Transition Networks E-TBT-HB-0402 User manual

For assistance in installing, using, or
maintaining the TRANSITION Networks
Model 0402 Ethernet Pocket Hub,
contact TRANSITION Networks
Technical Support at:
[phone]
or contact your local distributor.
7349.E
™™
Pocket HubEthernet
(E-TBT-HB-0402)
Model 0402
MODEL 0402 ETHERNET POCKET HUB
SPECIFICATIONS
Standards
IEEE 802.2, 802.3
Physical
Dimensions
4.80" X 2.77" X 0.95" (122mm x 70mm x 24mm)
Input Power
Power Supply Adapter
AC Input:
TN PN Requirement Location
3518 120 volts, 60 hertz, 28 watts USA/Canada/Mexico
3516 230 volts, 50 hertz, 28 watts Europe
3514 100 volts, 50-60 hertz, 28 watts Japan
3517 240 volts, 50 hertz, 28 watts United Kingdom
3515 240 volts, 50 hertz, 28 watts Australia
DC Output:
9 volts at 500 mA maximum
MTBF
43,000 hours
Environment
Temperature: 0-50°C (32° to 122° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty
5 years
Model 0402
17

Model 0402 Ethernet™ Pocket Hub™ 16
CAUTION: RJ connectors are NOT INTENDED FOR
CONNECTION TO THE PUBLIC TELEPHONE
NETWORK. Failure to observe this caution could result
in damage to the public telephone network.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class
A digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for
digital apparatus set out on the radio interference regulations of the Canadian
Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Copyright Restrictions
© 1995, 1996 TRANSITION Networks Inc.
All rights reserved. No part of this work may be reproduced or used in any
form or by any means – graphic, electronic, or mechanical – without written
permission from TRANSITION Networks Inc.
Trademark Notice
All registered trademarks and trademarks are the property of their respective
owners.
Der Anschluss dieses Gerätes an ein öffentlickes
Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die
jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie
91/263/EWG zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
10Base2 Cable Specifications
The physical characteristics of the 10Base2 cable must meet or exceed IEEE 802.3
10Base2 specifications.
Cable Characteristics:
Cable type: Stranded Coaxial RG58 (ThinNet)
Impedance: 50 Ω@ 10 MHz
Mutual Capacitance: 24 pF/ft ±20% @ 10 MHz
Maximum Cable Length:185 meters (610 feet)
Maximum number network connections:30
Minimum distance between connections: 0.5 meters (1.6 feet)
Terminate 10Base2 cable at one end using a 50 ohm terminator and at the
other end using a 50 ohm terminator grounded to earth ground.
10BaseT Cable and Connector Specifications
The physical characteristics of the 10BaseT cable must meet or exceed IEEE 802.3
10BaseT specifications.
10BaseT Cable Characteristics:
Category 3 wire or better is required; category 5 wire is recommended. Either
shielded twisted pair (STP) or unshielded twisted pair (UTP) can be used. DO
NOT USE FLAT OR SILVER SATIN WIRE.
Category 3:
Gauge 24 to 22 AWG
Attenuation 28 dB/1000’ @ 10 MHz
Differential Characteristic Impedance 100 Ω±10% @ 10 MHz
Category 5:
Gauge 24 to 22 AWG
Attenuation 20 dB/1000’ @ 10 MHz
Differential Characteristic Impedance 100 Ω±10% @ 10 MHz
Maximum Cable Length: 100 meters (330 feet)
10BaseT Connector Characteristics:
The two active pairs in a 10BaseT network are pins 1 & 2 and pins 3 & 6. Use
only dedicated wire pairs (such as blue/white & white/blue, orange/white &
white/orange) for the active pins. 10BaseT cable for unlike devices (such as
hub to terminal device) must be configured as straight through; 10BaseT cable
for like devices (such as hub to hub or terminal device to terminal device) must
be configured as crossover.
