Transition Networks SISTF10xx-130-LR(T) User manual

User’s Guide
SISTF10xx-130-LR(T)
Stand-Alone Redundant Ring Industrial Switch
• Copper to Fiber
• Ethernet / Fast Ethernet
• 10Base-T / 100Base-TX to 100Base-FX
• Extended Temperature
• Hazardous Environment
* Typical maximum cable distance.
Actual distance is dependent upon the
physical characteristics of the network
installation.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .8
Cable Specifications . . . . . . . . . .10
Technical Specifications . . . . . . .12
Troubleshooting . . . . . . . . . . . . .14
Compliance Information . . . . . . .16
Part Number Ports 1, 2, & 3 - Copper
10Base-T/100Base-TX
Ports 4 & 5 - 100Base-FX
Duplex Fiber-Optic
SISTF1011-130-LR RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
SISTF1012-130-LR RJ-45
100 m (328 ft)*
ST, 1310 nm single mode
15 km (9.3 miles)*
SISTF1013-130-LR RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
SISTF1014-130-LR RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
15 km (9.3 miles)*
SISTF1011-130-LRT RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
SISTF1012-130-LRT RJ-45
100 m (328 ft)*
ST, 1310 nm single mode
15 km (9.3 miles)*
SISTF1013-130-LRT RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
SISTF1014-130-LRT RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
15 km (9.3 miles)*
Extended Temperature Models: -40°C to 75°C (-40°F to 167°F):
Standard Temperature Models: 0°C to 60°C (32°F to 140°F):
Transition Networks SISTF10xx-130-LR(T) redundant
ring industrial switch connects three (3) 10Base-T /
100Base-TX twisted-pair copper cable lines to two
(2) 100Base-FX fiber-optic cable lines. The
SISTF10xx-130-LR(T) is designed for harsh industrial
environments such as hazardous locations (Class 1 Division 2 / Zone 2), includes a
relay output warning alarm, and is designed to withstand a high degree of vibration
and shock. It is also available in models that operate in either standard or extended
temperature ranges.

2
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
NOTE: This device is intended to be grounded to a well-grounded
mounting surface such as a metal plate. Install the grounding wire prior
to connecting any other device.
Ground the SISTF10xx-130-LR(T)
Grounding the device helps limit the effects of noise due to electromagnetic
interference (EMI). The grounding screw is located on the top panel next to
the terminal block.
To ground the SISTF10xx-130-LR(T):
1. Connect one end of the grounding wire (not included) to the grounding
screw by looping one end of the grounding wire under the star washer.
2. Tighten the grounding screw with a phillips-head screwdriver.
3. Connect the other end of the grounding wire to earth ground.
g
rounding screw
terminal block
DIN-Rail
spring
mounting
plate
Step 1: Step 2:
Installation
DIN-Rail Mount
The SISTF10xx-130-LR(T) Ethernet switch includes an aluminum DIN-Rail
mounting plate attached to the device’s back panel. To mount the SISTF10xx-
130-LR(T) onto a DIN-Rail:
1. Insert the top of the DIN-Rail into the upper slot of the mounting plate.
The stiff metal spring should be positioned behind the DIN-Rail.
2. Push down and rotate the device to snap it into place on the DIN-Rail as
shown.
[email protected] -- Click the “Transition Now” link for a live Web chat. 3
Installation -- Continued
The SISTF10xx-130-LR(T) is a plug-and-play unmanaged Ethernet switch with
Redundant Ring technology for better network reliability and faster recovery
time. The recovery time is less that 300 ms compared to 3 to 5 minutes for
commercial switches. Also, when one segment of the network gets
disconnected, the Redundant Ring automatically re-establishes network
connectivity.
Master Device
The Redundant Ring technology identifies one switch as the Ring Master of
the network, and then automatically blocks packets from traveling through
any of the network’s redundant loops. To designate one of the SISTF10xx-
130-LR(T) devices to be the network’s Ring Master, set switch 6 on that device
to “ON”.
If two or more devices are set to be the Ring Master, those devices with their
switch 6 set to “ON” auto-negotiate to determine which one is the Ring
Master. Also, if none of the devices are set to be the Ring Master, the
Redundant Ring technology chooses the device that has the smallest MAC
address range to be the Ring Master.
