Tripp Lite PDU3VSR6H50A User manual

1
Owner’s Manual
3-Phase Switched 0U Power
Distribution Units
208V MODELS
PDU3VSR6H50A • PDU3VSR6G60A
(Series Number: AG-0065) • (Series Number: AG-0063)
400V MODELS
PDU3XVSRHWA • PDU3XVSRHWB PDU3XVSR6G32A • PDU3XVSR6G32B
(Series Number: AG-0057) (Series Number: AG-0080)
PDU3XVSR6L2230 • PDU3XVSR6L2230B PDU3XVSR6G60A • PDU3XVSR6G60B
(Series Number: AG-0056) (Series Number: AG-0093)
PDU3XVSR6G30A • PDU3XVSR6G30B PDU3XVSR6G63A • PDU3XVSR6G63B
(Series Number: AG-0096) (Series Number: AG-0094)
Important Safety Instructions 2
Installation 3
Digital Display 8
Using the Digital Display 10
Features 16
Configuration and Operation 18
Service 18
Warranty and Warranty Registration 19
Español 20
Français 39
Русский 58
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an ISOBAR6ULTRA
surge protector—a $100 value!
www.tripplite.com/warranty
18-12-188-9332B8.indb 1 12/20/2018 5:19:13 PM

2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during
the installation, operation, and storage of this product. Failure to heed these
instructions and warnings may affect the product warranty.
• The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise
protection for connected equipment.
• The PDU is designed for indoor use only in a controlled environment away from excess
moisture, temperature extremes, conductive contaminants, dust or direct sunlight.
• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that
eliminate the connection to ground.
• The power requirement for each piece of equipment connected to the PDU must not exceed
the individual outlet’s load rating.
• The total power requirement for equipment connected to the PDU must not exceed the
maximum load rating for the PDU.
• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable
parts inside.
• Do not attempt to modify the PDU, including the input plugs and power cables.
• Do not attempt to use the PDU if any part of it becomes damaged.
• Do not attempt to mount the PDU to an insecure or unstable surface.
• Use of this equipment in life support applications where failure of this equipment can
reasonably be expected to cause the failure of the life support equipment or to significantly
affect its safety or effectiveness is not recommended. Do not use this equipment in the
presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
• Never attempt to install electrical equipment during a thunderstorm.
• Keep indoor ambient temperature between 32°F and 104°F (0°C and 40°C).
• Connect the PDU to an outlet that is in accordance with your local building codes and that is
adequately protected against excess currents, short circuits and earth faults.
• Do not attempt to open the PDU; there are no user-serviceable parts inside.
• The PDU must be installed by a qualified technician only.
18-12-188-9332B8.indb 2 12/20/2018 5:19:13 PM

1-1 1-2
1-4
1-3
1-5
A
B
3
Installation
Mounting the PDU
Note: The illustrations may differ somewhat from your PDU model. Regardless of configuration, the user must
determine the fitness of hardware and procedures before mounting. The PDU and included hardware are designed
for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting
configurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws
supplied by the manufacturer or their exact equivalent.
Note: Mounting buttons come preinstalled to the PDU for toolless mounting.
1-1 To attach the mounting brackets to the
PDU, remove the mounting buttons.
1-2 Attach the mounting brackets to the
PDU with the included screws.
1-3 Attach the PDU to a vertical rail in
your rack or rack enclosure. (Use the
mounting hardware that came with your
rack or rack enclosure to attach the
mounting brackets to the rail.)
1-4 To reinstall the mounting buttons for
toolless mounting, remove the mounting
brackets then install the mounting
buttons onto the PDU. Position the PDU
as desired in the rack enclosure, align
the buttons with the rack mounting
slots, and slide the PDU into position.
Note: Be sure to insert the 2 buttons into either
the upper hole at each end of the PDU or into
the lower hole at each end of the PDU.
1-5 To install the PDU with its outlets facing
the rear of the rack, use the included
PDUMVROTATEBRKT accessory. First,
attach the mounting button Ato the
V-shaped bracket Busing the included
screw and washer. Then, use the
button-mount slot to attach the bracket
to the PDU and the mounting button to
attach the PDU to the rack. The bracket
effectively repositions the mounting
brackets allowing for the PDU outlets to
face the rear of the rack.
18-12-188-9332B8.indb 3 12/20/2018 5:19:14 PM

