions and Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Location and Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wiring High Voltage AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Install Enclosure Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 6: Field wired I/O (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 7: Mount the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 8: System Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 9: Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Step 10: Project Commissioning Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Agency Listing and Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

BAS-SVN141E-EN 5
Step 1: Verify Package Contents
Before proceeding with installing the Tracer System Panel, set up the unit controllers as
required, such as Symbio™ 700 (requires advanced board) and Air-Fi®Wireless Step 2,
Symbio 500 and Air-Fi Wireless Step 3, and Symbio 210 and Air-Fi Wireless Step 4.
Table 1. Packaged contents
Part Number Packaged Contents
BMTC030ABC000000 System Controller with 15 device license, no enclosure or WCI.
BMTC015ABC012000 System Controller with 15 device license, with enclosure and WCI.
BMTC030ABC012000 System Controller with 30 device license, with enclosure and WCI.
BMTC060ABC012000 System Controller with 60 device license, with enclosure and WCI.
BMTC030ABC002100 System Controller with 30 device license, with enclosure and VRF license,
no WCI.
BMTC060ABC002100 System Controller with 60 device license, with enclosure and VRF license,
no WCI.
Figure 1. Internal View
Outlets are provided for Tracer System
accessories including cellular router,
wifi router and the 10 in. display
Convenience outlet
for a laptop
Tracer System
Controller
Optional XM30: Outdoor
Air Temperature
Input Module
(ordered as an accessory)
Optional XM32:
Output Module
for lighting/exhaust
fan control
(ordered as an accessory)

6 BAS-SVN141E-EN
Step 2: Install Symbio™ 700
Step 2: Install Symbio™ 700
If applicable to this site, install the Symbio™700 rooftop / split system equipment and controls
and either BACnet MS/TP or Air-Fi®Wireless. In all cases, the Symbio 700 is factory installed
in the equipment along with the applicable adapter board. The connection between the Symbio
700 and adapter board is also completed in the factory. Use the screw terminals provided on
the Symbio 700 controller for BACnet MS/TP connection(s). Use the screw terminals provided
on the adapter board for connection to the Air-Fi®Wireless WCI for communicating
applications.
Important: Communication is enabled with the advanced version of the controller,
including BACnet and Air-Fi Wireless communication.
Figure 2. Symbio 700 and BACnet MS/TP wiring terminations
Important: Before applying power to the Air-Fi Wireless WCI (when applicable), power down
the Symbio 700 controller and equipment. Once the wiring connections between the WCI and
Symbio 700 adapter board are complete, apply power to the Symbio 700 equipment controller
and WCI together.

BAS-SVN141E-EN 7
Step 2: Install Symbio™ 700
Note: Ensure Air-Fi Wireless and zone sensors are addressed per the submittal.
There are several AHU/condenser pairing scenarios for Odyssey split systems. In some
cases, only a Symbio 700 controller and associated adapter board exist in the outdoor
condenser. In those cases, connect the Air-Fi Wireless WCI to the adapter board.
Note: The recommended installation for the WCI is indoors. As a result, install the necessary
wiring between the WCI and Symbio 700 adapter board. Refer to Figure 4.
In other scenarios, the relay board exists in the indoor AHU. In those cases, connect the Air-
Fi Wireless WCI to the relay board. Refer to Figure 5.
Figure 3. Symbio™ 700 and Air-Fi®wireless interface for precedent rooftop units
Figure 4. Symbio™ 700 and Air-Fi®wireless interface for odyssey split systems
without relay board

8 BAS-SVN141E-EN
Step 2: Install Symbio™ 700
Figure 5. Symbio 700 and Air-Fi wireless interface for odyssey split systems with
relay board

