Tripp Lite PDUMNH20HV User manual

Owner’s Manual
1
High Voltage
Monitored Rack PDUs
Model: PDUMNH20HV
(Series Number: AGPD7989)
1. Important Safety Instructions 2
2. Features 3
3. Installation 5
3.1 Mounting the PDU 5
3.2 Connecting the PDU 7
3.3 Networking the PDU 9
3.4 Testing Network Connection 9
3.5 Remote Monitoring and Control 10
4. Technical Support 10
5. Warranty and Product Registration 11
Español 12
Français 23
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All rights reserved.
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $50 value!
www.tripplite.com/warranty
15-04-184-93341C.indb 1 4/16/2015 8:49:09 AM

2
1. Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be
followed during the installation, operation, and storage of this
product. Failure to heed these instructions may affect your
warranty.
• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge
or line noise protection for connected equipment.
• The PDU is designed for indoor use only, in a controlled environment, away from
excess moisture, temperature extremes, conductive contaminants, dust or direct
sunlight.
• Keep indoor ambient temperature between 0°C and 40°C.
• The PDU must be installed by a qualified technician only.
• Do not attempt to mount the PDU to an insecure or unstable surface.
• Install in accordance with National Electrical Code standards. Be sure to use the
proper overcurrent protection for the installation, in accordance with the plug/
equipment rating.
• Connect the PDU to an outlet that is in accordance with your local building codes and
that is adequately protected against excess currents, short circuits and earth faults.
• The electrical outlets supplying power to the equipment should be installed near the
equipment and easily accessible.
• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters
that eliminate the connection to ground.
• Be sure to provide a local disconnect device on any models that are permanently
installed without a plug that is easily accessible.
• Never attempt to install electrical equipment during a thunderstorm.
• Individual equipment connected to the PDU should not draw more current than the
individual PDU’s outlet’s rating.
• The total load connected to the PDU must not exceed the maximum load rating for
the PDU.
• Do not attempt to modify the PDU, input plugs or power cables.
• Do not drill into or attempt to open any part of the PDU housing. There are no user-
serviceable parts inside.
• Do not attempt to use the PDU if any part of it becomes damaged.
• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended. Do not use this
equipment in the presence of a flammable anesthetic mixture with air, oxygen or
nitrous oxide.
15-04-184-93341C.indb 2 4/16/2015 8:49:09 AM

LOAD (AMPS)
A B
3
2. Features
AC Input Power Cord: The detachable cord has an IEC-
320-C19 connector Aand an IEC-320-C20 connector B.
IEC-320-C20 Power Inlet: The IEC power inlet connects to
the included power cord or a compatible user-supplied power
cord.
AC Input Adapter: The adapter converts the AC input power
cord to a NEMA L6-20P plug. The included retention bracket
(not shown) secures the connection.
IEC-320-C13 Output Receptacles: These receptacles
distribute 208/230V AC power to connected equipment.
Digital Load Meter (Ammeter): The digital load meter
displays the load in amps.
Longer 1U Mounting Brackets: Use these brackets to
mount the 1U PDU horizontally in a standard rack or rack
enclosure. The mounting depth can be adjusted by attaching
the brackets to different positions on the PDU.
Shorter 0U Mounting Brackets: Use these brackets
to mount the PDU in a 0U rack, wall or under-counter
configuration for 1U PDU models.
Accessory Slot: An SNMP card has been installed in the
slot, allowing the PDU to be monitored remotely.
Factory Port: The port is reserved for configuration by factory
authorized personnel only. Do not connect anything to the
port.
15-04-184-93341C.indb 3 4/16/2015 8:49:09 AM

AB
C
4
2. Features
SNMP Card Ports:
PS/2 Port: Use this port to connect a Tripp Lite
ENVIROSENSE environmental sensor to provide remote
temperature/humidity monitoring and a dry contact interface
to control and monitor alarm, security and telecom devices.
Visit www.tripplite.com for ordering information.
Note: Do not connect a keyboard or mouse to this port.
Mini-DIN Serial Port: Use this port to provide a direct
terminal connection to a computer with a terminal emulation
program. A serial cable (part number 73-1025) is included
with the PDU. If you need to order a replacement cable, visit
www.tripplite.com.
Ethernet Port: Use this RJ-45 jack to connect the PDU to
the network with a standard Ethernet patch cable. The
Status LED Aand Link LED Bindicate several operating
conditions, as shown in the table below. This port is not
compatible with PoE (Power Over Ethernet) applications.
Network Operating Conditions
AStatus LED Color
Off Card Not Initialized
Steady Green Card Initialized and Operational
Flashing Amber Error - Card Not Initialized
BLink LED Color
Off No Network Connection
Flashing Amber 100 Mbps Network Connection
Flashing Green 10 Mbps Network Connection
SNMP Reset Button: The SNMP reset button Cis recessed
in a small opening between the Link and Status LEDs. To
reset your SNMPWEBCARD, use a small tool to press the
reset button for 3 seconds. Rebooting the network card will
not erase network settings or interrupt AC power.
15-04-184-93341C.indb 4 4/16/2015 8:49:09 AM

