TRENDnet TDM-C400 User manual

TDM-E400
TDM-C400
Quick Installation Guide

Table of Contents
Table of Contents
Version 09.07.2006
English .......................................................................................................
Troubleshooting ........................................................................................
1
1
3
4
7
10
1. Before You Start
2. .........................................................................
3.
..................................................................................
Hardware Installation .
Software Installation (TDM-C400 only) ...............................................
4. Configuring the ADSL Modem through Ethernet or USB connection ..

Installation Requirements
Application
ADSL/ADSL2/ADSL2+ service up and running on your telephone line.
Package Content
1. Before You Start
English
1
TDM-E400/TDM-C400
CD-ROM (User's Guide)
Quick Installation Guide
1 x RJ-45 Cat.5 Cable
1 x USB Cable (for TDM-C400 only)
1 x RJ-11 Telephone Cable
Power Adapter (15V DC 1A)
One or more computers each containing an Ethernet 10Base-T/100Base-T
network interface card (NIC) and/or a single computer with a USB port
An Ethernet hub or switch, if you are connecting the device to more than
one computer on an Ethernet network
Web browser: Internet Explorer v5.0 or later, or Netscape v6.1 or later
ADSL Enabled Phone Jack
ADSL/ADSL2+ Ethernet Modem Router (TDM-E400)
ADSL/ADSL2+ Ethernet/USB Combo Modem Router (TDM-C400)
Workstations with10/100Mbps
Fast Ethernet PCI Adapter
(TE100-PCIWN)
5-port 10/100Mbps
Fast Ethernet Switch
(TE100-S5P)
Workstation with 10/100Mbps
Fast Ethernet PCI Adapter
(TE100-PCIWN)
Stand-Alone PC
Internet
(TDM-C400 only)

English
2
Collect the following information from your
ADSL2+ service provider
VPI value: ______
VCI value: ______
Encapsulation type: □LLC/SNAP or □VC/MUX
As well as:
For PPPoA (RFC2364) or PPPoE (RFC2516)
User Name: _______________________
Password: ________________________
Authentication method: □PAP or □CHAP
Host or IP address: _________________
For Static or Fixed IP Connectin (RFC1483 or RFC1577)
Host: ____________________________
Domain: __________________________
Gateway: _________________________
IP address: _______________________
Subnet Mask: _____________________
DHCP Server IP : __________________
Primary DNS Server IP: ______________________
Secondary DNS Server IP: ____________________

English
3
2. Hardware Installation
3. Attach the power connector to the
ADSL2+ ethernet router.
2. Connect the RJ-45 cable (and/or
connect the USB cable for
TDM-C400 USB combo Model
only).
1. Connect the RJ-11 cable.
4. Allow the device 60 seconds to
boot. Verify that the WAN and LAN
LEDs are on.

English
4
3. Software Installation (TDM-C400 only)
Note: For Windows 98/98SE applications, you may need the Windows
98/98SE CD ROM to complete the installation.
Before starting the software setup process, close all Windows programs
currently running on your PC.
1. The system automatically detects
the new hardware when the USB
cable is connected to your PC
Click Cancel.
(Windows 98/98SE)
(Windows 2000)
(Windows ME)
(Windows XP)
2. Insert the installation CD into the
CD drive and click on the USB
Utility button sub menu
"TDM-C400". The installation
should start.

English
5
3. The “Welcome!” windows appears.
Exit all Windows programs before
continuing. Then, click on Next.
4. Please review the license
agreement and click Accept to
continue.
5. The USB Modem Setup Wizard will
begin installing the software and
indicates the progress of the
installation.
6. If the installation wizard detects
that the ADSL modem is not
connected by USB, it prompts you
to connect it in order to proceed.

7. A message will be displayed
requiring you to reboot the system.
Select “Yes, reboot the computer
now” and then click Close.
9. From Programs, go to TRENDnet
DSL Modem and click on the DSL
Status.
English
6
8. After rebooting, the device will be
installed. Please click Finish.
10. The “Physical Link” tab of the
“TRENDnet DSL Modem” window
(Control Panel) allows you to
review the current state of the
TRENDnet DSL Modem and
connection. The State field will
indicate that the TDM-C400 is
“Connected”.

English
7
Note: The DHCP server of the ADSL2+ modem router is enabled by default.
Please configure your computer to automatically obtain an IP address from the
ADSL2+ modem router’s DHCP Server.
2. Enter User name and Password,
and then click OK. By default,
User name: admin
Password: admin
1. Open your web browser, type
http://192.168.1.254 in the
Address bar, and press Enter.
3. The System View page displays
each time you login to the Web-
Configuration. Click Quick
Configuration to start
configuration procedures.
4. Configuring the ADSL Modem through Ethernet
or USB connection

English
8
4. The Quick Configuration table will
appear requiring you to fill in the
fields with the appropriate
information provided by your
Service Provider.
5. Then click the Submit button.
6. Click Admin in the Web
Configuration screen.
7. Click Commit & Reboot.
8. Click Commit.