Travis Industries 6015 HO GSR2 User manual

6015 HO GSR2
(with screen)
Installation Manual
WARNING: FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Leave the building immediately
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
HOT GLASS WILL CAUSE
BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals.
Tested and Listed by
Report # G100866539PRT-001
ANSI Z21.88a-2014
CSA 2.33a-2014
Built-In Direct Vent
Fireplace
Natural Gas or Propane
Residential or Mobile
Home
This appliance may be installed in an aftermarket, permanently located, manufactured home
(USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. A conversion
kit is supplied with the appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com
Copyright 2014, T.I. $10.00 4140731 100-01366

2 Introduction
© Travis Industries 4140731 100-01366
Overview
This manual details the installation
requirements for the 6015 HO GSR2 fireplace.
For operating and maintenance instructions,
refer to the 6015 HO GSR2 Owner's Manual
(part # 100-01367).
Listing Details
This appliance was listed by Intertek Test Labs
to ANSI Z21.88. The listing label is attached to
the appliance near the gas control valve. A
copy is shown to the right.
Massachusetts Approval
This manual has been submitted to the
Massachusetts Board of State Examiners of
Plumbers and Gas Fitters.
National Fireplace Institute
Report No. G100866539PRT-001
Control No. 4000515
Vented Gas Fireplace Heater
6015 GSR2
Tested to:ANSI Z21.88-2014/CSA 2.33-2014 “Vented Gas Fireplace Heater”, CGA 2.17-M91 (R2009) “Gas Burning Heating Appliances for Manufactured Homes”, and CSAP.4.1-09 Testing method for measuring annual fireplace efficiency. This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSAB149.1. This appliance must be installed in accordance with the current Standard CAN/CSA Z240 MH, Mobile Housing, in Canada or with the Manufactured Home Constructions and Safety Standard, Title 24 CFR, Part 3280, in the UnitedStates,orwhensuch a standard is not applicable,ANSI/NCSBCSA225.1/NFPA501A,ManufacturedHome Installation Standard. Thisvented gas fireplace heateris equipped at thefactory for usewith natural gas. Ifconversion to propane (LP) is desired, the optional factory conversion kit must be used. Part No. 250-02897 register kit may be used. This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket,permanentlylocated, manufactured home(USAonly) ormobilehome, where notprohibitedby local codes. See owner’s manual for details. This appliance is not convertible for use with other gases, unless a certified kit is used. This vented gas fireplace heater is not for use with air filters. Keep burner and control compartment clean. See installation and operating instructions accompanying appliance. This appliance must be properly connected to a venting system in accordance with the manufacturer’s installation instructions. Use only approved coaxial direct vent system to vent this appliance to the exterior. See owner’s manual for approved brands of venting. If the vent-air intake system is disconnected for servicing or any other reason, it must be resealed and / or reinstalled. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier. VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUEL
Minimum Clearances to Combustibles
Fireplace to Adjacent Wall Wood Floor Beneath Fireplace Back to Enclosure
3” (77mm)
0” (0mm)
0.125” (4mm)
Base of Fireplace to Enclosure Top Sides to Enclosure Base of Fireplace to a Mantel
66” (1676mm)
0.625” (17mm)
See Owner’s Manual
FAN TYPE VENTED CIRCULATOR
Blower Electrical Rating: 120V., 4.5 Amps, 60 Hz, 540 Watts
Part No. 250-02898 / 250-02899 fan or blower assembly may be used.
DANGER! Risk of Electric Shock. Disconnect power before servicing unit.
Minimum Inlet Pressure (inches W.C.) Maximum Inlet Pressure (inches W.C.) Manifold Pressure on “HI” (inches W.C.)
L.P.
11”
13”
11”
N.G.
5.5”
7”
3.8”
Input Rate on “HI” (BTU/Hr) Input Rate on “LO” (BTU/Hr) Orifice Size - Left (DMS) Orifice Size - Right (DMS)
L.P.
56,000 29,626
#53 #53
N.G.
56,000 30,273
2.5mm 2.5mm
This appliance is equipped for use only at altitudes 0-2,000 feet (0-610m) in the USA. In Canada, 0-4,500 feet (0-1370m). For altitudes above 2,000 feet, the vent configuration, orifice, or combination of both may need to be changed. See owner’s manual for information on making these changes.
2015 2016 2014
Feb. Mar. Jan.
May Jun. Apr.
Aug. Sep. Jul.
Nov. Dec. Oct.
MANUFACTURE DATE:
WARNING: Failure to install this appliance per the manufacturer’s instructions or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.
12521 Harbour Reach Drive
Mukilteo, WA 98275
Manufactured by:
www.travisproducts.com
CAUTION:
Do not operate this appliance with glass removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.
1078