3.1-1
3.1-1
3.1-2
3.1-2
5
3. Installation
3.1 Mounting the PDU
The PDU supports five primary mounting configurations: 1U Rack, 0U Rack, Wall,
Under-Counter and Reduced-Depth.
Note: Regardless of configuration, the user must determine the fitness of hardware and
procedures before mounting. The PDU and included hardware are designed for common rack
and rack enclosure types and may not be appropriate for all applications. Exact mounting
configurations may vary.
3.1-1 1U Rack Mounting: Use three
screws to attach each of the two
longer mounting brackets to the
PDU as shown. You can mount
the PDU in a recessed position by
attaching the mounting brackets so
they extend beyond the front panel
of the PDU. Mount the PDU in the
rack by inserting four user-supplied
screws through the mounting
brackets and into the mounting
rack rails.
3.1-2 0U Rack Mounting: Use three
screws to attach each of the two
shorter mounting brackets to the
PDU as shown. Mount the PDU
vertically by inserting two or more
user-supplied screws through
the mounting brackets and into
mounting points in the rack or rack
enclosure.
You may have to remove the
screws attaching the mounting
brackets to the PDU, change the
orientation of the brackets as
shown and reattach the brackets.
Use only the screws supplied by
the manufacturer or their exact
equivalent (#8-32, 3/16” flat
head). Attach the PDU vertically by
inserting two or more user-supplied
screws through the PDU mounting
brackets and into mounting points
in the rack or rack enclosure.
15-04-184-93341C.indb 5 4/16/2015 8:49:10 AM

3.1-3
3.1-3
WALL
3.1-4
3.1-4
6
3. Installation
3.1-3 Wall Mounting: Use three screws
to attach each of the two shorter
mounting brackets to the PDU
as shown. Mount the PDU to
the wall by inserting two or more
user-supplied screws through the
mounting brackets and into secure
mounting points.
You may have to remove the
screws attaching the mounting
brackets to the PDU, change the
orientation of the brackets as
shown and reattach the brackets.
Use only the screws supplied by
the manufacturer or their exact
equivalent (#8-32, 3/16” flat
head). Attach the PDU to a stable
mounting surface by inserting
two or more user-supplied screws
through the PDU mounting
brackets and into secure points on
the mounting surface.
3.1-4 Under-Counter Mounting: Use
three screws to attach each of
the two shorter mounting brackets
to the PDU as shown. Mount the
PDU under the counter by inserting
two or more user-supplied screws
through the mounting brackets and
into secure mounting points.
You may have to remove the
screws attaching the mounting
brackets to the PDU, change the
orientation of the brackets as
shown and reattach the brackets.
Use only the screws supplied by
the manufacturer or their exact
equivalent (#8-32, 3/16” flat
head). Attach the PDU to a stable
mounting surface by inserting
two or more user-supplied screws
through the PDU mounting
brackets and into secure points on
the mounting surface.
15-04-184-93341C.indb 6 4/16/2015 8:49:10 AM

3.1-5
3.1-5
A
DC
B
3.2-1
7
3. Installation
3.1-5 Reduced-Depth Mounting: Use
three screws to attach each of the
two shorter mounting brackets to
the PDU as shown. Mount the PDU
to a stable surface with the outlets
facing upward by inserting two or
more user-supplied screws through
the mounting brackets and into
secure mounting points.
3.2 Connecting the PDU
3.2-1 Input Power Cord Connection:
Attach the cable clamp to the PDU
by inserting the tabs into available
slots on the top and bottom of the
power inlet A. Secure the clamp
by sliding it to the right. Attach the
included power cord to the PDU by
inserting the IEC C19 connector B
of the power cord into the cable
clamp and IEC C20 power inlet C.
Install the included screw Don
the cable clamp to secure the
power cord connection. Connect
the other end of the input power
cord to a compatible source of AC
power, such as a UPS system, PDU
or utility outlet.
Note: The AC power source should not
share a circuit with a heavy electrical
load.
Note: When connecting the PDU, it
should be provided with over-current
protection and a maximum 20A
branch-rated over-current protection
device.
15-04-184-93341C.indb 7 4/16/2015 8:49:10 AM