Twisted
Pair #1
Twisted
Pair #2
Crossover Cable
Connectors for like devices
Twisted
Pair #1
Twisted
Pair #2
Straight Through Cable
Connectors for unlike devices

Table of Contents
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
The 0402 Ethernet Pocket Hub . . . . . . . . . . . . . . . . . . . . . . .1
0403 Pocket Hub Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Networking the 0402 Pocket Hub . . . . . . . . . . . . . . . . . . . . . . .2
0402 Ethernet Pocket Hub Connectors . . . . . . . . . . . . . . . . .3
RJ-45 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Power Supply Adapter Connector . . . . . . . . . . . . . . . . . . . . . . .3
0402 Ethernet Pocket Hub Status Indicators . . . . . . . . . . . . . .4
Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Link/Transmit LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 SITE CONSIDERATIONS. . . . . . . . . . . . . . . . . . . . 5
Ensuring Compliance with Ethernet 802.3 . . . . . . . . . . . . . . .6
Segment Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Ensuring Correct 10BaseT Configuration . . . . . . . . . . . . . . . .7
Straight Through/Crossover Cable Orientation . . . . . . . . . . . . . .7
Straight Through/Crossover Pin Specifications . . . . . . . . . . . . . .8
3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unpacking 0402 Pocket Hub . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting 10BaseT Cable . . . . . . . . . . . . . . . . . . . . . . . . .10
Connecting Power to 0402 Pocket Hub . . . . . . . . . . . . . . . .10
4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Monitoring Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Monitoring Link/Transmit LEDs . . . . . . . . . . . . . . . . . . . . . .11
5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fault Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Technical Support Contact . . . . . . . . . . . . . . . . . . . . . . . . .12
WARRANTY STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CABLE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
0402 ETHERNET POCKET HUB SPECIFICATIONS . . . . . . 17
Model 0402 i
15 Ethernet™ Pocket Hub™
ETHERNET CABLE SPECIFICATIONS
AUI Cable and Connector Specifications
The cable is a special 4-pair individually shielded with an overall braided
shield.
Maximum AUI Cable Length: 50 meters (165 feet)
AUI Connector Characteristics:
AUI Port: Male DB-15 with locking posts.
AUI Connection: Cable shell must be grounded.
Connector Legend: 1 Logic Ref. 6 Power Return 11 Logic Ref
2 Collision+ 7 N/C 12 Receive
3 Transmit+ 8 Logic Ref. 13 Power
4 Logic Ref. 9 Collision-- 14 Logic Ref.
5 Receive+ 10Transmit- 15 N/C
10BaseFL Cable and Connector Specifications
The physical characteristics of the 10BaseFL cable must meet or exceed IEEE
802.3 10BaseFL specifications.
10BaseFL Cable Characteristics:
Fiber Optic Cable Recommended: 62.5/125 µm multimode fiber
Optional: 100/140 µm multimode fiber
85/125 µm multimode fiber
50/125 µm multimode fiber
Fiber Optic Transmitter Power: Average power: -15.0 dBm
Peak power:-12.0 dBm ±1dBm
Fiber Optic Receiver Sensitivity: Average sensitivity: -27.4 dBm
Bit error rate: ≤10-10
Maximum Cable Length: 2000 meters (6500 feet)
10BaseFL Connector Characteristics:
ST type connectors (SMA type available upon request)
10Base5 Cable and Connector Specifications
The physical characteristics of the 10Base5 cable must meet or exceed IEEE 802.3
10Base5 specifications.
10Base5 Cable Characteristics:
Cable type: RG8 Solid Coaxial (ThickNet)
Impedance: 50 Ω@ 10 MHz
Capacitance: 26pF/ft
Maximum Cable Length: 500 meters (1650 feet)
Maximum number network connections: 100
Minimum distance between connections: 2.5 meters (8.2 feet)
Terminate 10Base5 cable at one end using a 50 ohm terminator and at the
other end using a 50 ohm terminator grounded to earth ground.
Maximum number of terminal devices on Ethernet network: 1024

Model 0402 14
1Ethernet™ Pocket Hub™
1. INTRODUCTION
This guide is intended for the system or network administrator
responsible for installing and monitoring a TRANSITION Networks
0402 Ethernet Pocket Hub. A working knowledge of local area
network (LAN) operations, including familiarity with
communications protocols used on interconnected LANs, is
assumed.
