Transition Networks SM8TAT2SA Instruction Manual

33718 Rev. A https://www.transition.com Page 1of 255
SM8TAT2SA, SM16TAT2SA, and
SM24TAT2SA
Smart Managed Switches, 8-/16-/24-Port
Gigabit PoE+, 2-Port 100/1000 SFP
CLI Reference
33718 Rev. B

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 2of 255
Trademarks
All trademarks and registered trademarks are the property of their respective owners.
Copyright Notice/Restrictions
Copyright © 2017 Transition Networks. All rights reserved. No part of this work may be reproduced or
used in any form or by any means (graphic, electronic or mechanical) without written permission from
Transition Networks. Printed in the U.S.A.
SMxTAT2SA Smart Managed Switches CLI Reference, 33718 Rev. B
Contact Information
Transition Networks
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: [phone] | toll free: 1.800.526.9267 | fax: [phone]
[email protected]om |[e-mail] |customerse[email protected]
Revision History
Rev
Date
Description
A
3/8/17
Preliminary release for SMxTAT2SA at v1.00.
B
12/20/17
Update for FW v1.01.1209 which removes the show dms command.

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 3of 255
CONTENTS
CONTENTS ..........................................................................................................................................................3
1 CLI Management .......................................................................................................................................4
1-1 LOGIN ........................................................................................................................................................ 5
1-2 OVERVIEW OF CLI COMMANDS...................................................................................................................... 5
2 CLEAR Commands................................................................................................................................... 10
3 CONFIGURE Commands ......................................................................................................................... 13
3-2 NO .......................................................................................................................................................... 80
3-3 QOS....................................................................................................................................................... 117
3-4 SNMP-SERVER ......................................................................................................................................... 120
3-5 SPANNING-TREE ....................................................................................................................................... 126
4 COPY Commands ................................................................................................................................... 131
5 DELETE Commands ................................................................................................................................ 133
6 DIR Commands ...................................................................................................................................... 134
7 DO Commands....................................................................................................................................... 135
8 DOT1x Commands ................................................................................................................................. 136
9 FIRMWARE Commands ......................................................................................................................... 139
10 NO Commands..................................................................................................................................... 140
11 PING Commands.................................................................................................................................. 143
12 RELOAD Commands............................................................................................................................. 145
13 SHOW Commands ............................................................................................................................... 146
14 TERMINAL Commands......................................................................................................................... 210
15 TRACEROUTE Commands .................................................................................................................... 211
16 CLI Command Summary ...................................................................................................................... 213

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 4of 255
1 CLI Management
This manual documents CLI (Command Line Interface) commands for three similar models: SM8TAT2SA,
SM16TAT2SA, and SM24TAT2SA. The models differ mainly in port count. Model differences are noted where
applicable throughout this manual. A brief description of a typical connection is provided below:
□An-RJ-45 cable is used for connecting a terminal or terminal emulator to an RJ-45 port on the
SMxTAT2SA front panel to access the CLI.
□Attach an RJ-45 port on the switch’s front panel to the cable for CLI configuration.
□Attach the other end of the DB-9 cable to a PC running Tera Term or similar utility.
□At the “Tera Term New connection” menu, configure the parameters: Host: 192.168.1.77; History:
checked; Service: SSH; TCP port # 22; SSH version: SSG2; Protocol: UNSPEC.

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 5of 255
1-1 Login
The command-line interface (CLI) is a text-based interface that you can access the CLI through either a direct
serial connection to the device or a Telnet session. The default username and password to login into the
switch are:
Username: admin
Password: admin
After you login successfully, the prompt displays as “<sys_name>#“ . This means you are an administrator
and have the highest privilege for setting the switch. If logged in as other than the administrator, the prompt
displays as “<sys_name>>”, which means you have guest privileges and are only allowed for setting the
system under the administrator. Each CLI command has its privilege level pre-assigned. See below.
Username: admin <tab>
Password: admin <Enter>
SM16TAT2SA
1-2 Overview of CLI Commands
The CLI is divided into several modes. If you have enough privilege to run a particular command, you may run
the command in the correct mode. To see the commands of the mode, enter a “?” (question mark) after the
system prompt, then all commands will be listed in the screen. The command modes are listed below:
Command Modes
Mode
Prompt
Command Function in this Mode
exec
<sys_name>#
Display current configuration, diagnostics, and
maintenance
config
<sys_name>(config)#
Configure features other than those below
Config-if
<sys_name>(config-interface)#
Configure ports
Config-if-vlan
<sys_name>(config-if-vlan)#
Configure static vlan
Config-line
<sys_name>(config-line)#
Line Configuration
Config-ipmc-profile
<sys_name>(config-impc-profile)#
IPMC Profile
Config-snmp-host
<sys_name>(config-snmp-host)#
SNMP Server Host
Config-stp-aggr
<sys_name>(config-stp-aggr)#
STP Aggregation
Config-dhcp-pool
<sys_name>(config-dhcp-pool)#
DHCP Pool Configuration
Config-rfc2544-profile
<sys_name>(config-rfc2544-profile)#
RFC2544 Profile