The actual topology of the Redundant Ring (i.e., which segment is blocked) is
determined by the number of
devices that make up the ring:
If there is an odd number of devices
in the ring, the backup segment is
the segment directly opposite the
Ring Master:
If there is an even number of
devices in the ring, the backup
segment is one of the two segments
connected to the unit directly
opposite the Ring Master:
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
master switch
in the network
network's backup segment
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
network's backu
p
segments
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
TX
TX
PWR1
PWR2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
master switch
in the network

4
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation -- Continued
CAUTION: Disconnect the SISTF10xx-130-LR(T) from the DC power
source BEFORE installing and/or wiring the device.
Install the Fiber Cable
To build the Redundant Ring network, connect the SISTF10xx-130-LR(T)
devices using the two fiber ports labeled “4” and “5”. The fiber links can be
connected between two adjacent devices using any of the following
combinations:
A: Port 4 of one device connected to port 4 of the adjacent device.
B: Port 4 of one device connected to port 5 of the adjacent device.
C: Port 5 of one device connected to port 5 of the adjacent device.
When connecting the fiber links, make sure the transmit (TX) port on one
device is connected to the receive (RX) port on the adjacent device as shown:
TX
TX
PWR 1
PWR 2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
TX
TX
PWR 1
PWR 2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
TX
TX
PWR 1
PWR 2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
port 5
p
ort 5
p
ort 4 port 4
port 4
port 5
A
B
C
Connect the fiber
cable to the
SISTF10xx-130-LR(T)
as shown.
Connect the fiber
cable to the adjacent
SISTF10xx-130-LR(T)
as shown
RX
TX
RX
TX
NOTE: Calculate the maximum possible current in each power wire and
signal wire. Observe all electrical codes for maximum current allowed.
If the current goes above the maximum ratings, the wiring would
overheat, causing serious damage to the network equipment.
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the dip switches. Failure to observe this caution
could result in damage to, and failure of, the SISTF10xx-130-LR(T).
Set the Dip Switches
• The dip switches are located on the top panel of the device.
• Use a small flat blade screwdriver or a similar device to set the switches.
NOTE: To activate the updated switch setting, cycle the power to the
SISTF10xx-130-LR(T) by turning off the power, then turning it back on.
Switches 1 - 5: Port Alarm
The port alarm feature is used to determine faults at the copper or fiber ports.
• Switches 1, 2, and 3 correspond to copper ports 1, 2, and 3, respectively.
• Switches 4 and 5 correspond to fiber ports 4 and 5, respectively.
on: Enables the corresponding port alarm.
If the link for that port fails (or if a
power supply input fails), the internal
relay forms an open circuit and the
FAULT LED lights up.
off: Disables the corresponding port
alarm. The internal relay forms a
closed circuit and the FAULT LED
remains off.
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
PORT
ALARM
RING
MASTER
DIPON
1
P1
2
P2
3
P3
4
P4
5
P5
6
RM
RJ-45 port
on the other device
(PLC, work station, etc.)
RJ-45 ports on the
SISTF10xx-130-LR(T)
Installation -- Continued
Install the Copper Cable
The AutoCross feature allows either straight-through (MDI) or crossover (MDI-
X) copper cable to be used when connecting devices via the RJ-45 port.
1. Locate or build 10Base-T or 100Base-TX copper cables with male, RJ-45
connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the SISTF10xx-130-LR(T).
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (PLC, workstation, etc.).

V2-
V1-
V1+
V2+
PWR2
FAULT
PWR1
The screws to secure
the wires are located
on the side of the
terminal block.
fault contacts
6
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Install the Port Alarm Device
A user-supplied port alarm device can be connected to the SISTF10xx-130-LR
to alert the user whenever a power fault or a port fault occurs. At least one
port alarm switch or the Ring Master switch (see page 5) must be “ON” to
enable the port alarm feature.
The contacts for the fault alarm are on the 6-contact terminal block, located
on the top panel of the SISTF10xx-130-LR(T). To install a port alarm device:
1. Insert the two wires from the user-supplied port alarm device into the two
terminals marked “FAULT” on the 6-contact terminal block.
2. Secure the wire by tightening the corresponding screw on the side of the
terminal block.
Installation -- Continued
Switch 6: Ring Master
on: Enables the device to be the Ring Master in a Redundant Ring topology.