BAS-SVN141E-EN 9
Step 3: Install the Symbio™ 500 RTU/HP for Non-Trane RTUs
Step 3: Install the Symbio™ 500 RTU/HP for Non-
Trane RTUs
If required for this site, install the Symbio™ 500 RTU/HP and either BACnet MS/TP or Air-Fi®
Wireless on Non-Trane equipment. For more information, see Symbio 500 Pre-programmed
for RTU or Heat Pump (BMSY500ABA100011). The pre-defined point designations are
mentioned below.
Table 2. Analog inputs
Label Functions Detail
Al1 Space Temperature Local
10 KΩ@ 77°F (25°C) Thermistor
Al3 Return Air Temperature Local
Al4 Discharge Air Temperature
Al5 Outdoor Air Temperature Local
Al2 Space Temperature Setpoint Local 1 KΩpotentiometer
Table 3. Universal inputs
Label Functions Detail
Ul1 Outdoor Air Damper Position Feedback 2 to 10 Vdc
Ul2 Space CO2 Concentration Local 4 to 20 mA
Table 4. Binary inputs
Label Functions Detail
Bl1 Mechanical Heat/Cool Disable Input Open = Disable,
Closed = Normal
Bl2 Occupancy Input Open = Occupied,
Closed = Unoccupied
BI3 Supply Fan Status Open = Off, Closed = On
Table 5. Analog outputs
Label Functions Detail
AO1 Supply Fan Speed Command 0 to 10 Vdc
AO2 Outdoor Air Damper Command 2 to 10 Vdc
Table 6. Binary outputs
Label Functions T-stat Detail
BO1 Supply Fan Start Stop Command G
Binary Output ratings
BO1 to BO3 Relay: 0.5A @ 24 Vac pilot duty
BO4 to BO9 Triac: 0.5A @ 24 Vac resistive and pilot
duty
BO2 Not Used –
BO3 Ventilation Relay –

10 BAS-SVN141E-EN
Step 4: Install the Symbio™ 210 Bypass Damper
Note: Ensure Air-Fi Wireless and zone sensors are addressed per the submittal, where
appropriate.
Step 4: Install the Symbio™ 210 Bypass Damper
If required for this site, install the UC210 Bypass Damper and either BACnet MS/TP or Air-Fi
Wireless, as applicable. See the installation documentation. The point list below is for your
convenience.
Note: Ensure Air-Fi®Wireless and zone sensors are addressed per the submittal.
Addressing of the Wireless Communication Sensors (WCS) and Wireless Communication
Interface (WCI) determines which devices can communicate on an Air-Fi network. On all WCS
and WCI, the GRP and NET are set at 1and 1. When installing, confirm that these remain at
1 and 1.
BO4 Compressor 1 Command Y1
BO5 Compressor 2 Command Y2
BO6 Heat stage W1 Command W1
BO7 Heat stage W2 Command W2
B08 Reversing Valve Command O Off = Heating, On = Cooling
B09 Auxiliary Heat Command X
Table 7. I/O points
Location Function
Pressure Input Duct Static Pressure Local
AI3/DAT Discharge Air Temperature (Optional)
Actuator Damper Actuator
Figure 6. Air-Fi®addressing
Table 6. Binary outputs (continued)
Label Functions T-stat Detail

BAS-SVN141E-EN 11
Step 5: Install Tracer Concierge System Panel
On unit controllers, such as rooftop units, VAV boxes, and bypass dampers, set the rotary
address settings to unique numbers. Set the first to 002, and so on. It's helpful to be sequential
and not to skip numbers; however, skipping numbers will not cause problems. Duplicate
numbers will cause communication problems.
On WCS zone sensors, set:
• GRP and NET to 1 and 1
• Address the WCS to match the corresponding unit controller
To enter the WCS address settings, press and hold the address button for 3 seconds.
For more information, see Air-Fi Wireless Communication Sensor (WCS) Configuration
Instructions, X3964126001 that is shipped with each zone sensor.
Step 5: Install Tracer Concierge System Panel
Important: Do not power the display until instructed to do so in Installation Instructions.
Dimensions and Clearances
Figure 1 shows the internal enclosure dimensions and minimum clearances. Select a
mounting location that provides adequate space for the minimum clearance dimensions. Refer
to Figure 8 for external enclosure dimensions.
Figure 7. Unit controller rotary addressing
Figure 8. Press the address button

12 BAS-SVN141E-EN
Step 5: Install Tracer Concierge System Panel
Figure 9. Enclosure minimum clearances with cover
Figure 10. External dimensions
1
2
in
.
(305 mm)
3
6 in
.
(
914 mm
)
1
2
in
.
(
305 mm
)
2
4 in
.
(
610 mm
)
12 in.
(
305 mm
)
50 in. (1270 mm) Recommende
d
Knockout for 0.75 in.
(
19 mm
)
condui
t
Knockout for 50 in.
(
13 mm
)
condui
t
Knockouts for 1 in.
(
25 mm
)
and 0.75 in.
(
19 mm
)
condui
t
Knockout for 0.50 in.
(
13 mm
)
c
onduit (for AC wiring
)
3
.125 in.
(
80 mm
)
14.75 in
.
(
373 mm
)
2.25 in
(
56 mm
)
15
in
.
(
381 mm
)
5
.5 in
.
(
140 mm
)
13.25 in (337 mm
)
1
6
.
5
in.
(
418 mm
)