4
Installation
Connecting the PDU
2-1 Each 208V model is equipped with 1 of 2 different input plugs.
60A Blue IEC
309 3P+E
Model Name Input Plug
Max Input
Amps (Limited
by Input Cord
and Plug)
Input
Voltage
Output
Voltage Breakers
Cord
Length
Outlets
PDU3VSR6G60A 60A Blue IEC
309 3P+E 45A 208V 208V 6 x Double
Pole, 20A
Branch-Rated
6 ft.
(1.8 m) 18 Total; 6 Banks of (2) C19 and (1) C13
PDU3VSR6H50A HUBBLE
CS8365C 40A 208V 208V 6 x Double
Pole, 20A
Branch-Rated
6 ft.
(1.8 m) 18 Total; 6 Banks of (2) C19 and (1) C13
HUBBLE
CS8365C
18-12-188-9332B8.indb 4 12/20/2018 5:19:14 PM

5
Installation
Each 400V model is equipped with 1 of 3 different input plugs.
63A Red IEC 309
3P+N+E
L22-30P 32A Red IEC 309
3P+N+E
Model Name Input Plug
Max Input
Amps (Limited
by Input Cord
and Plug)
Input
Voltage
Output
Voltage Breakers
Cord
Length
Outlets
PDU3XVSR6L2230
L22-30P 24A 400V 230V
6 x Single
Pole, 20A
Branch-
Rated
6 ft.
(1.8 m)
24 Total; 6 Banks of
(2) C19 and (2) C13
PDU3XVSR6L2230B 30 Total; 6 Banks of
(1) C19 and (4) C13
PDU3XVSR6G30A 30/32A Red
IEC 309
3P+N+E 24A 400V 230V
6 x Single
Pole, 20A
Branch-
Rated
6 ft.
(1.8 m)
24 Total; 6 Banks of
(2) C19 and (2) C13
PDU3XVSR6G30B 30 Total; 6 Banks of
(1) C19 and (4) C13
PDU3XVSR6G32A 30/32A Red
IEC 309
3P+N+E 32A 400V 230V
6 x Single
Pole, 20A
Branch-
Rated
6 ft.
(1.8 m)
24 Total; 6 Banks of
(2) C19 and (2) C13
PDU3XVSR6G32B 30 Total; 6 Banks of
(1) C19 and (4) C13
PDU3XVSR6G60A 60/63A Red
IEC 309
3P+N+E 35A 400V 230V
6 x Single
Pole, 20A
Branch-
Rated
6 ft.
(1.8 m)
24 Total; 6 Banks of
(2) C19 and (2) C13
PDU3XVSR6G60B 30 Total; 6 Banks of
(1) C19 and (4) C13
PDU3XVSR6G63A 60/63A Red
IEC 309
3P+N+E 40A 400V 230V
6 x Single
Pole, 20A
Branch-
Rated
6 ft.
(1.8 m)
24 Total; 6 Banks of
(2) C19 and (2) C13
PDU3XVSR6G63B 30 Total; 6 Banks of
(1) C19 and (4) C13
PDU3XVSRHWA
N/A 40A 400V 230V
6 x Single
Pole, 20A
Branch-
Rated
N/A
24 Total; 6 Banks of
(2) C19 and (2) C13
PDU3XVSRHWB 30 Total; 6 Banks of
(1) C19 and (4) C13
18-12-188-9332B8.indb 5 12/20/2018 5:19:14 PM

