TRENDnet TEW-821DAP User manual

TEW-821DAP (V1)
Quick Installation Guide

Table of Content
1 English
1. Before You Start
2. Initial Access Point Setup
3. AP Management Utility
4. Mounting the Device

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
1
1. Before You Start
Package Contents
ŸTEW-821DAP
Ÿ 1 x 5 ft. (1.5 m) network cable
ŸCD-ROM (User's Guide and Utility)
ŸQuick Installation Guide
ŸPower adapter (12V DC, 1A)
ŸMounting Plate
Minimum Requirements
ŸComputer with network port and web browser
Ÿ Network switch or router with an available network port
Mac Users: Please refer to the User's Guide to manually configure the access point.

2
1. Bring the TEW-821DAP to a location of its final installation point.
3. If you are connecting your TEW-821DAP to a PoE switch, the device will power on
automatically. If you are connecting to a computer, or a non-PoE switch, you will need to use
the included power adapter.
4. To use the power adapter, plug the power adapter into the TEW-821DAP, then plug the
adapter into an electrical outlet. Wait 60 seconds, then confirm that the status LEDs on the
front of the unit are illuminated. Your TEW-821DAP access point is now active. The device is
pre-configured to automatically connect to your network.
2. Initial Access Point Setup
2. Connect the TEW-821DAP to your router or switch. You may also connect the device directly
to a network port on your computer. If you are connecting to a router or switch, make sure
your computer is connected to the same network.
5. For your security, each TEW-821DAP comes pre-encrypted with a unique WiFi Name (SSID)
and WiFi Password. You can find your device's SSID and WiFi password on the white labels
located on the device. Use this information to connect to the TEW-821DAP access point. If
the TEW-821DAP is reset, the SSID and WiFi key will also be reset to the default login
credentials located on the white label.
6. No further setup is required, proceed to Section 4 Mounting the Device. To change device
settings proceed to Section 3 AP Management Utility.
Preset
Wireless Settings
Wi-Fi Name/SSID
(AC/N)
TRENDnetXXX_5GHz_XXXX
(N/B/G)
TRENDnetXXX_2.4GHz_XXXX
Wi-Fi Password
Management Login
http://tew-821dap
username: admin
password: admin
XXXXXXXXXXXXX

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
3
2. Run the utility. The utility will attempt to detect your device automatically. If it does not, click
on the Discover button.
Note: The AP Utility only supports Windows based computers. Please visit TRENDnet.com for
complete list of the AP Utility’s supported operating systems.
3. AP Management Utility
1. Insert the included CD into your computer, and select AP Utility from the menu.

4
3. Select your device by checking the box next to your TEW-821DAP, and click on Device
Settings.
4. The Device Settings page will show your basic Wi-Fi network settings. If your network
requires a static IP address, select the Static radio button and enter your settings. If you are
not sure, leave IP Mode on the default setting, DHCP.
Static
Static

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
5
7. If you are using both 2.4GHz and 5GHz networks, they must be configured individually.
Repeat steps 2 to 6 to configure your other network
5. To configure your wireless network, select the Band from the dropdown menu, and enter your
settings. If you are using both 2.4GHz and 5GHz networks, they must be configured
individually. The Key is your current WiFi password. The default key is located on the white
sticker on the bottom of the TEW-821DAP.
6. When you are finished, enter the password for your TEW-821DAP (NOT your WiFi password)
and click OK to save your changes. If this is the first time you are accessing the device, or if the
unit has been reset, the default password is admin. The utility will save your settings.
8. Once your wireless networks are configured, confirm connectivity by logging into your
TEW-821DAP WiFi network. If you can successfully connect, your configuration is complete.
Preset
Wireless Settings
Wi-Fi Name/SSID
(AC/N)
TRENDnetXXX_5GHz_XXXX
(N/B/G)
TRENDnetXXX_2.4GHz_XXXX
Wi-Fi Password
Management Login
http://tew-821dap
username: admin
password: admin
XXXXXXXXXXXXX
Band

6
12. Select the desired language, then click Login to continue.
9. To access the unit's advanced settings, launch the AP Utility, locate your TEW-821DAP, click
on the IP Address, and select Yes to configure your device.
192.168.10.62
11. On the Login screen, enter the username and password. If this is your first time accessing
the device, or if the TEW-821DAP has been reset, the default login credentials are:
Name: admin
Password: admin
10. This will launch your default web browser, and automatically direct it to your TEW-821DAP
for advanced settings.