Table of Contents 3
© Travis Industries 4140731 100-01366
Overview ................................................................... 2
Listing Details........................................................... 2
Installation Options.................................................. 6
Heating Specifications............................................. 6
Dimensions............................................................... 6
Packing List .............................................................. 7
Additional Items Required....................................... 7
Recommended Installation Procedure................... 7
Massachusetts Requirements ................................ 8
Requirements for the Commonwealth of
Massachusetts.................................................................8
MANUFACTURER REQUIREMENTS.............................8
Fireplace Placement Requirements ....................... 9
Clearances ......................................................................9
Raised Fireplaces............................................................9
Televisions (or other electronics) Placed Near the
Fireplace..........................................................................9
Televisions Placed Above the Fireplace................ 10
Using a Mantel Between the Fireplace and Television....10
Using a Recessed Fireplace Below a Television.............11
Using a Recessed Fireplace with a Recessed
Television ........................................................................12
Minimum Framing Dimensions – NG (all
configurations) or LP with 36” Rise (or greater)... 13
Preparing the Vertical Supports for 66” Tall
Framing ..................................................................... 13
Minimum Framing Dimensions – LP with
Minimum Vent (24” Rise)......................................... 14
Nailing Brackets – Extended (Tile Over) Install ....15
Nailing Brackets – Flush Install.............................. 16
Corner Installations.................................................. 17
Removing the Front Panel....................................... 18
Gas Line Requirements........................................... 19
Fuel .................................................................................19
Gas Line Connection.......................................................19
Gas Inlet Pressure...........................................................19
Directions for Connecting a Gas Pressure Test Gauge...19
Gas Line Location............................................................20
Relocating the Gas Line to the Baseplate ......................20
Electrical Connection............................................... 21
Relocating the Electrical Line to the Baseplate ..............21
Vent Requirements................................................... 22
Vent Clearances..............................................................22
Vent Firestop...................................................................22
Altitude Considerations....................................................22
Approved Vent.................................................................22
Vent Installation...............................................................22
Vertical Pipe Shield .........................................................23
Minimum Vent Pipe Shield – Used for Minimum Vent
Applications Only.............................................................24
Horizontal Termination Exhaust Shield............................25
Approved Vent Configurations...............................26
Restrictor Position...........................................................26
Exhaust Restrictor...........................................................26
Intake Restrictor..............................................................27
Diffuser............................................................................28
Minimum Vent Configuration ..................................29
NG Vent Configurations – Vertical Termination....30
NG Vent Configurations – Horizontal
Termination (Min. 30” Rise).....................................31
LP Vent Configurations – Vertical Termination.....32
LP Vent Configurations – Horizontal
Termination (Min. 36” Rise).....................................33
Termination Requirements......................................34
Hearth Requirements...............................................35
Drywall Supports......................................................35
Facing Requirements – Flush Install......................36
Facing Requirements...............................................37
Do Not Drill or Screw Zone..............................................38
Mantel Requirements...............................................39
Mantel Column Clearances...........................................39
Steps for Finalizing the Installation........................40
Air Shutter Adjustment ....................................................41
Glass Frame Removal and Installation ..................42
Fireback Installation.................................................44
Crushed Glass Installation......................................46
LP Conversion Instructions ....................................47
Wiring Diagram.........................................................51
Power Heat Duct Installation...................................52

