Travis Industries GreenSmart Fireplace 564 SS User manual

564 SS Fireback Installation
SKU # 96100179 (Brick / Herringbone) SKU # 96100182 (Diamond / Stucco)
SKU # 96100181 (Seattle Rock Creek) SKU # 96100183 (Basket Weave / Quilt)
SKU # 96100270 (Handmade Brick) SKU # 96100271 (Reclaimed Brick)
Page 1 of 2 17601465 - 9/22/10 Travis Industries, Inc.
Packing List
• Rear Fireback
• (2) Side Firebacks
• (2) Floor Firebacks
Installation
WARNING Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.
NOTE On two-sided firebacks make sure to use the desired pattern.
1 Remove the glass frame and logs (see the installation manual for details).
2 Remove the grate (replace after fireback installation). Remove and discard the hearth plate.
Remove the grate
(replace after fireback installation).
1/4" Nutdriver
AA
AA
A
A
AA
AA
AA
AA
Remove and discard
the hearth plate
Loosen this screw and
slide the bracket up.

564 SS Fireback Installation
SKU # 96100179 (Brick / Herringbone) SKU # 96100182 (Diamond / Stucco)
SKU # 96100181 (Seattle Rock Creek) SKU # 96100183 (Basket Weave / Quilt)
SKU # 96100270 (Handmade Brick) SKU # 96100271 (Reclaimed Brick)
Page 2 of 2 17601465 - 9/22/10 Travis Industries, Inc.
3 Install the firebacks following the directions below.
AA
AA
AA
AA
Place the rear fireback in place. The side
fireback holds the rear fireback in place -
hold the rear fireback while installing the
side fireback.
Remove the clip located on the
firebox ceiling near the front (both
sides). The side fireback clip has
a keyhole slot. It can be removed
by loosening the screw and
sliding the clip out.
Place the side firebacks
in place.
a
AA
AA
AA
AA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
1/4" Nutdriver
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
c
Replace the clips removed in
step “a” to secure the side
firebacks..
e
d
NOTE: Place the fireback
so the vertical grout line on
the edge of the fireback is
facing the rear.
Loosen this screw and slide the bracket up. Place the floor
firebacks in place (under the bracket). Slide the bracket
down and tighten the screw to secure the firebacks.
b
Due to the construction of the ceramic firebacks, you may need to re-position the
firebacks to achieve the correct alignment.
4 Restore the fireplace to the correct configuration.