TRENDnet TSE-IS401 User manual

TSE-IS401
Quick Installation Guide

Table of Contents
Table of Contents
Version 10.27.2006
Français ....................................................................................................
Troubleshooting ........................................................................................
1
1
2
5
6
1. Avant de commencer ........................................................................
2. ......................................................................Installation du matériel
3. Accès aux périphériques de stockage sur TSE-IS401 ......................

1
Configuration du système
1. Avant de commencer
Français
Application
TSE-IS401
Guide d'installation rapide
Adaptateur secteur (12DC, 2A)
Pilote sur CD-ROM
Câble USB
Cordon d'alimentation
Un ordinateur avec un port USB 2.0 ou 1.1 de Type A
Disque dur interne SATA I/II, IDE
Lecteur de CD-ROM
Microprocesseur : 300 MHz ou supérieur
Mémoire : 256MB ou supérieur
Windows XP, 2000, ME, 98SE
Remarque : Le disque dur n’est PAS fourni.
Contenu de l'emballage
HD
DATA
USB 2.0 to IDE/SATA Enclosure
(TSE-IS401)
USB Wireless

Français
2
Remarque: Nous vous recommandons de formater tout d'abord un tout
nouveau disque dur. Veuillez consulter la question 2 de la partie dépannage
pour plus d'informations.
Remarque: Veuillez consulter la partie dépannage pour ce qui est des
instructions relatives à l’installation du TSE-IS401 sur Windows 98SE.
1. Enlevez les 4 vis du fond pour
détacher le couvercle.
2. Enlevez les 4 vis pour retirer le
couvercle métallique du disque dur.
2. Installation du matériel
3. Assurez-vous que le cavalier
(jumper) du disque dur est bien
paramétré sur Master.

Français
3
Connexion du lecteur IDE
4. Branchez le câble data
SATA et la prise
d'alimentation sur le
disque dur SATA.
4. Branchez le câble data
IDE et la prise
d'alimentation sur le
disque dur IDE.
Connexion du lecteur
SATA
Câble data IDE
Prise d'alimentation IDE
Prise d'alimentation SATA
Câble data SATA

Français
4
7. Insérez le cordon d'alimentation
dans l'adaptateur AC.
9. Branchez le câble USB fourni à
votre ordinateur et au TSE-IS401.
10. Allumez l'appareil.
6. Remettez le couvecle en position
en le faisant glisser et fixez-le à
l'aide des 4 vis.
5. Mettez le couvercle métallique du
disque dur au dessus du disque
dur et fixez-le à l'aide des 4 vis.
L'installation est maintenant complète.
8. Branchez l'adaptateur secteur
externe au serveur de stockage et
ensuite à une prise de courant.
11. Les pilotes s'installeront
automatiquement.

Français
5
3. Accès aux périphériques de stockage sur
TSE-IS401
Vous pouvez accéder à votre périphérique de stockage
Pour des informations plus détaillées concernant le la configuration et les
paramètres avancés du TSE-IS401, veuillez consulter la section Dépannage, le
CD-ROM contenant le guide de l'utilisateur ou le site Internet de TRENDnet sur
http://www.trendnet.com. Votre configuration est à présent terminée.
1. Double-cliquez sur Poste de
travail et ensuite sur n'importe
quell disque dur installé sous
Network Drives (Disques
réseau).

6
Troubleshooting
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
My computer does not recognize the TSE-IS401. What should I do?
First, verify that the computer meets the minimum requirements as listed in section 1.
Second, make sure that you have plugged in the power into the unit and the power cord into
an outlet. Third, try plugging the device into a different USB port on your computer.
How do I format my brand new hard drive?
For Windows 2000/XP, go to Start -> Settings -> Control Panel -> Administrative
Tools -> Computer Management -> Disk Management. If the Initialize and Convert Disk
Wizard appears, click Cancel. Right click the Unknown drive, click Initialize and then click
OK. Right click on the unallocated region of the hard drive and select New Partition. Follow
the New Partition Wizard instructions then click Finish. The hard drive will automatically
start the formatting process.
For Windows 98SE/ME, right click on My Computer, and then click Device Manager.
Double-click on Disk drives, and then double-click on your hard drive. When the hard drive
properties window appears, click on the Settings Tab. Check Removable in the options
section, select an available drive letter for Start drive letter and then click OK. Click Close.
Click Yes to restart the computer. Double click on My Computer, double-click on the hard
drive and click Yes to format it.
How do I install the TSE-IS401 on Windows 98SE?
1) Insert the Driver CD-ROM into the CD-ROM drive
2) Go to start -> run -> type in D:\Driver\Win98\Setup.exe and click OK. D represents
the drive letter of your CD-ROM drive.
3) Setup successful will appear. Click OK.
4) Follows steps 1-10 in Section 2 to complete the installation.
My computer does not recognize my hard drive(s)? What should I do?
First, verify that the device is installed properly. Right click on My Computer Properties.
Click on Hardware and then Device Manager. Double click on Disk Drives. Make sure
that your hard drive is listed and there is no yellow question mark or exclamation point.
Second, if you are attaching a brand new hard drive, format the drive. Please refer to
question 2 for more information. Third, the hard drive that is connected to the TSE-IS401
must be formatted in FAT-16 or FAT-32 in order for Windows 98SE or ME to recognize it
If you still encounter problems or have any questions regarding the TSE-IS401, please contact
TRENDnet's Technical Support Department.

7
Limited Warranty
- 2-Year Warranty
TRENDnet warrants its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of purchase.
TSE-IS401
If a product does not operate as warranted above during the applicable warranty period,
TRENDnet shall, at its option and expense, repair the defective product or deliver to
customer an equivalent product to replace the defective item. All products that are
replaced will become the property of TRENDnet. Replacement products may be new or
reconditioned.
TRENDnet shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to
service the product through any unauthorized service center. This warranty is voided if
(i) the product has been modified or repaired by any unauthorized service center, (ii) the
product was subject to accident, abuse, or improper use (iii) the product was subject to
conditions more severe than those specified in the manual.
Warranty service may be obtained by contacting TRENDnet office within the applicable
warranty period for a Return Material Authorization (RMA) number, accompanied by a
copy of the dated proof of the purchase. Products returned to TRENDnet must be pre-
authorized by TRENDnet with RMA number marked on the outside of the package, and
sent prepaid, insured and packaged appropriately for safe shipment.

8
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE
AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT
TRENDNET’S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES
NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S
MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED
ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE
RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET
ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER
BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND,
OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND
OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF
LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of
California.
Note: AC/DC Power Adapter, Cooling Fan, Power Supply, and Cables carry a 1-Year
Warranty