4 Safety Precautions
© Travis Industries 4140731 100-01366
Safety Warnings
Failure to follow all of the requirements may result in property damage, bodily injury, or even death.
Young children should be carefully supervised when they are in the same room
as the appliance. Toddlers, young children and others may be susceptible to
accidental contact burns. A physical barrier is recommended if there are at risk
individuals in the house. To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children and other at risk
individuals out of the room and away from hot surfaces.
Children and adults should be alerted to the hazards of high surface temperature
and should stay away to avoid burns or clothing ignition. Do not touch the hot
surfaces of the heater. Educate all children of the danger of a high-temperature
heater.
Due to the high temperature, the heater should be located out of traffic and away
from furniture and draperies.
This unit must be installed by a qualified installer to prevent the possibility of an explosion.
This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI
Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.
A manufactured home (USA only) or mobile home OEM installation must conform with the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a
standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS
A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This
appliance may be installed in Manufactured Housing only after the home is site located.
All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn
from outside the living-area structure. The venting must not be connected to a chimney flue serving a
separate solid-fuel burning appliance.
Notify your insurance company before hooking up this fireplace.
The instructions in this manual must be strictly adhered to. Do not use makeshift methods or
compromise in the installation. Improper installation will void the warranty and safety listing.
This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will
void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about
the type of fuel used to your dealer.
Contact your local building officials to obtain a permit and information on any installation restrictions
or inspection requirements in your area.
If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call
your dealer and arrange for proper servicing.
It is imperative that control compartments, screens, or circulating air passageways of the heater be
kept clean and free of obstructions. These areas provide the air necessary for safe operation.
Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call
your dealer for a full explanation of your heater and what to expect.
Do not store or use gasoline or other flammable liquids in the vicinity of this heater.
Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.
Immediately call a qualified service technician to inspect the appliance and to replace any part of the
control system and any gas control which has been under water.

Safety Precautions 5
© Travis Industries 4140731 100-01366
Safety Warnings (continued)
Because this heater can be controlled by a thermostat there is a possibility of the heater turning on
and igniting any items placed on or near the appliance.
Light the heater using the built-in igniter. Do not use matches or any other external device to light
your heater.
Never remove, replace, modify or substitute any part of the heater unless instructions are given in this
manual. All other work must be done by a trained technician. Don't modify or replace orifices.
The viewing glass should be opened only for conducting service.
Allow the heater to cool before carrying out any maintenance or cleaning.
Operate the heater according to the instructions included in this manual.
If the main burners do not start correctly turn the gas off and call your dealer for service.
This unit is not for use with solid fuel.
Do not place anything inside the firebox (except the optional artwork).
Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement
of the glass should be done by a licensed or qualified service person.
Do not throw this manual away. This manual has important operating and maintenance instructions
that you will need at a later time. Always follow the instructions in this manual.
Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.
The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to
shut off.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this
appliance.
Clothing or other flammable material should not be placed on or near the appliance.
Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to
operating the appliance.
Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent cleaning
might be required due to excessive lint from carpeting, bedding material, et cetera. It is imperative
that control compartments, burners, and circulating air passageways of the appliance be kept clean.
Travis Industries, Inc. grants no warranty, implied or stated, for the installation or
maintenance of your heater, and assumes no responsibility of any consequential damage(s).

6 Features and Specifications
© Travis Industries 4140731 100-01366
Installation Options
Residential or Mobile Home
Straight or Corner Placement
Raised or Floor Placement
Internal or External Chase
Bedroom Approved
Heating Specifications
Natural Gas Propane
Approximate Heating Capacity (in square feet)* Up to 2,800 Up to 2,800
Maximum BTU Input Per Hour 56,000 56,000
* Heating capacity will vary with floor plan, insulation, and outside temperature.
Dimensions
Left
a' gauche
Front
avant
Right
droit
Rear
arrie're
64-3/4" *
1645mm *
LP Min. Vent
Installations:
72"
1829mm
All Other
Installations:
66"
1677mm
37-3/8"
924mm
1"
25mm
1/2"
12mm
* Includes the requisite clearance to framing (1/8"
4mm to rear, 5/8" 16mm to the sides)
10-3/8"
264mm
15-3/4"
401mm
11-1/4"
286mm
7-5/8"
194mm
34-3/4"
883mm
1556mm
61-1/4"
350 lbs.
156 Kg.
17" *
432mm *