The 0402 Ethernet Pocket Hub
The Model 0402 10BaseT 4-Port Ethernet Hub (E-TBT-HB-0402), is
a low cost Ethernet repeater. Designed to meet IEEE 802.3 10BaseT
standards, the 0402 Pocket Hub is a fully functional repeater in a
compact (4.80" X 2.77" X 0.95”) case.
0402 Ethernet Pocket Hub Features
•automatic link partitioning (jabber function isolates network
failures)
•preamble regeneration
•automatic polarity detection and correction
Ethernet™
Pocket Hub™
4 3 2 1
Power
1
2
3
4
E-TBT-0402
Link/Transmit
networks
TRANSITION
Mpls, MN 55344
The sole purpose of this remedy shall be provided the customer with the replacement or
repair of non-conforming goods in the manner described in this Warranty statement. This
exclusive remedy shall not be deemed to have failed of its essential purpose so long as TN is
willing and able to repair or replace the defective item(s) or refund the purchase price.
TN reserves the right to inspect products claimed to be defective under warranty either at the
customer’s location or at TN’s plant. TN assumes no liability for liability charges incidental
to the adjustment, service, repairing, removal or replacement of the product, or other costs,
or the expense of repairs made outside of its factory, except when made with TN’s prior
written consent. Additionally, Transition Networks reserves the right to charge for all testing
and shipping incurred, if after testing, a return is classified as “No Problem Found”.
TN’s total liability in connection with the products and their installation to all persons and
from all causes in the aggregate, whether in contract, tort, or strict liability, shall not exceed
the amount paid to TN for the product directly related to the alleged damage. However, in
no event shall TN have any liability to a customer or any third party for products
manufactures according to the customer’s specifications.
C. Return Procedure
The customer must follow this procedure for the return of defective items:
1. Locate the serial number(s) of the item(s) to be returned.
2. Determine the date the item(s) was received.
3. Contact Transition Networks Technical Support to determine if the problem can be
corrected on site.
If not, and the product is covered by warranty, then:
•Call the distributor directly or contact TN.
•Request a Return Material Authorization (RMA).
•Ship the item, prepaid in original packaging to Transition Networks at the above
address.
•Include the RMA number on the outside of the carton and/or on the Packing List.
•Include a copy of the RMA form.
•Include a copy of the original invoice or packing list (if possible) to expedite
processing.
•The item(s) may be shipped by the customer or the distributor.
•Transition Networks will repair or replace the unit, at TN’s discretion, and cover the
cost of the return freight to the distributor or to the customer, whichever requested
the RMA number.
If the item(s) was received more than five years ago, or if the item(s) is no longer covered by
warranty for other reasons, then:
•Call the distributor or contact TN.
•Request a Material Repair Authorization number (MRA).
•Ship the item(s), prepaid, in the original packaging to Transition Networks at the
above address.
•Include the MRA number on the outside of the carton add/or on the Packing List.
•Include a copy of the MRA form.
•Include a copy of the original invoice or packing list (if possible) to expedite processing.
•Only the customer (end-user) may send the items(s) to TN.
•TN will contact the customer after the item(s) have been received, inspected, and a
cost estimate of the repair determined.
•The repair charges may be billed, with customer’s approval, though the distributor, or
on a prepaid or C.O.D. basis directly to the customer. The charges will include the
cost of shipping.
The return authorization numbers are valid only for 90 days from the date issued.

Model 0402 2
13 Ethernet™ Pocket Hub™
Networking the 0402 Ethernet Pocket Hub
The 0402 Pocket Hub can function as the network backbone in both
simple and complex networks.
When centrally located in a small installation, the 0402 Pocket Hub
alone provides a simple, economical network solution.
When linked to other 0402 Pocket Hubs or to other 802.3 compliant
Ethernet repeaters, the Pocket Hubs function in complex Ethernet
networks.
