TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... User manual

TEW-455APBO
Quick Installation Guide

Table of Contents
Table of Contents
Version 09.18.2007
English ........................................................................................... ........................ 1
1
3
6
9
10
13
1. Before You Start
2. Hardware Installation ......................................................... ...............
....................................................................... .....................
.............
3. Mounting ........................................................................................................
4. Connecting TRENDnet External Antenna ......................................................
5. Configure the Access Point ...........................................................................
Troubleshooting .....................................................................................................

System Requirements
Package Contents
1. Before You Start
English
1
?
?
?
?
?
?
?
?
T
User’s Guide CD-ROM
Quick Installation Guide
AC Power Adapter (48V DC)
Power Cord
Mounting Kit
Waterproof Kit
Grounding wire
EW-455APBO
?
?A computer with a network adapter properly installed
?A network Switch or Hub with an available network LAN port
?2 x RJ-45 network cable
?RJ-45 Crimper
?Wire stripper
?Screwdriver
?External Antenna with N-type Female connector (Optional)
?TEW-ASAL1 (Optional)
Web Browser: Internet Explorer (5.5 or higher)
Note: The TEW-455APBO does not support IEEE 802.3af. You must use the
special Power over Ethernet adapter that is supplied with the TEW-455APBO.

Application
English
2
9dBi High Power Wireless
Outdoor PoE Access Point
(TEW-455APBO)
Cable
(TEW-ASAL1)
Cable/DSL
Modem
Cable/DSL Advanced
VPN Firewall Router
(TW100-BRV304)
Workstations with
PCI Adapter
14 dBi Outdoor High-Gain
Directional Antenna
(TEW-OA14D)
16-Port 10/100Mbps
Fast Ethernet Switch
(TE100-S16R)
Internet
10/100Mbps
Multi-Port Print Server
(TE100-P21)
Printers
Workstations with
PCI Adapter
Notebook with
PC Card
PoE Power Adapter
PoE Power Adapter

2. Hardware Installation
Note: Please connect the computer configuring the TEW-455APBO to the
same switch/hub.
3. Connect the green grounding wire
to a grounding object.
e.g. Earth Driven rod, Grounded
Electrical System, Building Frame.
4. Use a wire stripper to strip off
about 2 inches of the cable sheath
from one end of an Ethernet cable.
5. Insert the seal into the rear of the
clamp ring. Then insert the gasket
into the front end of the clamp ring.
6. Insert the body, the screw nut, the
sealing nut and clamp ring into the
stripped end of the cable.
English
3
1. Remove the screw and washer
from the grounding hole using a
screwdriver.
2. Align one end of the grounding
wire over the hole. Then connect
the screw and washer back in.

7. Insert the wires on the stripped end
of the cable into the RJ-45 plug.
Make sure the wires are inserted
into the RJ-45 plug based TIA/EIA
T-568A or T-568B standard.
8. Crimp the stripped cable to the
RJ-45 plug.
9. Insert the gasket to the front end of
the connector. Then put the screw
nut on the back.
10. Connect the clamp ring and
seating nut to the PoE port on the
rear of the TEW-455APBO.
English
4

13. Connect the opposite end of the
Ethernet cable to a LAN port on
your network.
English
5
11. Connect the opposite end of the
Ethernet cable to the LAN + DC
port on the Power over Ethernet
Adapter.
12. Connect one end of another
Ethernet cable to the LAN port.
14. Connect the power cord into the
power over Ethernet adapter.
Then connect the power cord into
a power outlet.
15. Verify that the following panel
lights are on: Power and WLAN.

3. Mounting
Wall Mounting
2. Use the wall bracket as a template
and mark the wall for the correct
screw / fastener position.
1. Align the mounting bracket with the
holes on the bottom of the unit and
secure it with the screws and
washers provided.
4. Insert fastener plugs into the drilled
holes.
3. Drill holes for the fastener plugs at
the marked positions on the wall.
5. Use the provided wood screws to
screw the outdoor unit/swivel
mounting bracket to the fastener
plugs to the wall.
English
6

8. Once the unit is positioned
correctly, tighten all screws.
7. Adjust the orientation of the
antenna as necessary.
Pole Mounting
1. Align the mounting bracket with the
holes on the bottom of the unit and
secure it with the screws and
washers provided.
2. Slide the two provided u-clamps
around the pole. Place the pole
mounting bracket at the desire
height and position.
English
7
6. Insert the mounting bracket into the
wall mounting bracket and secure
with the washers and screws
provided.

English
8
3. Secure the mounting bracket to the
pole mounting bracket using the
nuts and washers provided.
4. Adjust the orientation of the
antenna as necessary.