6
5
4LOAD L2
BANK 1
3
1211
10
B4
B3
9
87
LOAD L1
BANK 2
LOAD L3
BANK 1
LOAD L2
BANK 1
STATUS
LINK
RESET
ENVIROSENSE
CONFIG
2-2
2-3
2-4
B
2-5
A
A B
6
Installation
2-2 Connect the input plug to your facility’s
compatible AC power source.
2-3 Connect your equipment’s input plugs to
the appropriate outlets on the PDU. The
LED near each outlet illuminates when
the outlet is ready to distribute live
AC power.
Note: It is recommended that you do not
connect a live load to the PDU. If the load you
intend to connect has an ON/OFF switch, please
turn the switch to OFF prior to connection.
2-4 Optional Cord Retention Procedure
Option 1 (Select Models): Use
the bridge lances located near each
receptacle to retain power cords. Tie
each equipment power cord to a bridge
lance by looping the cord and securing
it with one of the included cable ties A.
Make sure each cord can be unplugged
from the PDU without removing the
cable tie.
Option 2: Use the included C14 and
C20 plastic sleeves to secure plugs to
receptacles. Attach the sleeve to the
plug, making sure that the pull tabs B
remain outside the plug and that the fit
is secure. To unplug equipment properly,
use the pull tabs to remove the plug
and sleeve from the receptacle.
For Installation
Purposes Only
Hardwire Installations
(PDU3XVSRHWA & PDU3XVSRHWB models only)
2-5 These models do not come equipped
with an input cable. Conduit and
adapters are installed to the endplate A,
wires are channeled through the conduit
and adapters to the terminal block,
located behind the access plate B.
WARNING
Only qualified personnel should perform hardwire installations. Wire codes and
requirements differ from area to area. Be sure to conform to local electrical
requirements.
18-12-188-9332B8.indb 6 12/20/2018 5:19:16 PM

2-6
Remove Access Plate Screws
7
Installation
Networking the PDU
Your PDU can receive IP address assignments via DHCP server (dynamic) or static (manual)
addressing methods. See the SNMPWEBCARD installation guide on the included CD or visit
www.tripplite.com/manuals. If you are uncertain which method to use, contact your network
administrator for assistance before continuing the configuration process.
Note: The MAC address of the PDU (12-digit string in this format: 000667xxxxxx) is printed on a label attached
to the PDU enclosure. For static IP address assignments, use the RJ-45 to DB9 configuration cable (part
number 73-1243) included with the PDU.
2-6 To access the terminal block to make
input wire connections, remove the
access plate located on the back side of
the PDU.
Ground Terminal
X
Y
Z
N
18-12-188-9332B8.indb 7 12/20/2018 5:19:16 PM

A
BC DE
8
Digital Display
A3-Digit Display: Shows measured or calculated values such as Amperage, Kilowatts,
Voltage, Power Unbalance Percentage, Temperature and Humidity.
BArrow Buttons: Scroll through indicated Outlet, Input, Bank, Power, Load Balance, Sensor
and Display Brightness options using these buttons. A long press of the up or down arrow
buttons allows the user to skip to the next sequential measurement category.
CMode Button: When a menu option is selected using the Arrow Buttons, the Mode Button
scrolls through the sub-options within each category. Sub-options are shown by the
Indicator LEDs.
DIndicator LEDs: Lit LED indicates which value is being displayed on the 3-digit screen.
Amps (A): When selected, the load on the selected Input Phase (L#), Load Bank (B#)
or Outlet (##) is displayed in amps.
Wattage (kW): When selected, the load on the selected Load Bank (B#), Outlet (##)
or Total Output Power (OP) is displayed in kW.
Voltage (V): Input Phase (L#), Load Bank (B#) or Outlet (##) voltage is displayed.
Unbalanced Load (%UB): When lit, the display shows the unbalanced load
percentage deviance from the average measured value. The percentage for the phase
with the highest deviance is displayed.
Temperature (T): If Tripp Lite ENVIROSENSE is connected, the ambient temperature
will be displayed when this option is selected. The temperature is displayed in Celsius
by default, but can be switched to Fahrenheit.
Relative Humidity (%RH): If Tripp Lite ENVIROSENSE is connected, the relative
humidity percentage will be displayed when this option is selected.
E2-Digit Display: This display indicates which Input Phase (L#), Load Balance (UB), Load
Bank (B#), Output Power (OP), Outlet (##) or Sensor (S#) option is selected.
18-12-188-9332B8.indb 8 12/20/2018 5:19:17 PM