Ethernet™ Pocket Hub™
networks
TRANSITION
Mpls,MN 55344
Ethernet™ Pocket Hub™
Ethernet™ Pocket Hub™
Ethernet™ Pocket Hub™
Ethernet™ Pocket Hub™
networks
TRANSITION
Mpls,MN 55344
networks
TRANSITION
Mpls,MN 55344
networks
TRANSITION
Mpls,MN 55344
networks
TRANSITION
Mpls,MN 55344
Warranty Statement
A. Five Year Warranty
Transition Networks, Inc. (TN) warrants, for a period of five years, that TN products (with
the exception of power supplies and fans that TN warrants for two years) will be free from
defects in materials and workmanship, and will be in conformity with TN’s specifications.
TN’s warranty on products manufactured by or assembled for TN in accordance with a
customer’s specifications, is a five-year warranty that the goods conform to such
specifications.
The warranty is invalidated if the goods have been subject to alterations, misuse, accident,
Acts of God (e.g., damage by floods, lightning strikes, Etc.), tampering, improper
maintenance, improper installation, or abuse. If the user is unsure about the proper means
of installing or using the equipment, contact TN’s free Technical Support or Network
Design Services, which can be reached by:
Telephone 1.800.LAN.WANS or 612.941.7600
Fax [phone]
E-mail [email protected]
Internet http://www.transition.com
THE ABOVE WARRANTY IS EXCLUSIVE AND EXTENDS ONLY TO PRODUCTS
ASSEMBLED BY TRANSITION NETWORKS, INC. TO THE EXTENT PERMITTED BY LAW,
TN DOES NOT MAKE AND DISCLAIMS ALL OTHER WARRANTIES, EXCEPT TITLE,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF
DESCRIPTION, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-
INFRINGEMENT, AND ANY WARRANTY BASED UPON PRIOR WRITTEN OR ORAL
REPRESENTATIONS REGARDING SUCH PRODUCTS MADE BY TN, ITS EMPLOYEES,
AGENTS, OR REPRESENTATIVES.
B. Limitations and Exclusions
If the customer believes any goods sold by TN are defective and within the warranty period,
the following general procedure will be followed:
1. Locate the serial number and delivery date of the item(s).
2. Notify TN within the warranty period.
3. TN will promptly issue a return authorization form for the goods.
4. Upon receiving the form, the customer will promptly return the item(s) at customers
own expense, shipped prepaid, to the distributor from which it was purchased, or
directly to TN.
TN will only accept goods for return if the following conditions have been met:
1. A return form is obtained from TN.
2. The freight charges have been prepaid by the customer.
3. Goods are re-packed in their original packaging.
If under warranty TN shall, at its option, (1) repair the goods free of charge (2) replace the
goods free of charge, or (3) accept the return of the item(s) and credit the current price to
the reseller (within 90 days of purchase), or (4) if the goods are not under warranty, will
repair the item(s) at a minimum charge of USD $200 (two hundred U.S. dollars) per item.
THIS IS THE EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. IN NO EVENT
SHALL TRANSITION NETWORKS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF ANY
CONDITION OF SALE, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY,
CONTRACT, OR OTHERWISE AND IRRESPECTIVE OF WHETHER TN IS INFORMED BY
CUSTOMER OF THE POSSIBILITY OF SUCH DAMAGES IN ADVANCE OF THIS SALE.

Model 0402 12
3Ethernet™ Pocket Hub™
5. MAINTENANCE
WARNING: DO NOT, UNDER ANY CIRCUMSTANCES,
open and attempt to repair the 0402 Pocket Hub or power
supply adapter unit. Failure to observe this warning could
result in personal injury or death from electrical shock.
NOTE: Failure to observe the above warning will immediately void
the warranty.
Fault Isolation
If two network devices fail to communicate through the 0402
Pocket Hub, consider the following:
•Are the LEDs described in the previous section functioning
properly?
•Do network devices have Link Integrity enabled?
•Do network devices communicate when the 0402 Pocket
Hub is not installed between them?
•Is flat or “silver satin”wire used in site internal wiring?