This setting also enables the Redundant Ring break alarm. If a link in the
Redundant Ring breaks (and if the SISTF10xx-130-LR(T) is the Ring
Master in the Redundant Ring topology), then the internal relay forms an
open circuit and the FAULT LED lights up.
off: Disables the device from being the Ring Master.
If none of the devices are set to be the Ring Master, the Redundant Ring
technology chooses the device that has the smallest MAC address range
to be the Ring Master. However, if the Redundant Ring is broken, the
internal relay remains closed and the FAULT LED remains off.
Internal Relay
The internal relay that activates the alarm feature is connected to the two
middle contacts on the 6-contact terminal block. A user-supplied fault alarm
device can be connected to these fault contacts. An example would be to
connect the fault circuit to a warning light located in the control room. The
light can be set up to turn on when a fault is detected (see below).
[email protected] -- Click the “Transition Now” link for a live Web chat. 7
Installation -- Continued
Power the SISTF10xx-130-LR(T)
This device is suitable for use in Class I, Division 2, Groups A, B, C and D or
non-hazardous locations only.
WARNING: EXPLOSION HAZARD - Do not disconnect equipment
unless power has been removed or the area is known to be non-
hazardous.
WARNING: EXPLOSION HAZARD - Substitution of components may
impair suitability for Class I, Division 2.
The SISTF10xx-130-LR(T) is designed for both a primary and a backup power
supply via the 6-contact terminal block, located on the top panel of the
device. Both power inputs can be connected simultaneously to live DC
power sources. If one power source fails, the other live source acts as a
backup, and automatically supplies the device with power.
CAUTION: Before connecting the SISTF10xx-130-LR(T) to the 12-48
VDC power source, ensure the power source voltage is stable.
To provide PRIMARY (PWR1) power to the SISTF10xx-130-LR(T):
1. Insert the positive (+) DC wire from the 12-48VDC power source into the
terminal marked “V1+”.
2. Insert the negative (-) DC wire into the terminal marked “V1-”.
3. Secure the wires by tightening the corresponding screws on the side of
the terminal block.
To provide BACKUP (PWR2) power to the SISTF10xx-130-LR(T):
1. Insert the positive (+) DC wire from the 12-48VDC power source into the
terminal marked “V2+”.
2. Insert the negative (-) DC wire into the terminal marked “V2-”.
3. Secure the wires by tightening the corresponding screws on the side of
the terminal block.
V2-
V1-
V1+
V2+
PWR2
FAULT
PWR1
V1, V2 INPUTS
12-48 VDC
The screws to secure
the wire are located
on the side of the
terminal block.
backup power
contacts
p
rimary power
contacts
6-contact terminal block

8
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Operation
Status LEDs
Use the status LEDs to monitor the SISTF10xx-130-LR(T) in the network.
The three LEDs near the top indicate the power and fault status:
PWR1 (amber) on = Primary power is connected to device.
PWR2 (amber) on = Backup power is connected to the device.
FAULT (red) on = If any of the five (5) port
alarm switches are “on“ and
the link on the corresponding
port is inactive (ex: switch 3
is “on” and port 3 is inactive);
or if there is a loss of primary
or backup power
The “100M” LEDs indicate the link status of the
corresponding fiber port (100Base-FX):
100M (green) on = Fiber link is active.
flashing = Data is being
transmitted over the fiber link.
The “RING MASTER” LED indicates whether or not
the SISTF10xx-130-LR(T) is the current Ring Master
of the Redundant Ring network:
RING (green) on = The device is the Ring
MASTER Master of the Redundant Ring
Network.
flashing = A link in the
Redundant Ring is broken.
The LEDs embedded in each of the RJ-45 ports
indicate the status of the corresponding copper link
(10/100Base-T/TX):
10M (green) on = Copper link is active at 10 Mb/s.
flashing = Data is being transmitted over the copper link
at 10 Mb/s.
100M (green) on = Copper link is active at 100 Mb/s.
flashing = Data is being transmitted over the copper link
at 100 Mb/s.