Installation (for qualified installers only) 7
© Travis Industries 4140731 100-01366
Packing List
Propane Conversion Parts
Remote Control
4 AA Batteries, 3 AAA Batteries
Glass Latch Tool
(2) Firestops (8” Diameter)
Top Drywall Support
Minimum Vent Pipe Shield
Horizontal Termination Exhaust Shield
Additional Items Required
If using LP (propane) a conversion kit is required (sku 94400999 – GSR Stepper Motor Kit).
Gas Line Equipment (shutoff valve, pipe, etc.)
Electrical Equipment (min. 14 gauge, grounded line)
This Fireplace Requires Firebacks and 10 lbs. of 1/4” Crushed Glass
Firebacks 96100981 Stainless Steel
96100982 Black Enamel
96100983 Black Painted
96100984 Ledgestone
Crushed Glass 94500580 Platinum (10 lbs.)
94500581 Bronze (10 lbs.)
94500582 Cobalt (10 lbs.)
Recommended Installation Procedure
Frame the opening for the fireplace. Make sure to allow for vent installation.
This fireplace is designed to accommodate 1/2" (13mm) drywall (see "Nailing Brackets" on page 13 for
details). Secure the fireplace to the framing.
Install the vent, gas line and electrical hook-up.
Install the drywall.
Install the hearth (if applicable).
Install the facing (if applicable).
Install the mantel (if applicable).
Finalize the installation (see page 39).

8 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Massachusetts Requirements
NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.
Requirements for the Commonwealth of Massachusetts
For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in
part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent
termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and
porches, the following requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall
observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the
gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard
wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served
by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the
services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired
carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day
period, a battery operated carbon monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be
ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or
equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP
CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.
Exemptions
The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54
as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or
venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment
and the venting system shall include:
• Detailed instructions for the installation of the venting system design or the venting system components; and
• A complete parts list for the venting system design or venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for
venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions shall be included with the appliance or equipment installation
instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list
and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Installation (for qualified installers only) 9
© Travis Industries 4140731 100-01366
Fireplace Placement Requirements
Fireplace must be installed on a level surface capable of supporting the fireplace and vent
Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)
Fireplace should be located out of traffic and away from furniture and draperies.
Fireplace must be placed so the gaps below and above the glass frame do not become blocked.
Fireplace may be placed in a bedroom. Please be aware of the large amount of heat this appliance produces
when determining a location.
Clearances
(a) Clearance to Side of Fireplace 5/8” (16mm). Do not place insulation in this space.
NOTE: Drywall or other combustible may contact the side of the fireplace in front of the framing. The
material must not protrude in front of the fireplace and may be a maximum ½” (13mm) thick.
(b) Clearance to Back of Fireplace 1/8” (4mm). Do not place insulation in this space.
(c) When installed, walls in front of the fireplace must be a minimum 3” (77mm) to the side of the fireplace.
Raised Fireplaces
The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace and vent.
The base of the fireplace must be a minimum 66” below the room ceiling.
The firebox opening is approximately 10.375” (264mm) above the base of the fireplace. For a
typical raised fireplace of 36” (915mm), place the fireplace on a platform 25.625” (651mm) tall.
LP MIN VENT APPLICATIONS: Framing opening for LP min vent applications is 72” (1829mm).
MAKE SURE TO ACCOMMODATE THE REQUIRED FRAMING OPENING.