BAS-SVN141E-EN 13
Step 5: Install Tracer Concierge System Panel
Location and Mounting Guidelines
Location
The location should meet the following operating environment requirements and clearances:
Important: The Tracer Concierge System Panel enclosure must be installed indoors.
Trane recommends locating the enclosure:
• Where service personnel have easy access.
• In areas that restrict public access to minimize tampering or vandalism.
Mounting Instructions
Note: The internal enclosure panel comes with four (4) mounting holes.
1. Using the enclosure as a template, mark the location of the four (4) mounting holes on the
mounting surface to accommodate the supplied #10 screws and/or #10 wall anchors.
2. Set aside the enclosure and drill the marked location holes for the screws.
Note: Use wall anchors if the mounting surface is dry wall or masonry.
3. Secure the enclosure to the mounting surface with the enclosed #10 screws and #10 wall
anchors.
4. Remove the tie wraps that secure the modules to the DIN rail during shipping.
Wiring High Voltage AC Power
Read all WARNINGS, CAUTIONS, and NOTICES prior to wiring high-voltage AC power.
Table 8. Operating environment specifications
Temperature From 32°F to 122°F (0°C to 50°C)
Humidity 5 to 95% non-condensing
Power Requirements 120 Vac: 9A maximum, 1 phase, 60 Hz
Weight Mounting surface must be able to support 60 lb. (28
kg)
Dimensions 16 ½ in. × 14 ¾ in. × 5 ½ in.
(418 mm × 373 mm × 140 mm)
Installation U.L. 840: Category 3
Pollution U.L. 840: Degree 2
WARNING
Hazardous Voltage!
Failure to disconnect power before servicing could result in death or serious injury.
Disconnect all electric power, including remote disconnects before servicing.
Follow proper lockout/ tagout procedures to ensure the power can not be
inadvertently energized. Verify that no power is present with a voltmeter.

14 BAS-SVN141E-EN
Step 5: Install Tracer Concierge System Panel
To ensure proper operation of the controllers, install the power supply circuit in accordance with
the following guidelines:
• The panel must receive power from a dedicated power circuit. Failure to comply could
cause panel malfunctions.
• A disconnect switch for the dedicated power circuit must be near the panel, within easy
reach of the operator, and marked as the disconnecting device for the panel.
• Do not run input or output wires in the same conduit or wire bundle with high voltage wire
or 24 Vac wiring. Failure to comply could cause the controller to malfunction due to
electrical noise.
• Power wiring must comply with the National Electrical Code™ (NEC) and applicable
electrical codes.
• 120 Vac wiring requires three-wire service (Line, Neutral, Ground). Refer to Panel 10 for
terminal locations.
Note: The transformer voltage utilization range is 98 to 132 Vac (120 Vac nominal).
1. Lock open the supply-power disconnect switch.
2. At the top-right corner of the enclosure, remove the knockout for 0.50-inch (13 mm)
conduit.
3. Open or remove the enclosure door if it is already installed.
4. Inside of the enclosure at the top-right corner, remove the line voltage area cover plate.
5. Feed the 120 Vac power wire into the enclosure.
6. Using Figure 9, connect the line wire to the Lterminal.
7. Connect the neutral wire to the Nterminal.
8. Connect the green ground wire to the chassis ground screw.
Note: The ground wire should be continuous back to the circuit breaker panel.
WARNING
Proper Field Wiring and Grounding Required!
Failure to follow code could result in death or serious injury. All field wiring MUST
be performed by qualified personnel. Improperly installed and grounded field wiring
poses FIRE and ELECTROCUTION hazards. To avoid these hazards, you MUST
follow requirements for field wiring installation and grounding as described in NEC
and your local/state/national electrical codes.
NOTICE
Use Copper Conductors Only!
Failure to use copper conductors could result in equipment damage as the
equipment was not designed or qualified to accept other types of conductors.
WARNING
Hazardous Voltage!
Failure to follow instructions below could result in death or serious injury.
Always make sure to put the cover plate back in place before operating the
controller.