A
B
C
3.2-2 C
88
C
A
B
3.2-4
3.2-3
8
3. Installation
3.2-3 NEMA Power Cord Connection:
Insert the IEC C19 connector Aof
the input power cord into the IEC
C20 inlet Bof the PDU. Connect
the other end of the input power
cord Cto a compatible source of
AC power, such as a UPS system,
PDU or utility outlet. The PDU
should be provided with over-
current protection. The PDU should
be provided with a maximum 20A
branch-rated over-current
protection device.
Note: The AC power source should not
share a circuit with a heavy electrical
load (such as an air conditioner or
refrigerator).
3.2-2 NEMA Adapter Connection: The
PDU includes a plug adapter that
adds a NEMA L6-20P plug to the
input power cord. Use this adapter
only if you will be connecting the
PDU to a NEMA L6-20R outlet.
Insert the IEC C19 connector Aof
the adapter into the IEC C20
connector Bof the input power
cord. Secure the connection with
the retention bracket Cby using
the included bolts to fasten the two
halves of the bracket around the
connection as shown.
Caution: To avoid the risk of
electric shock, ensure that the
Neutral (L2) conductor has been
identified before connecting the
PDU.
3.2-4 Connect Equipment to PDU: Do
not exceed the load rating of the
PDU. The total electrical current
used by the PDU will be displayed
on the digital meter in amperes.
Refer to the Digital Load Meter
(Ammeter) in the Features section
for more information.
15-04-184-93341C.indb 8 4/16/2015 8:49:11 AM

A
B
A
9
3. Installation
3.3 Networking the PDU
Connect PDU to Network: While the
PDU is powered, connect a standard
Ethernet patch cable to the RJ-45
Ethernet port Aon the PDU.
Note: This port is not compatible with PoE
(Power over Ethernet) applications.
3.4 Testing Network Connection
Access PDU with Web Browser: After an
IP address has been assigned to the PDU,
attempt to access it with a Web browser
that supports frames, forms and Java™.
Open a Web browser on a computer
connected to the LAN and enter the IP
address assigned to the PDU. You should
be prompted for a password A. The user
name is localadmin and the default
password is localadmin. After you enter
the user name and password, the
PowerAlert Status page Bwill appear in
the browser window. For more information
about configuration and operation of the
PDU via the PowerAlert interface, refer to
the SNMPWEBCARD Installation Guide.
Note for Network Management System
Users Only: Two MIB files - Tripplite.mib
and RFC1628.mib - must be loaded on
each Network Management Station that will
monitor the PDU via SNMP. The files can be
downloaded from the Support section of your
PDU product’s webpage at www.tripplite.com.
A
3.2-5
3.2-5 Optional Cord Retention
Procedure: Use the included C14
plastic sleeves to secure plugs to
receptacles. Attach the sleeve to
the plug, making sure that the pull
tabs Aremain outside the plug
and that the fit is secure. To unplug
equipment properly, use the pull
tabs to remove the plug and sleeve
from the receptacle.
The PDU will attempt to obtain an IP address via DHCP. This may take as long as
several minutes, depending on your network environment. For more information
about configuration and operation of the PDU via the PowerAlert interface, refer to the
SNMPWEBCARD User’s Guide provided in the Support section of your PDU product’s
webpage at www.tripplite.com.
15-04-184-93341C.indb 9 4/16/2015 8:49:12 AM

A
B
10
4. Technical Support
Web: www.tripplite.com/support Email: [email protected]
3. Installation
3.5 Remote Monitoring and Control
The PDU provides remote monitoring A,
outlet control Band more via Web
browser, telnet and SNMP-based Network
Management Systems. For more
information about configuration and
operation of the PDU via the PowerAlert
Web browser interface, refer to the
SNMPWEBCARD Installation Guide. You
can find the guide by going to
www.tripplite.com/support and typing
“SNMPWEBCARD” in the search field.
15-04-184-93341C.indb 10 4/16/2015 8:49:12 AM