a
c
b

10 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Televisions Placed Above the Fireplace
The following section details three methods to allow for television installation above the fireplace.
Using a Mantel Between the Fireplace and Television
IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE
Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may
negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,
please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to
reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take
responsibility for any negative impact to televisions placed near this fireplace.
Minimum Dimensions:
(a) Mantel Height above Base of Fireplace
Mantel must fall within shaded portion of the chart above. 42” (1067mm) with 8” (203mm) mantel depth See chart above if using a larger mantel.
(b) Mantel Depth* Minimum 8” (203mm)
* NOTE: The minimum mantel depth is 8”. This allows heat to travel forward and dissipate.
EXAMPLES: If you have a TV that is greater than 6” deep (including the 1” gap behind), you will need to alter the mantel
depth and height. If your TV is 9” deep (including the 1” gap behind), the mantel should be 11” (this provides the necessary 2”
recess for the TV). The 11” mantel would require a 43.5” (292mm) mantel height (see chart above).
WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to
protect from contact with hot surfaces.
a
Fireplace
Min. 2" (51mm)
From Front of TV
Mantel Must be
Min. 1" (26mm) Thick
Min. 1" (26mm) Air Gap Behind TV
(typically provided by wall mount)
b
Min. 1" (26mm)
Television (TV)
(b) Depth
(a)
Height
Above
Base of
Fireplace
46" (1169mm)
0" (0mm)
1" (25mm)
2" (51mm)
8" (203mm)
7" (178mm)
6" (152mm)
5" (127mm)
4" (102mm)
3" (76mm)
9" (229mm)
10" (254mm)
11" (279mm)
12" (305mm)
45" (1143mm)
44" (1118mm)
43" (1093mm)
42" (1067mm)
41" (1042mm)
47" (1194mm)

Installation (for qualified installers only) 11
© Travis Industries 4140731 100-01366
Using a Recessed Fireplace Below a Television
IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE
Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may
negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,
please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to
reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take
responsibility for any negative impact to televisions placed near this fireplace.
Minimum Dimensions:
(a) Fireplace Recess Height above Base of Fireplace
Recess must fall within shaded portion of the chart above. 42” (1067mm) with 8” (203mm) recess depth See chart above if using a larger recess.
(b) Fireplace Recess Depth plus Mantel Depth* Minimum 8” (203mm)
(c) Fireplace Recess Width 69.5” (1766mm)
* NOTE: The minimum recess plus mantel depth is 8”. This allows heat to travel forward and dissipate.
EXAMPLES: If you have a TV that is 3” deep (including the 1” gap behind), you will need to put in a 5” mantel (the 2” is
measured from the front of the TV). The fireplace can then be recessed 3” into the wall to allow for the 8” of recess plus
mantel depth.
WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to
protect from contact with hot surfaces.
b
Fireplace
Min. 1" (26mm) Air Gap Behind TV
(typically provided by wall mount)
Television (TV)
Min. 6"
(152mm)
a
Min. 2" (51mm)
From Front of TV Min. 1" (26mm)
c
Min. 6"
(152mm)
(b) Depth
(a)
Height
Above
Base of
Fireplace
46" (1169mm)
0" (0mm)
1" (25mm)
2" (51mm)
8" (203mm)
7" (178mm)
6" (152mm)
5" (127mm)
4" (102mm)
3" (76mm)
9" (229mm)
10" (254mm)
11" (279mm)
12" (305mm)
45" (1143mm)
44" (1118mm)
43" (1093mm)
42" (1067mm)
41" (1042mm)
47" (1194mm)