65
4LOAD L2
BANK 1
LOAD L1
BANK 1 3
21
LOAD L1
BANK 1
1211
10 LOAD L1
BANK 2
LOAD L3
BANK 1 9
87
LOAD L1
BANK 2
LOAD L3
BANK 1
LOAD L2
BANK 1
STATUS
LINK
RESET
ENVIROSENSE
1817
16 LOAD L3
BANK 2
LOAD L2
BANK 2 15
1413
LOAD L3
BANK 2
LOAD L2
BANK 2
CONFIG
STATUS
LINK
RESET
ENVIROSENSE
CONFIG
B1 B3 B5
B2 B4 B6
9
Digital Display
Load Bank Receptacle Location
Display References for 208V Models
LOAD BANKS REFERENCE
SILKSCREEN LABEL DESCRIPTION 2-DIGIT DISPLAY REFERENCE
L1-L2, BANK 1 B1
L2-L3, BANK 2 B2
L3-L1, BANK 3 B3
L1-L2, BANK 4 B4
L2-L3, BANK 5 B5
L3-L1, BANK 6 B6
INPUT PHASE REFERENCE
INPUT PHASE REPORTED 2-DIGIT DISPLAY REFERENCE
INPUT PHASE L1 – L2 L1
INPUT PHASE L2 – L3 L2
INPUT PHASE L3 – L1 L3
Button Response Definitions:
Configuration1Switch Action Control Function
Standard
Up Pushbutton
Depress ½ sec Sequentially, moves up one selection in
the menu.
Depress 3 sec Advances up to the next measurement
category.
Down Pushbutton
Depress ½ sec Sequentially, moves down one selection in
the menu.
Depress 3 sec Advances down to the next measurement
category.
Mode Pushbutton
Depress ½ sec Displays available options for a given
measurement category.
Depress 3 sec Selects the chosen available option for a given
configuration category.
Alternate
Up Pushbutton
Depress ½ sec Sequentially, moves down one selection in
the menu.
Depress 3 sec Advances down to the next measurement
category.
Down Pushbutton
Depress ½ sec Sequentially, moves up one selection in the
menu.
Depress 3 sec Advances up to the next measurement
category.
Mode Pushbutton
Depress ½ sec Displays available options for a given
measurement category.
Depress 3 sec Selects the chosen available option for a given
configuration category.
1Configured via Configuration Category item “Outlet Indicator LED Color Code Options”.
18-12-188-9332B8.indb 9 12/20/2018 5:19:17 PM

i 5.5
L i
2 0 8
L i
i 5.5
L2
2 0 8
L2
i 5.5
L3
2 0 8
L3
10
Using the Digital Display
Scrolling Through Input Phases and Options
(Measurement Category)
Press Mode button to toggle between options and data within a menu. A momentary press of the
arrow buttons switches between menus. A long press skips between measurement categories.
The scrolling pattern of the display is outlined below. Note: Three dashes will be shown in the
3-digit display when the input phase voltage is unknown, due to abnormal tripped breaker
conditions.
Input Phase 1
Input Phase 2
Input Phase 3
Amps
Amps
Amps
Volts
Volts
Volts
To Unbalanced Load Detect
18-12-188-9332B8.indb 10 12/20/2018 5:19:17 PM