TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M User manual

TEW-435BRM
Quick Installation Guide

Table of Contents
Table of Contents
Version 06.19.2006
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
3
4
7
1. Before You Start
2. Install Hardware .................................................................................
3. .................................................................
.................................................................................
Configuration The Modem

Installation Requirements
Application
A working DSL Internet Connection
A computer with a wired or wireless network adapter properly installed.
Package Content
1. Before You Start
English
1
TEW-435BRM
Quick Installation Guide
User's Guide CD-ROM
1 x 2dBi Detachable Antenna
1 x RJ-45 Ethernet Cable (Yellow)
1 x RJ-11 Telephone Cable (Gray)
Mounting Stand
Power Adapter
Web Browser: Internet Explorer (5.0 or higher) or Netscape Navigator
(4.7 or higher)
10/100Mbps
Phone Jack
ADSL Account
Ready Line
Internet
Notebook with
Wireless PC Card
(TEW-421PC)
54Mbps 802.11g ADSL
Modem Router
(TEW-435BRM)
Workstation with
Wireless PCI Adapter
(TEW-423PI)
Workstation with
PCI Adapter
(TE100-PCIWN)
54Mbps

English
2
Collect Internet Service Provider (ISP) Information
During the installation of your Wireless ADSL Modem Router, the Setup Wizard
will automatically detect your ISP connection type. If the router cannot detect
your ISP connection type, you can manually specify the connection type.
Please verify your DSL Internet broadband connection type with your ISP and
ensure you have all the information for one of the following connection types:
A. Dynamic IP connection
ADSL Modem parameters (VPI or VCI), if it cannot be detected automatically.
ISP may require you to use a particular Hostname or Domain name.
B. Static or Fixed IP connection
Internet IP Address:_____. _____._____._____ (eg. 215.24.24.129)
Subnet Mask: _____. _____._____._____
Gateway IP Address: ____. _____._____._____
Primary DNS:_____. _____._____._____
Secondary:_____. _____._____._____
ADSL Modem Parameters (VPI or VCI), if it cannot be detected automatically.
C. PPPoE or PPPoA Dynamic IP connection
Login User Name: _________
Password: ________________
ADSL Modem Parameters (VPI or VCI), if it cannot be detected automatically.
D. IPoA Static or Fixed (IP over ATM) connection
Internet IP Address:_____. _____._____._____ (eg. 215.24.24.129)
Subnet Mask: _____. _____._____._____
Gateway IP Address: ____. _____._____._____
Primary DNS:_____. _____._____._____
Secondary:_____. _____._____._____.
ADSL Modem Parameters (VPI or VCI), if it cannot be detected automatically.

English
3
2. Hardware Installation
2. Connect one end of the yellow RJ-
45 cable to one of the
TEW-435BRM's LAN ports.
Connect the other end of cable to
the computer's Ethernet port. Then
connect the 2dBi detachable
antenna.
4. Connect the AC Power Adapter to
the TEW-435BRM and then to a
power outlet.
1. Attach the mounting stand to the
side of the unit.
5. Verify that the following panel lights
are on: Power, LAN, and WLAN.
3. Connect one end of the gray RJ-11
cable to the TEW-435BRM's ADSL
port. Connect the other end of the
cable to the phone jack.

English
4
3. Configure the Modem
Note: It is recommended that you configure the Modem from a wired computer.
2. Enter User name and Password,
and then click OK. By default,
User name: admin
Password: password
1. Open your web browser, type
http://192.168.0.1 in the
Address bar, and press Enter.
3. Click Setup Wizard.

English
5
5. Select Auto-detect, and then click
Next.
Note: In the example, the DSL connection is PPPoE.
4. Click Next.
6. Wait for the Auto Detection process
to complete.

Note: If the Setup Wizard could not automatically detect your Internet
connection, select Manual Selection and input the information using the
information provided by your ISP.
Note: For other connection methods, follow the on screen instructions after the
Auto Detection.
7. Configure the settings based on
information provided by your ISP.
Then click Next.
9. Verify that the ADSL LED is lit and
then click Close.
Your installation is now complete.
For detailed information regarding the TEW-435BRM's configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.
English
6
8. Check Test Internet Connection,
and then click Finish.

7
Troubleshooting
Q1:
A1:
I typed http://192.168.0.1 in my Internet Browser's Address Bar, but an error
message says “The page cannot be displayed.” How can I get into the
TEW-435BRM's web configuration page?
First, check your hardware settings again by following the instructions in
Section 2. Second, make sure the LAN and WLAN lights are lit. Third, make sure
your TCP/IP settings are set to Obtain an IP address automatically (see the
steps below).
1. Go into the Control Panel and double-
click the Network Connections icon,
right-click the Local Area Connection
icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and
then click Properties. Then click on
Obtain an IP address automatically.
Fourth, press on the factory reset button for 15 seconds.
The Modem does not auto-detect my DSL connection. What should I do?
First, verify that your DSL account is activated. Second, make sure all the
cables are properly connected (see Section 2). Third, in Section 3, select manual
selection in the Setup Wizard and configure the Modem based on information
provided by your ISP.
Q2:
A2:

8
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you
LocalAuthority or Retailer for recycling advice.
Q3:
A3:
All the settings are correct, but I can not make a wireless connection to the
Modem. What should I do?
First, double check that the WLAN light on the Modem is lit. Second, power
cycle the Modem. Unplug the power to the Modem. Wait 15 seconds, then plug
the power back in. Third, log into your Modem (see Section 3). Click on Wireless
and make sure Enable Access Point is checked. Fourth, contact the
manufacturer of your wireless network adapter. Make sure the wireless network
adapter is configured with the proper SSID. The preset SSID of the Access Point
is default.
If you still encounter problems or have any questions regarding the TEW-435BRM,
please contact TRENDnet's Technical Support Department.