TX
TX
PWR 1
PWR 2
FAULT
Redundant Ring Industrial Switch
RX
RX
10/100BASE-TX
100BASE-FX
100M
100M
RING
MASTER
[email protected] -- Click the “Transition Now” link for a live Web chat. 9
AutoCross
The AutoCross feature allows either straight-through (MDI) or crossover (MDI-
X) cables to be used when connecting the SISTF10xx-130-LR(T) to devices
such as PLCs or workstations. AutoCross determines the characteristics of the
cable connection and automatically configures the unit to link up, regardless
of the cable configuration. (Requires no operator intervention.)
Operation -- Continued
Features
Auto-Negotiation
With the Auto-Negotiation feature, the SISTF10xx-130-LR(T) automatically
configures itself to achieve the best possible mode of operation over the
copper link. The device broadcasts its speed (10 Mb/s or 100 Mb/s) and
duplex capabilities (either full- or half-duplex) and negotiates the best mode of
operation between the two linked devices.
If the device is connected to a non-negotiating device over the copper link, it
will default to 10 Mb/s speed, half-duplex mode.
Plug-and-Play
The SISTF10xx-130-LR(T) models are plug-and-play devices, so that software
configuration is not required at installation or during maintenance.
Switching, Filtering, and Forwarding
Packets are either filtered or forwarded when they arrive at one of the
switched ports.
• Packets with source and destination addresses belonging to the same port
segment are filtered and constrained to one port (relieving the rest of the
network from the need to process them).
• Packets with a destination address to another port segment are forwarded
to the appropriate port, and are not sent to the other ports where it is not
needed.
• Packets that are used in maintaining the operation of the network (such as
the occasional multi-cast packet) are forwarded to all ports.
The Ethernet switch operates in the store-and-forward switching mode, which
eliminates bad packets and enables peak performance to be achieved when
there is heavy traffic on the network.
Switching and Address Learning
The Ethernet switch address table holds up to 1K node addresses, making it
suitable for use with large networks. The address tables are self-learning, so
that as nodes are added, removed, or moved from one segment to another, the
Ethernet switch automatically keeps up with new node locations. An address-
aging algorithm deletes the least-used addresses in favor of newer, more
frequently used addresses. To reset the address buffer, power down the unit
and then power it back up.

10
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Cable Specifications -- Continued
Copper Cable
Category 5: (minimum requirement)
Gauge: 24 to 22 AWG
Attenuation: 22.0 dB /100m @ 100 MHz
Maximum Cable Distance: 100 meters
• Straight-through OR crossover cable may be used.
• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .
• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
Crossover Cable
1
2
3
6
Straight-Through Cable
Twisted Pair #1
Twisted Pair #1
Twisted Pair #2
Twisted Pair #2
1
2
3
6
1
2
3
6
1
2
3
6
Please note the following when wiring the network:
• Signal lines must not be directly connected to outdoor wiring.
• Use separate paths to route the power wiring and the signal wiring. If
power wiring and signal wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
• Do not run signal wiring and power wiring in the same wire conduit. To
avoid interference, wires with different signal characteristics should also
be routed separately.
• Use the type of signal transmitted through a wire to determine which
wires should be kept separate. The rule of thumb is that wiring with
similar electrical characteristics can be bundled together.
• Keep input wiring and output wiring separate.
• Where necessary, label the wiring to all devices in the network.
NOTE: This device has been evaluated as EEx nC IIC T4 equipment
under DEMKO Certificate No. 03 ATEX 0324537U. Each module is
suitable for use in Zone 2 Explosive Atmospheres. The device must be
installed in a minimum IP 54 enclosure as defined in IEC 60529 and EN
60529.
NOTE: This unit is a building-in type. The installation into a certain end
equipment shall comply with fire enclosure request of IEC
60950/EN60950 or similar sentence.
11
[email protected] -- Click the “Transition Now” link for a live Web chat.
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber Cable
Bit Error Rate: <10-9
Single mode fiber (recommended): 9 µm
Multimode fiber (recommended): 62.5/125 µm
Multimode fiber (optional): 100/140, 85/140, 50/125 µm
Standard Models
SISTF1011-130-LR 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1012-130-LR 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
SISTF1013-130-LR 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1014-130-LR 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
Extended Temperature Models
SISTF1011-130-LRT 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1012-130-LRT 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
SISTF1013-130-LRT 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1014-130-LRT 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
NOTE: The fiber optic transmitters on this device meet Class I Laser
safety requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.

