TRENDnet TEW-434APB - 54Mbps Wireless G PoE Access... User manual

TEW-434APB
Quick Installation Guide

Table of Contents
Table of Contents
Version 01.08.2007
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
5
8
1. Before You Start
2. Hardware Installation .........................................................................
4. Configure the Access Point ................................................................
.................................................................................
3. Power-over-Ethernet Installation ......................................................

Installation Requirements
Application
Web Browser: Internet Explorer (5.5 or higher)
A computer with a network adapter properly installed
A network Switch or Hub with an available network LAN port
A RJ-45 network cable
Power over Ethernet Switch (Optional)
TPE-101I (Optional)
Package Contents
1. Before You Start
English
1
TEW-434APB
Quick Installation Guide
User’s Guide CD-ROM
AC Power Adapter (7.5V 1A)
1 x 2dBi Detachable Antenna
Note: The TEW-434APB only support Power over Ethernet (PoE) devices that
follow the IEEE 802.3af Mode A (pin 1, 2, 3, 6) standard
Cable/DSL 4-Port Firewall Router
(TW100-BRF114)
Workstation with
PCI Adapter
(TE100-PCIWN)
Cable/DSL
Modem
Internet
Workstation with
Wireless PCI Adapter
(TEW-423PI)
Notebook with
Wireless PC Card
(TEW-421PC)
54Mbps 802.11g Wireless
PoE Access Point
(TEW-434ABP)
Power over Ethernet
(PoE) Injector
(TPE-101i)
PoE + Data
Data
100Mbps

3. Verify that the following front panel
lights are on: WLAN and LAN.
2. Hardware Installation
English
2
2. Connect the Power Adapter to the
Access Point and then to a power
outlet.
Note: Locate an optimum location for the Access Point. The best place for the
Access Point is usually at the center of your wireless network. Please connect
the computer configuring the TEW-434APB to the same switch/hub.
1. Connect a RJ-45 cable from the
Switch/Hub to the LAN port of the
Access Point and then connect the
2dBi Detachable Antenna.

3. Power-over-Ethernet Installation
English
3
Using the TEW-434APB with a PoE switch
2. Verify that the following panel lights
are on: WLAN and LAN. Please
refer to step 3 in the Hardware
Installation section.
1. Connect a RJ-45 cable from the
Power-over-Ethernet Switch (e.g.
TRENDnet TPE-S88) to the LAN
port of the Access Point and then
connect the 2dBi Detachable
Antenna.

English
4
Using the TEW-434APB with the TPE-101I
1. Connect the Power Cord to the
AC Power Adapter.
2. Connect the AC Power Adapter to
the DC 48V IN connector on the
TPE-101I. Then connect the
Power Cord to an outlet.
3. Connect a CAT-5 cable from a
switch to the TPE-101I's DATA IN
port.
4. Connect a CAT-5 cable from the
TEW-434APB's LAN port to the
TPE-101I's POE OUT port
5. Verify that the following panel lights
are on: WLAN and LAN. Please
refer to step 3 in the Hardware
Installation.

English
5
4. Configure the Access Point
Note: It is recommended that you configure the Access Point from a wired
computer. Before the Access Point can be configured, a Static IP address
must be assigned to your computer's network adapter in the subnet of
192.168.1.x. Since the Access Point's default IP address is 192.168.1.100,
make sure no other network devices are assigned an IP address of
192.168.1.100. (Refer to the Troubleshooting section on how to configure
TCP/IP settings on your PC)
2. Enter User name and Password,
and then click OK. By default,
User name: admin
Password: admin
1. Open your web browser, type
http://192.168.1.100 in the
Address bar, and press Enter.
3. Click Wizard.

English
6
5. Enter a new password for your
Access Point, verify the new
password, and then click Next. (If a
new password is not entered, the
default password admin will be
used.
4. Click Next.
6. Enter a SSID for your Access
Point and then click Next.

English
7
8. Click Restart.
7. Enable Encryption if needed and
then click Next.
9. Click Close.
Your installation is now complete.
For detailed information regarding the TEW-434APB's configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.

8
Troubleshooting
Q1: How do I configure TCP/IP settings on my computer?
1. Go into the Control Panel and double-
click the Network Connections icon,
right-click the Local Area Connection
icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and
then click Properties. Then click on
Use the following IP address, and
make sure you assign your network
adapter an IP address in the subnet of
192.168.1.x.
Q2:
A2:
Q3:
A3:
If my network's IP is different than the Access Point's range, what should I
do?
You should still configure the Access Point first. After all the settings are
applied, go to the Access Point's configuration page, click on TCP/IP settings and
change the IP address of the Access Point to match your network's IP.
I typed http://192.168.1.100 in my Internet Browser's Address Bar, but an
error message says “The page cannot be displayed.” How can I get into the
TEW-434APB's web configuration page?
First, check your hardware settings again by following the instructions in
section 2. Second, make sure the LAN and WLAN lights are lit. Third, make sure
the TCP/IP settings are configured properly (see Q1). Fourth, since the Access
Point's default IP address is 192.168.1.100, make sure that no other network
devices are assigned an IP address of 192.168.1.100.

9
Q4:
A4:
Q5:
A5:
Q6:
A6:
After I successfully configured the Access Point to match my network
settings, I can not connect to my network using wireless computers.
If you have a DHCP server in your network, you need to go into TCP/IP
settings again and re-select "Obtain an IP address automatically" to allow the PC
to regain an IP address from your DHCP server.
All the settings are correct, but I can not make a wireless connection to the
Access Point.
First, double check that the WLAN light on the Access Point is lit. Second,
power cycle the Access Point by unplugging the power to the Access Point. Wait
15 seconds, then plug the power back in. Third, contact the manufacturer of your
wireless network adapter. Make sure the wireless network adapter is configured
with the proper SSID. The default SSID of the Access Point is TRENDnet.
The TEW-434APB does not power on when I plug the device into a Power-
Over-Ethernet switch or splitter. What should I do?
First, verify that the PoE device supports IEEE 802.3af protocol. Second,
verify that the TEW-434APB powers up using the provided 7.5V, 1A power
adapter. Third, power cycle the PoE switch. Fourth, unplug power to the switch,
wait 15 seconds, then plug the power back in. Fifth, plug the device into a
different port on the PoE switch. Sixth, try using another Cat-5e cable.
If you still encounter problems or have any questions regarding the TEW-434APB,
please contact TRENDnet's Technical Support Department.

Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.

Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com
TRENDnet Technical Support
US Canada
24/7 Tech Support
Toll Free Telephone: [phone]
Europe (Germany France Italy Spain Switzerland UK)
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
Toll Free Telephone: [phone]
.
. . . . .
Copyright ©2007. All Rights Reserved. TRENDnet.
20675 Manhattan Place
Torrance, CA 90501
USA