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
7
13. The status screen will display information about your TEW-821DAP access point, and the
unit's wireless networks.
14. For detailed information on advanced settings and features, please refer to the User's
Guide.

8
4. Mounting the Device
1. Remove the mounting plate from the TEW-821DAP.
2. Place the mounting plate on the wall or ceiling where the device will be located, and mark
the location of the screw holes. Ensure that the device has enough clearance to slide on and
off the mounting plate. If you are using a non-PoE router or switch, and external power is
required, ensure that your mounting location has access to an electrical outlet.
3. Drill out the marked screw holes, and insert the plastic wall anchors into the screw holes.
4. Secure the mounting plate, using the screws that came with the device.
5. Place the TEW-821DAP on the mounting plate, and attach the network cable. If you are using
a non-PoE router or switch and require external power, connect the power adapter.
Toll Free English Technical Support
US/Canada: 855-373-4741
Hours: Monday-Friday
7:00 AM- 6:00 PM, Pacific Standard Time.
After hours: 866-845-3673
25
4
3

Directives: Low Voltage Directive 2014/35/EC
EMC Directive 2014/30/EC
R&TTE Directive 1999/5/EC
EMF Directive 1999/519/EC
Ecodesign Directive 2009/125/EC
RoHS Directive 2011/65/EU
REACH Regulation (EC) No. 1907/2006
TRENDnet hereby declare that the product is in compliance with the essential requirements and
other relevant provisions under our sole responsibility.
This product is herewith confirmed to comply with the Directives.
Product Information
Product Name:
Model Number: TEW-821DAP
Trade Name: TRENDnet
EN 300 328 V1.9.1: 02-2015
EN 301 893 V1.8.1: 03-2015
EN 62311: 2008
N300 PoE Access Point
Safety EN 60950-1: 2006 + A11: 2009: + A1: 2010 + A12: 2011 + A2: 2013
EMC
Regulation (EC) No. 1275/2008, No. 278/2009, No. 801/2013
Energy Efficiency
EN 301 489-1 V1.9.2: 09-2011
EN 301 489-17 V2.2.1: 09-2012
EN 55032: 2012/AC:2013, Class B
EN 55024: 2010
Manufacturer’s Name and Address
Radio Spectrum & Health
Person responsible for this declaration.
Signature:
Date: March 27, 2017
Title: Director of Technology
Name: Sonny Su
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Zwolsestraat 156 2587 WB
The Hague The Netherlands
Place of Issue: Torrance, California, USA

Certifications
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
TRENDnet
20675 Manhattan Place
Torrance, CA 90501
USA
Applies to PoE Products Only: This product is to be connected
only to PoE networks without routing to the outside plant.
Note
The Manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority
to operate the equipment.
Advertencia
En todos nuestros equipos se mencionan claramente las
caracteristicas del adaptador de alimentacón necesario para
su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo
conectado. El adaptador de alimentación debe operar con
voltaje y frecuencia de la energia electrica domiciliaria exitente
en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your
product online. Go to TRENDnet’s website at:
www.trendnet.com/register
Technical Support
If you have any questions regarding the product
installation, please contact our Technical Support.
Toll free US/Canada: 1-855-373-4741
Regional phone numbers available
at www.trendnet.com/support
Waste electrical an electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or Retailer for recycling advice.
Copyright © 2017. All Rights Reserved. TRENDnet. TEW-821DAP (V1) / 03.27.2017