12 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Using a Recessed Fireplace with a Recessed Television
IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE
Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may
negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,
please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to
reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take
responsibility for any negative impact to televisions placed near this fireplace.
Minimum Dimensions:
(a) Fireplace Recess Height above Base of Fireplace
Recess must fall within shaded portion of the chart above. 42” (1067mm) with 8” (203mm) recess depth See chart above if using a larger recess.
(b) Fireplace/TV Recess Depth* Minimum 8” (203mm)
(c) Fireplace Recess Width 69.5” (1766mm)
* NOTE: The minimum recess depth is 8”. This allows heat to travel forward and dissipate.
EXAMPLES: If you have a TV that is greater than 6” deep (including the 1” gap behind), you will need to alter the fireplace
recess depth and height. If your TV is 9” deep (including the 1” gap behind), the recess should be 11” (this provides the
necessary 2” recess for the TV). The 11” recess would require a 43.5” (292mm) fireplace recess height (see chart above).
If you have a TV that is 3” deep (including the 1” gap behind), you will need to put in a 5” mantel (the 2” is measured from the
front of the TV). The fireplace can then be recessed 3” into the wall to allow for the 8” of recess plus mantel depth.
WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to
protect from contact with hot surfaces.
b
a
Fireplace
NOTE: These
two walls are
at the same
depth.
Min. 1" (26mm) Air Gap Behind TV
(typically provided by wall mount)
Television (TV)
Min. 3"
(77mm)
Min. 6"
(152mm) Min. 2" (51mm)
From Front of TV
c
b
(b) Depth
(a)
Height
Above
Base of
Fireplace
46" (1169mm)
0" (0mm)
1" (25mm)
2" (51mm)
8" (203mm)
7" (178mm)
6" (152mm)
5" (127mm)
4" (102mm)
3" (76mm)
9" (229mm)
10" (254mm)
11" (279mm)
12" (305mm)
45" (1143mm)
44" (1118mm)
43" (1093mm)
42" (1067mm)
41" (1042mm)
47" (1194mm)

Installation (for qualified installers only) 13
© Travis Industries 4140731 100-01366
Minimum Framing Dimensions – NG (all configurations) or LP with 36” Rise
(or greater)
The fireplace enclosure
must be a minimum 66”
tall (do not build into the
fireplace enclosure)
Preparing the Vertical Supports for 66” Tall Framing
a
66"
1677mm
66"
1677mm
64-3/4"
1645mm
17" 432mm Flush Install
16-1/2" 420mm Extended (Tile Over) Install
a
Remove and discard top sections on the vertical
supports (use tin snips or pliers to remove).
WARNING: Sheet metal edges are sharp.

14 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Minimum Framing Dimensions – LP with Minimum Vent (24” Rise)
The fireplace enclosure must be a minimum 72” (1829mm) tall (do not build into the fireplace enclosure)
a
72"
1829mm
64-3/4"
1645mm
72"
1829mm
17" 432mm Flush Install
16-1/2" 420mm Extended (Tile Over) Install
a

Installation (for qualified installers only) 15
© Travis Industries 4140731 100-01366
Nailing Brackets – Extended (Tile Over) Install
The fireplace has nailing brackets on both sides. Secure the fireplace to the framing.
NOTE: Make sure the fireplace is square and plumb when placed in the framing. Measured corner-to-corner
the fireplace should be square. Use shims to insure the fireplace is square.
Bend the three
nailing brackets
out (each side)
NOTE: if you can not use the
front nailing brackets, an
additional bracket is supplied on
the side that allows the fireplace
to be secured to the floor (bend
tab down and secure).
Secure the fireplace to
the framing using the
nailing brackets
Nailing Bracket
This 5/8" (16mm)
tab acts as a
standoff and helps
center the fireplace
in the framing)

16 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Nailing Brackets – Flush Install
The fireplace has nailing brackets on both sides. Secure the fireplace to the framing.
NOTE: Make sure the fireplace is square and plumb when placed in the framing. Measured corner-to-corner
the fireplace should be square. Use shims to insure the fireplace is square.
Bend the side nailing brackets as shown below.
NOTE: if you can not use the
front nailing brackets, an
additional bracket is supplied on
the side that allows the fireplace
to be secured to the floor (bend
tab down and secure).
Secure the fireplace to
the framing using the
nailing brackets and
vertical drywall support.
Bend the vertical drywall support forward.
The mounting hole is now vertical and may
be secured to the framing from below.
Bend the top nailing bracket
as shown until it is flush with
the front of the fireplace.
ca b
Rotate the bracket on the
rivet 180 degrees.

Installation (for qualified installers only) 17
© Travis Industries 4140731 100-01366
Corner Installations
A typical 45° installation uses the framing dimensions shown in the illustration below (NOTE: all clearances still
apply).





























