TRENDnet TEG-240WS User manual

TEG-160WS
TEG-240WS
C2
Quick Installation Guide

Table of Contents
Version 02.02.2010
English 1
1. Before You Start
2. Hardware Installtion 2
3. Web Management Utility 3
1
Troubleshooting 6

1. Before You Start
Package Contents
?
?CD-ROM (Utility & User’s Guide)
?Multi-Language Quick Installation Guide
?2 Mounting Brackets with Screws
?Power Cord
TEG-160WS/TEG-240WS
System Requirements
1
?Web Browser: Internet Explorer (5.0 or above), Netscape (6.0 or above)
?Computer with Network adapter installed
?Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,
TEG-MGBS80, TEG-MGBS10D35, TEG-MGBS40D35) for Mini-GBIC slots

2. Hardware Installation
2
Note:
1. After hardware installation is complete, use the Web Browser to configure the
TEG-160WS/TEG-240WS. To access the Web Browser configuration, open your web
browser, and enter the default IP Address http://192.168.0.1 and default password
"admin". Make sure your computer and the TEG-160WS/TEG-240WS are configured
to the same network segment.
2. The Mini-GBIC slots are shared with Port 15 and 16 (TEG-160WS) and port 23 and
24 (TEG-240WS) Gigabit Ethernet ports. When the Mini-GBIC slots are in use, port
15 and 16 (TEG-160WS) and port 23 and 24 (TEG-240WS) Gigabit Ethernet ports
are disabled.
2. Connect a CAT-5e or 6 RJ-45 network cable
from the computer to an available Ethernet port
of the TEG-160WS/TEG-240WS.
1. Connect the Power Cord to the rear of the
TEG-160WS/TEG-240WS and then to a power
outlet.

3
2. Follow the Installation Wizard instructions.
Click OK.
1. Insert the Utility & User’s Guide CD-ROM into
your computer's CD-ROM Drive and then click
Install Utility.
3. Web Management Utility
Note: If you would like to easily discover all the Web Management Switches on the
network, assign IP Address, change the password, and upgrade to new firmware, then
install the Web Management Utility. Follow the steps below.
For Windows User
3. Click Start gProgramsg
Web_Management_Utility, and then click
Web_Management_Utility.

4
4. Click Discovery, and then double-click the
Switch that appears in the Discovery List.
5. Click the Switch in the Monitor List and then
click Configuration setting.
7. Click OK.
6. Configure the IP Address, Subnet mask,
Gateway, and Password. Click Set.

5
8. Click Access Web.
9. Type in your Password and then click Login.
By default, the Password is admin.
Your installation is now complete.
For detailed information regarding the Web-based Smart Utility configuration and advanced
settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet

1.
1.
After connecting the TEG-160WS/TEG-240WS to a power outlet, the LEDs do
not turn on.
Check the connection of the power cord to the TEG-160WS/TEG-240WS and the
power outlet. Also check that the power outlet is receiving power.
2. After installing the Web-Management Utility, I clicked Discovery and the Utility
is unable to discover the TEG-160WS/TEG-240WS. What should I do?
Make sure that the TEG-160WS/TEG-240WS is powered on and that all
connections are secure.
2. Also check that your computer's IP Address is on the same network segment as
the TEG-160WS/TEG-240WS. The default IP Address of the
TEG-160WS/TEG-240WS is and the default password is
"admin".
3. When I access the TEG-160WS/TEG-240WS using a web browser, I get a screen
that tells me “only one user can login”. What should I do?
Another computer is configuring the TEG-160WS/TEG-240WS. Please wait until
the user logs off. If the other user has already logged off and you still get the same
screen, then disconnect the power cord from the TEG-160WS/TEG-240WS, wait
for 5 seconds, reconnect the power cord to the TEG-160WS/TEG-240WS, allow 5
seconds for the Switch to power on, and then attempt to access the web
configuration page to login.
4. I forgot the administration password. How do I reset my TEG-160WS/TEG-
240WS?
Press on the reset button using a pen or paperclip for 10 seconds. The default
password is admin.
5.When I connect a computer to the Switch's gigabit port, the LINK/ACT LED turns
on, but the 1000Mbps (TEG-160WS) or the SPEED (TEG-240WS) LED remains off.
1. For the TEG-160WS, when the 1000Mbps LED remains off, the computer's
connection speed is 10Mbps or 100Mbps (if the 100Mbps LED is on).
2. For the TEG-240WS, if the SPEED LED is off, the computer's connection speed is
10Mbps. When the SPEED LED is yellow, the computer's connection speed is
100Mbps. Make sure that you have a Gigabit Ethernet adapter installed. Also
make sure to use a Cat-5e or Cat 6 Ethernet cable.
If you still encounter problems or have any questions regarding the TEG-160WS/TEG-
240WS, please refer to the User's Guide included on the Utility CD-ROM or contact
Trendnet's Technical Support Department.
http://192.168.0.1
Troubleshooting
6

Copyright ©2010. All Rights Reserved. TRENDnet.