•Are internal wiring patch cords, punch down blocks, and
wall jacks properly pinned or configured?
•Is the AUI cable unbroken and properly connected?
•Are network interface cards properly configured?
Technical Support Contact
For assistance in fault isolation and in maintaining the 0402 Pocket
Hub, contact:
Technical Support [phone]
or your local distributor.
0402 Ethernet Pocket Hub Connectors and
Status LEDs
RJ-45 Connectors
Four (4) 10BaseT RJ-45 jack
connectors are located at one
end of the 0402 Pocket Hub.
The RJ-45 jacks support
connection to shielded or
unshielded 100 ohm twisted
pair 10BaseT cable.
Power Supply Adapter Connectors
An external power supply
adapter connector is located
at the other end of the 0402
Pocket Hub. The power
supply adapter connector
supplies external power.
Status LEDs
Power and Link/Transmit
status LEDs are located at
the side of the 0402 Pocket
Hub. The Power LED
indicates connection to
power. The Link/ Transmit
LEDs track the four 0402
Pocket Hub connections to
10BaseT.
RJ-45 Connectors
Power Supply Adapter
Connector
Status LEDs

Model 0402 4
11 Ethernet™ Pocket Hub™
4. OPERATION
The 0402 Pocket Hub normally requires no intervention beyond
occasionally monitoring the Power and Link/Transmit LEDs.
Monitoring Power LED
The green Power LED is illuminated when the Pocket Hub is
connected to power.
Monitoring Link/Transmit LEDs
Each of the green Link/Transmit LEDs , associated with one of the
eight RJ-45 ports:
•is illuminated when a device is connected to the RJ-45
port
•flashes slowly as data is transmitted
•flashes quickly if the associated RJ-45 port has been
automatically partitioned.
Power LED
Link/Transmit LEDs
2. SITE CONSIDERATIONS
The site for the 0402 Ethernet Repeater Hub must provide:
•AC power outlet for each Hub
•Adequate ventilation
•Standard environmental conditions
•Isolation from electrical noise, including radio transmitters
and broadband amplifiers, motors, high power electrical
lines, or fluorescent light fixtures.
Additionally:
•The twisted pair cables should not run in the same conduit
with power line cables.
•Phone lines should be separated from data cables.
•Flat or “silver satin”wires should not be used.
And:
•Since the 0400A Ethernet Pocket Hub functions as an
Ethernet Repeater, the entire 0400A Ethernet Repeater Hub
installation should comply with the IEEE Ethernet 802.3
specification, including segment number.
•RJ-45 connected cables should be configured as crossover or
straight through according to installation requirements.

Model 0402 10
5Ethernet™ Pocket Hub™
Connecting Power to 0402 Pocket Hub
To power ON the 0402 Pocket Hub:
1. Locate the power receptacle on the back of the 0402 Pocket
Hub.
2. Connect the 0402 Pocket Hub power connector end of the
power supply adapter to the Pocket Hub.
3. Connect the external power connector end of the power
supply adapter to external AC power.
NOTE: After the power supply adapter is connected to the 0402
Pocket Hub and to external power, the green Power LED is
illuminated.
Ensuring Correct Segmemt Number
Ethernet 802.3 specifications define segment number, as well as cable
characteristics. NOTE: A segment is the cable connection between
cable interfaces in an Ethernet LAN.
Segment Number
When connecting Pocket Hubs, the transmission path between any
two Data Terminating Equipment (DTE) terminals can consist of no
more than five segments.
To assign segment numbers to cable connections:
1. Determine the two terminals in the network which are
separated by the greatest number of segments.
2. Assign a segment path between the terminals by labeling the
cable connected to one of the terminals “segment 1”and the
segment connected to the other terminal “segment n”(n =
total number of segments ≤5).
3. To verify that no segment paths contain more than n segments,
assign segment paths and numbers to all other terminals.