12
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model SISTF10xx-130-LR(T) or equivalent
Standards: IEEE 802.3™, 802.3u™; 802.3x™
Data Rate: 10 Mb/s, 100 Mb/s (copper); 100 Mb/s (fiber)
Processing Type: Store and Forward
w/ IEEE802.3x™ full-duplex, non-blocking flow control
Dimensions: 1.8" x 5.3" x 4.1" (46 mm x 135 mm x 105 mm)
Weight: 1.4 lb. (0.65 kg) (approximate)
Input Power: 12-48VDC, 0.2-0.7A, 24W (minimum), (redundant inputs)
with overload and reverse polarity protection
Address Table Size: 1,000 Unicast Mac addresses
Alarm Relay: 1 Amp @ 24 VDC
Mechanical: Ingress Protection: IP30
Environment: Tmra* (standard temp): 0 to 60°C (32 to 140°F)
Tmra* (extended temp): -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Humidity: 5 to 95%, non condensing
Warranty: Lifetime
*Manufacturer’s rated ambient temperature.
The information contained in this user’s guide is subject to change. For the most
up-to-date information see the user’s guide on line at: www.transition.com.
This device is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not
stare into beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of
procedures other than those specified herein may result in hazardous
radiation exposure
CAUTION: This device is intended to be supplied by a listed power unit
marked LPS or Limited Power Source, provided with a connector for field
wiring terminal, and output rated 12-48VDC, 0.2-0.7 A, 24 W minimum.
CAUTION: This device is designed for operation with a safety extra-low
voltage (SELV) in compliance with IEC950 / EN60950 / VDE0805 and in
compliance with the low voltage directive 73/23/EEC and 93/68/EEC.
[email protected] -- Click the “Transition Now” link for a live Web chat. 13
Test Description Test Levels
IEC 60068-2-6 Vibration 10 - 500 - 10 Hz, 0.5 oct./min, 4g, X, Y, Z (3 axes)
IEC 60068-2-27 Shock 50 g, 11 ms, +/-X, +/-Y, +/- Z (6 direction)
IEC 60068-2-32 Free fall 75 cm, 1 corner, 3 edges, 6 faces (total 10 drops)
Environmental Type Tests
Test Description Test Levels Severity
IEC61000-4-2 ESD Air discharge +/- 8 KV 3
Contact discharge +/- 6 KV 3
ESD contact discharge +/- 6 KV 3
IEC61000-4-3 Radiated RFI Housing 10V/m, 80 MHz - 1 GHz
AM 1 KHz, 80% mod
10 V/m, 0.9 - 1.8 GHz
FM 200 Hz 50% square
3
IEC61000-4-4 Burst
(Fast Transient)
Power supply lines +/- 2 KV 3
Communication lines +/- 1 KV 3
Relay +/- 1 KV 3
IEC61000-4-5 Surge Power supply lines +/- 2 KV, 12 Ω, CM
+/- 1 KV, 2 Ω, DM
3
Relay +/- 2 KV, 12 Ω, CM
+/- 1 KV, 2 Ω, DM
3
IEC61000-4-6 Induced
(Conducted RFI)
Power supply lines 10 Vrms, 150-80 MHz
AM 1 KHz, 80% mod
3
Communication lines 10 Vrms, 150-80 MHz
AM 1 KHz, 80% mod
3
Relay 10 Vrms, 150-80 MHz
AM 1 KHz, 80% mod
3
Technical Specifications -- Continued
EMS Type Tests

14
SISTF10xx-130-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Troubleshooting
If the device fails, isolate and correct the fault by determining the answers to the
following questions and then taking the indicated action:
1. Is the PWR1 LED illuminated?
NO
• Ensure the power source is the proper voltage (12 - 48 VDC).
• Ensure the (+) and (-) wires from the power source are inserted
properly in the terminal block contacts labeled “PWR1”.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 2.
2. Is the PWR2 LED illuminated?
NO
• Ensure the power source is the proper voltage (12 - 48 VDC).
• Ensure the (+) and (-) wires from the power source are inserted
properly in the terminal block contacts labeled “PWR2”.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 3.
3. Is the FAULT LED illuminated?
YES
• If one or more port alarm switches (1 - 5) is ON,the device lost the
corresponding fiber or copper link; or primary or backup power.
