Tripp Lite PDU10K User manual

Owner’s Manual
PDU10K Power Distribution Unit (PDU)
for select UPS Systems
Designed for 2U rack and other mounting options
Congratulations! Your power distribution unit will add a wide range of electrical outlets to select Tripp Lite
SmartOnlineTM UPS Systems and SmartPro®UPS Systems.
A variety of installation options are available: 2U
rackmount, wall mount, under-console mount and
more.
Note: The user must supply and determine the
fitness of all hardware (including rackmount
screws, bolts and cage nuts) required in the
installation process; the user must also determine
the fitness of the mounting surface.
On each side of the unit, run four rackmount
screws through star washers, through one of the
mounting clips and into the unit's pre-drilled holes.
The mounting clips can be oriented in a variety
of ways to suit a variety of applications. A recessed
rackmount installation allows space for connected
cables in front of the rack or enclosure.
B
A
Installation
A
IMPORTANT SAFETY INSTRUCTIONS. This manual contains information
concerning the proper installation and use of Tripp Lite’s Power Distribution
Units (PDUs). SAVE THESE INSTRUCTIONS.
Note: This PDU is intended only for use with select Tripp Lite UPS Systems.
The PDU's input must be grounded. Do not use it with extension cords or adapters that
eliminate its connection to ground. Your PDU is designed for indoor use only. Install it
away from heat emitting devices such as radiators and heat registers. Do not install where
excessive moisture or other conductive contaminants are present. Never install electrical
wiring during a lightning storm.
B
Standard PDU Shown
(Outlet Configuration Varies Depending on Model)
200402057 PDU10K Owner’s Manual.qxd 2/12/2004 4:29 PM Page 1

Specifications
Model: PDU10K
Series Number: AGAC4996
Nominal Voltage/Frequency: 120/240V; 50/60Hz
Maximum Load Rating (amps): 30 A
AC Receptacles: (2) L6-30R, (2) L6-20R, (1) L5-30R, (2) 5-15/20R
AC Input: Hardwire
Circuit Breakers (Resettable double pole): 1 x 20 A; 1 × 30 A
Dimensions (H×W×D, inches): 3.5 × 17.25 × 3.5
Input Connection
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and
workmanship for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or
replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product
(with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609. Seller will pay return shipping
charges. Call Tripp Lite at [phone] before sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR
NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN.
EXCEPT TO THE EXTEND PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL
WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH
ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states
do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights,
and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe
for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation
or warranty as to the suitability or fitness of these devices for any specific application.
Policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
Limited Lifetime Warranty
Features
Circuit Breakers
Your PDU features two double-pole output circuit breakers (20-amp and 30-amp). If the
current draw on the receptacles exceeds the amperage rating of its circuit breaker, the circuit
breaker will trip to prevent any possible damage. Remove excess draw and reset breaker.
Grounding Lug
Use this screw (located on the rear of the unit) to connect your PDU to ground.
200402057 93-2221
Access the PDU's hardwire input terminal box by removing the top
panel. Observe labeling on the terminals which indicate ground, neutral,
hot1 and hot2. Although only four terminals require wiring, your model
may or may not have two additional terminals, as shown in the diagram,
which have no function.
C
WARNING!
Hardwire input connection must be performed by a qualified electrician
observing appropriate local and national regulations, including the National
Electrical Code (NEC).
C
Standard PDU Shown
(Number of Terminals Varies
Depending on Model)
200402057 PDU10K Owner’s Manual.qxd 2/12/2004 4:29 PM Page 2