5
3
2
Ethernet™ Pocket Hub™
Ethernet™ Pocket Hub™
Ethernet™ Pocket Hub™
Ethernet™ Pocket Hub™
1
2
4
5
2
3
4
4
5
3
networks
TRANSITION
Mpls,MN 55344
networks
TRANSITION
Mpls,MN 55344
networks
TRANSITION
Mpls,MN 55344
networks
TRANSITION
Mpls,MN 55344

Model 0402 6
9Ethernet™ Pocket Hub™
Ensuring Correct 10BaseT Configuration
The 10BaseT cable and RJ-45 jacks for Hub to Terminal connections
must be configured as straight through. The 10BaseT cable and RJ-45
jacks for Hub to Hub connections must be configured as crossover.
18RJ-45PLUG
RJ-45JACK
18 234567
The two active pairs in a
10BaseT network are pins
1 & 2 and pins 3 & 6. Use
only dedicated wire pairs
(such as blue/white &
white/blue, orange/white
& white/orange) for the
active pins.
Crossover Cable
at RJ-45 Plug
Hub . . . . . . . . . . . . . . .Hub
RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male
1 . . . . . . . . . . . . . . . . . . .3
2 . . . . . . . . . . . . . . . . . . .6
3 . . . . . . . . . . . . . . . . . .1
6 . . . . . . . . . . . . . . . . . .2
Connecting two Pocket Hubs
Use a crossover cable to connect Pocket Hubs.
Use a straight through cable to connect Pocket Hub to terminal
devices.
Connecting Pocket Hub to Terminal Devices
Use a straight through cable to connect Pocket Hub to terminal
devices.
Ethernet™ Pocket Hub™
networks
TRANSITION
Mpls,MN 55344
Ethernet™ Pocket Hub™
networks
TRANSITION
Mpls,MN 55344
#2
Straight-through 10BaseT
Crossover 10BaseT
Ethernet™ Pocket Hub™
networks
TRANSITION
Mpls,MN 55344
#3
Straight-through 10BaseT
Straight Through Cable
at RJ-45 Plug
Hub . . . . . . . . . . . . . . . .PC, transceiver, NIC, printer
RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male
1 . . . . . . . . . . . . . . . . . . .1
2 . . . . . . . . . . . . . . . . . .2
3 . . . . . . . . . . . . . . . . . .3
6 . . . . . . . . . . . . . . . . . . .6

Model 0402 8
7Ethernet™Pocket Hub™
3. INSTALLATION
NOTE: 0402 Ethernet Pocket Hub Link Integrity cannot be
disabled. All devices connected to the Pocket Hub MUST have
link functions enabled.
To install the 0402 Ethernet Pocket Hub:
•Unpack the 0402 Pocket Hub.
•Connect 10BaseT Cable to the 0402 Pocket Hub.
•Connect the 0402 Pocket Hub to power.
Direction is provided in the pages that follow.
Unpacking the 0403 Pocket Hub
The 0402 Ethernet Pocket Hub packing contents should include the
following:
Item Part Number
0402 Pocket Hub E-TBT-HB-0402
Power Supply Adapter 3518, 3517, 3516, 3515, or 3514,
(depending upon power configuration
in country where installed)
User’s Guide 7349
Connecting10BaseT Cable
To connect 10BaseT Cable to Pocket Hub RJ-45 connectors:
1. Locate or build 10BaseT cables with the following
characteristics:
•803.2 compliant (See page 14)
•correct (straight through or crossover) cable configuration
for site installation (See page 7)
•male RJ-45 plug connectors installed at both ends of
cable.
2. Connect male RJ-45 plug connector at one end of 10BaseT
cable to Pocket Hub RJ-45 jack connector.
3. Connect male RJ-45 plug connector at other end of 10BaseT
cable to DTE terminal RJ-45 jack connector (using straight
through cable orientation) or to Pocket Hub RJ-45 jack
connector (using crossover cable orientation).
Connecting to External Hub through Wall Outlet
Use a crossover cable to connect Pocket Hub to the wall plate.
Use a straight through cable to connect Pocket Hub to terminal
devices.
wall plate
#1
Ethernet™ Pocket Hub™
networks
TRANSITION
Mpls,MN 55344
Straight-through 10BaseT
Crossover 10BaseT