• Ensure the problem copper or fiber link is properly connected.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Proceed to step 4.
4. Is the Ring Master LED flashing?
YES
• A link in the Redundant Ring is broken. Inspect the fiber links in the
ring for proper connection.
• Verify that the TX and RX cables on one device are connected to the
RX and TX ports, respectively, on the adjacent device.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Proceed to step 5.
5. Are either 100M LEDs (near the fiber links) illuminated?
NO
• Check the corresponding fiber cables for proper connection.
• Verify that the TX and RX cables on the device are connected to the
RX and TX ports, respectively, on the other device.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 6.
Troubleshooting -- Continued
6. Are either 100M LEDs (near the fiber links) flashing?
NO
• If there is activity on the corresponding fiber port, disconnect and
reconnect the fiber cable to restart the initialization process.
• If there is no activity on the corresponding fiber port, contact Tech
Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 7.
7. Are any of the 10M LEDs (on the RJ-45 port) illuminated?
YES
• The device has selected 10 Mb/s for the twisted-pair link.
• If the speed is not correct, disconnect and reconnect the twisted-pair
cable to restart the initialization process.
• Proceed to step 8.
NO
• Proceed to step 8.
8. Are any of the 100M LEDs (on the RJ-45 port) illuminated?
YES
• The device has selected 100 Mb/s for the twisted-pair link.
• If the speed is not correct, disconnect and reconnect the twisted-pair
cable to restart the initialization process.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Check the twisted-pair cables for proper connection.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
[email protected] -- Click the “Transition Now” link for a live Web chat. 15
Declaration of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344, USA
Model: SISTF10xx-130-LR(T) Series Redundant Ring Industrial Switches
Part Number(s): SISTF1011-130-LR, SISTF1012-130-LR, SISTF1013-130-LR,
SISTF1014-130-LR, SISTF1011-130-LRT, SISTF1012-130-LRT,
SISTF1013-130-LRT, SISTF1014-130-LRT
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the
SISTF10xx-130-LR(T) to which this declaration refers
is in conformity with the following standards.
EN 55022:1998 Class A; FCC Part 15 Subpart B; 21CFR subpart J;
UL 60950; UL 508; CSA C22.2 no 60950; EN 60950;
UL/cUL Class 1, Div 2, Groups A, B, C, D; ATEX Class 1, Zone 2, EExnC IIC;
EN61000-4-2, -4-3, -4-4, -4-5, -4-6; IEC 60068-2-6, -2-27, -2-32
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
_December 3, 2004_____
Stephen Anderson, Vice-President of Engineering Date
NOTE: The following part numbers are UL listed: SISTF1013-130-LR, SISTF1013-130-
LRT, SISTF1014-130-LR, SISTF1014-130-LRT

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network. Der Anschluss dieses Gerätes an ein
öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die
jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendein-
richtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions © 2004 Transition Networks. All rights reserved. No part of this
work may be reproduced or used in any form or means (graphic, electronic, mechanical)
without written permission from Transition Networks. Printed in the U.S.A.
33310.A
Compliance Information
UL Listed; C-UL Listed (Canada)
CISPR22/EN55022 Class A CE Mark
FCC Regulations This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user's own expense.
Canadian Regulations This digital apparatus does not exceed the Class A limits for radio
noise for digital apparatus set out on the radio interference regulations of the Canadian
Department of Communications. Le présent appareil numérique n'émet pas de bruits
radioélectriques dépassant les limites applicables aux appareils numériques de la Class A
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
European Regulations
Warning: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
Achtung ! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können
bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für
Gegenmaßnahmen verantwortlich.
Attention ! Ceci est un produit de Classe A. Dans un environment domestique, ce produit
risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de
prende les measures spécifiques appropriées.
Contact Transition Networks
Technical support is available 24 hours a day.
US and Canada: 1-800-260-1312 International: 00-1-952-941-7600
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
Send an e-mail anytime to our technical support staff at: [email protected]
Transition Networks, 6475 City West Pkwy, Minneapolis, MN 55344, USA
telephone: [phone], toll free: 800-526-9267, fax: [phone]
NOTE: The following part numbers are UL listed: SISTF1013-130-LR, SISTF1013-130-LRT,
SISTF1014-130-LR, SISTF1014-130-LRT.