BAS-SVN141E-EN 15
Step 5: Install Tracer Concierge System Panel
9. Replace the cover plate.
10. On a field-supplied label, record the location of the circuit breaker panel and the electrical
circuit. Attach the label to the cover plate.
Install Enclosure Door
1. Unpack the door and check for any missing or damaged parts.
2. Position the door at a 90 degree angle from the enclosure, as shown below.
3. Align the hinge pegs on the door with the hinge holes on the enclosure and gently lower
the door until it rests securely in the hinge holes.
Figure 11. AC wiring
Figure 12. Installing the enclosure door

16 BAS-SVN141E-EN
Step 6: Field wired I/O (optional)
4. Verify that the door swings freely on the hinges and that the magnetic latches hold the door
securely when it is closed.
Step 6: Field wired I/O (optional)
The field I/O wiring is specific for each application.
Tracer Concierge Accessories required for field wired I/O include X13651537010 - XM30 I/O
Module (4 UI/AO) and/or X13651537010 - XM32 Module (4 Relays).
Step 7: Mount the Display
Note: The display is designed for conditioned indoor environments only.
The Philips display has an attached wall mounting plate as a standard.
Mount the display using the wall mounting plate with three screws, and anchors.
The Philips display also accommodates 75mm VESA bracket.
As part of the installation, connect the display to the Tracer Concierge system controller using
either an Ethernet hardwired connection to LAN port 2 on the system controller or through a
wireless (Wi-Fi) connection.
Refer to BAS-SVX074*-EN for additional information on setting up the Tracer 10-inch display.
Step 8: System Start-Up
Important: Ensure all equipment and Air-Fi®Wireless are powered and operating before
proceeding. This is because the network will be formed on power up of Tracer
System Controller.
Module
Rotary
Dial Terminals Name Notes
XM30 01 UI/AO 1 Outside Air
Temperature Thermistor
XM30 01 UI/AO 2 N/A Not used
XM30 01 UI/AO 3 N/A Not used
XM30 01 UI/AO 4 N/A Not used
XM32 02 BO1 XM32 Binary
Output 1
Must be wired as dry contact; used for lighting output or
other
(for example, exhaust fan)
XM32 02 BO2 XM32 Binary
Output 2
Must be wired as dry contact; used for lighting output or
other
(for example, exhaust fan)
XM32 02 BO3 XM32 Binary
Output 3
Must be wired as dry contact; used for lighting output or
other
(for example, exhaust fan)
XM32 02 BO4 XM32 Binary
Output 4
Must be wired as dry contact; used for lighting output or
other
(for example, exhaust fan)

BAS-SVN141E-EN 17
Step 9: Display Setup
1. Apply power to the panel.Close the supply power disconnect switch that was locked open
when connecting the 120 Vac Power Wires.
2. Press the power button on the System Controller. Watch the controller go through its LED
sequence ending with dancing dashes. See Figure 14 for power button location.
Note: The network automatically stays open 1 hour. After each Air-Fi®Wireless module
joins, the 1 hour timer starts over. If time expires, press the OPEN NET button on the
Air-Fi Wireless module to re-open the network.
Notes: For more details or troubleshooting information, see the
•Tracer Concierge®System Installation, Operation, and Maintenance (BAS-SVX074*-EN).
•Air-Fi® Wireless System Installation, Operation, and Maintenance (BAS-SVX40*-EN).
3. Connect the Ethernet cable for customer’s network to Ethernet Port 1.
Step 9: Display Setup
1. Power on the display by pressing the power button on the back of the display.
2. Follow the steps in the Setup wizard. See the Tracer Concierge®System Installation,
Operation, and Maintenance (BAS-SVX074*-EN) for details.
Figure 13. Power button

18 BAS-SVN141E-EN
Step 10: Project Commissioning Checklist
Step 10: Project Commissioning Checklist
Verify that hardware installation is complete:
Figure 14. Setup wizard
Verify the Concierge System Controller panel is attached to the wall and power is wired to it.
Verify System Controller Air-Fi®Wireless is addressed properly per the submittal and/or the
Air-Fi® Network Design Installation, Operation, and Maintenance (BAS-SVX55*-EN).
Verify the Ethernet Cable for the customer’s network is connected to System Controller
Ethernet Port 1 (if applicable).
Verify that any rooftop units with Air-Fi Wireless are connected and addressed properly per
the submittal and/or the Air-Fi® Network Design Installation, Operation, and Maintenance
(BAS-SVX55*-EN).

BAS-SVN141E-EN 19
Notes
Agency Listing and Compliance
United States Compliance
(Enclosure and modules are UL Listed separately) UL Listed — UL 916 Energy Management Accessory
Canadian Compliance
Enclosure and modules are CUL Listed separately) CUL Listed — CSA C22.2 No. 205

Trane has a policy of continuous product and product data improvement and reserves the right to change design and
specifications without notice. We are committed to using environmentally conscious print practices.
Trane - by Trane Technologies (NYSE: TT), a global climate innovator - creates comfortable, energy efficient
indoor environments for commercial and residential applications. For more information, please visit
trane.com or tranetechnologies.com.
©2023 Trane
BAS-SVN141E-EN 09 Dec 2023
Supersedes BAS-SVN141D-EN (Sep 2021)