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 6of 255
Commands reside in the corresponding modes could run only in that mode. If you want to run a particular
command, you just change to the appropriate mode. The command modes are organized as a tree, starting in
exec mode. The following table explains how to change from one mode to another.
Change Between Command Modes
Mode
Enter Mode
Leave Mode
exec
--
--
config
Configure terminal
exit
config-interface
Interface <port-type> <port-type-list>
exit
config-vlan
Interface vlan <vlan_list>
exit
Idle timeout Message
Warning: Idle timeout. The session will be closed.
After the session times out, you must log back in again. Press the Enter key to display the Username prompt.
SM16TAT2SA#
Warning: Idle timeout. The session will be closed.
<Enter>
Username: admin
Password:
SM16TAT2SA#

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 7of 255
1-3 Global CLI Commands
To see the commands of the current mode, type a question mark (?) after the prompt to list all available
commands for that mode.
SM16TAT2SA# ?
! Comments
clear Reset functions
configure Enter configuration mode
copy Copy from source to destination
delete Delete one file in flash file system
diagnostics diagnostics
dir Directory of all files in flash file system
exit Exit from the CLI
find-switch Turn on and off all LED light 3 times in 15 seconds
firmware firmware
logout Exit from EXEC mode
more Display file
ping Send ICMP echo messages
reload Reload system
show Show running system information
ssl Setup SSL certificate
terminal Set terminal line parameters
traceroute Trace the route to HOST
SM16TAT2SA#

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 8of 255
ExitExit from Config mode to EXEC mode.
Syntax: exit
Parameter: None.
Example:
SM16TAT2SA(config)# exit
SM16TAT2SA#
? (Help)
Help may be requested at any point in a command by entering a question mark '?'. If nothing matches,
the help list will be empty and you must back up until entering a '?' shows the available options.
Two styles of help are provided:
1. Full help is available when you are ready to enter a command argument (e.g. 'show ?') and describes
each possible argument.
2. Partial help is provided when an abbreviated argument is entered and you want to know what
arguments match the entry (e.g. show pr?).
Syntax: ?
Parameter: None.
Example:
SM16TAT2SA# ?
! Comments
clear Reset functions
configure Enter configuration mode
copy Copy from source to destination
delete Delete one file in flash file system
diagnostics diagnostics
dir Directory of all files in flash file system
exit Exit from the CLI
find-switch Turn on and off all LED light 3 times in 15 seconds
firmware firmware
logout Exit from EXEC mode
more Display file
ping Send ICMP echo messages
reload Reload system
show Show running system information
terminal Set terminal line parameters
traceroute Trace the route to HOST
SM16TAT2SA#

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 9of 255
logout
Exit from EXEC mode. You must log back in.
Syntax:
logout
Parameter:
none
Example:
SM16TAT2SA# logout
end Go back to EXEC mode.
Syntax:
end
Example:
SM16TAT2SA# configure terminal
SM16TAT2SA(config)# end
SM16TAT2SA#

Transition Networks SMxTAT2SA CLI Reference
33718 Rev. B https://www.transition.com Page 10 of 255
2 CLEAR Commands
Table : Clear Commands
Command Function
access-list Access list
ip Clear DHCP Relay statistics
lldp Clear LLDP statistics for one or more given interface
logging Syslog
mac MAC Address Table
spanning-tree Execute protocol migration check on interfaces
statistics Clear statistics for one or more given interface
lldp
Clears LLDP statistics.
Syntax
Clear lldp statistics
Parameters
global Clear global counters
interface Interface
EXAMPLE
SM16TAT2SA# clear lldp?
lldp Clear LLDP statistics for one or more given interface
SM16TAT2SA# clear lldp ?
statistics Clear LLDP statistics
SM16TAT2SA# clear lldp statistics ?
global Clear global counters
interface Interface
SM16TAT2SA# clear lldp statistics global ?
<cr>
SM16TAT2SA# clear lldp statistics interface ?
GigabitEthernet GigabitEthernet
* All ports
SM16TAT2SA# clear lldp statistics interface GigabitEthernet ?
<port_list> Port List S/X-Y,Z (1/1-18)
SM16TAT2SA# clear lldp statistics interface GigabitEthernet 1/3-7