69" Min.
1753mm
Minimum 5/8" (16mm) Clearance





Typically
29"
737mm


















18 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Removing the Front Panel
The front cover may be removed to access the components. This is required when relocating the electrical or gas
inlet location. To remove the front cover
(a) Remove the
center nut.
(b) Loosen the
two outer
nuts.
(c) Rotate the
front panel
down.
(d) Remove the
front cover.
11/32" Nutdriver/Wrench

Installation (for qualified installers only) 19
© Travis Industries 4140731 100-01366
Gas Line Requirements
MASSACHUSETTS INSTALLATIONS - WARNING:
THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUMBER OR GAS FITTER WHEN INSTALLED WITHIN THE
COMMONWEALTH OF MASSACHUSETTS.
OTHER MASSACHUSETTS CODE REQUIREMENTS:
Flexible connector must not be longer than 36 inches.
Shutoff valve must be a “T” handle gas cock.
Only direct vent sealed combustion products are approved for bedrooms or bathrooms.
Fireplace dampers must be removed or welded in the open position prior to the installation of a fireplace insert or gas log.
A carbon monoxide (CO) detector is required in the same room as the appliance.
The gas line must be installed in accordance with all local codes, if any; if not, follow ANSI 223.1 and NFPA
54(88), in Canada follow CSA B149.1 and the requirements listed below.
The fireplace and gas control valve must be disconnected from the gas supply piping during any pressure
testing of that system at test pressures in excess of 1/2 psig (3.5 kPA). For pressures under 1/2 psig (3.5
kPA), isolate the gas supply piping by closing the manual shutoff valve.
Leak test all gas line joints and the gas control valve prior to and after starting the fireplace.
This unit has been listed using the included internal gas shutoff valve.
Fuel
This fireplace is designed either for natural gas or for propane (but not for both).
Gas Line Connection
Installation must be performed by a qualified installer, service agency or the gas supplier (In Massachusetts a licensed
plumber/gasfitter).
Gas Inlet Pressure Maximum Input Pressure Minimum Input Pressure
Natural Gas 7" W.C. (1.74 kPA) 5.5” W.C. (1.37 kPA)
Propane 13" W.C. (3.23 kPA) 11” W.C. (2.74 kPA)
If the pressure is not sufficient, make sure the piping used is large enough, the supply regulator is adequately adjusted,
and the total gas load for the residence does not exceed the amount supplied.
The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should supply gas
at the input pressure listed above. Contact the local gas supplier if the regulator is at an improper pressure.
Directions for Connecting a Gas Pressure Test Gauge
The gas control valve (shown to the left) has two accessible ports for testing
line pressure and output pressure. Loosen the brass screw on either test port
and place a 5/16” i.d. rubber or plastic tubing over the tapered test port.
Connect the tubing to the test gauge.
WARNING: The brass screw must be tightened after testing to prevent gas
leakage.
Input pressure
Output pressure

20 Installation (for qualified installers only)
© Travis Industries 4140731 100-01366
Gas Line Location
NOTE FOR RIGID PIPE: When using rigid pipe, you may wish to disconnect the shutoff valve from the fireplace
and route the pipe through the fireplace wall. First, disconnect the gas line from the shutoff valve (see step 1
below). Then remove the shutoff valve from the cover plate (4 screws outside fireplace). The pipe may be routed
through the cover plate and the shutoff valve and gas line may be re-attached inside the fireplace.
Gas line may be plumbed from the left side (stock) or below. See illustration and table below to determine gas line location.
a b
Left Side Gas Line Location (Stock) 4” (102mm) 3.25” (83mm)
Baseplate Gas Line Location 5.5” (140mm) 27” (686mm)
Relocating the Gas Line to the Baseplate
1. Disconnect the gas line from the shutoff valve (3/4” wrench). Gas line is located inside the fireplace on the left side.
2. Remove the screw that holds the shutoff valve plate in place (1/4” nutdriver). Remove the shutoff valve plate.
3. Remove the cover plate from the bottom of the fireplace (it is held in place in the same fashion as the shutoff valve plate).
Attach it to the left side of the fireplace.
4. Attach the shutoff valve plate to the bottom of the fireplace. Route the gas line to the bottom and re-attach the gas line to
the shutoff valve. Make sure to leak test the entire gas line.
Framing Opening
a
b
a
b