Trotec PIDS 10-20V User manual

TRT-BA-PIDS10-20V-TC2018-68-001-EN
PIDS 10-20V
EN
ORIGINAL INSTRUCTIONS
CORDLESS IMPACT DRIVER

2 EN
cordless impact driver PIDS 10-20V
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................6
Transport and storage...........................................................8
Start-up..................................................................................8
Operation .............................................................................11
Available accessories..........................................................12
Errors and faults..................................................................12
Maintenance ........................................................................13
Disposal ...............................................................................14
Declaration of conformity ...................................................14
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of explosive substances
This symbol indicates dangers to the life and health of
persons due to potentially explosive substances.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
Wear hearing protection
Information marked with this symbol indicates that you
should wear hearing protection.
Wear safety glasses
Information marked with this symbol indicates that you
should wear eye protection.
Wear protective clothing
Information marked with this symbol indicates that you
should wear protective clothing.
Wear protective gloves
Information marked with this symbol indicates that you
should wear protective gloves.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
PIDS 10-20V
https://hub.trotec.com/?id=42992
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Observe all the safety warnings, instructions,
illustrations and technical data provided with this
power tool.
Failure to follow the instructions below may result in
electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
The term power tool used in the safety warnings refers to both
mains-operated and battery-powered electric tools (with/
without power cable).

EN 3
cordless impact driver PIDS 10-20V
General Power Tool Safety Warnings – Work area
safety
•Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
General Power Tool Safety Warnings – Electrical
safety
•Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep the cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
General Power Tool Safety Warnings – Personal
safety
•Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
•Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
•Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. The use of a dust
extraction system may reduce dust-related hazards.
•Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
General Power Tool Safety Warnings – Power tool
use and care
•Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
•Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and / or
the battery pack, if detachable, from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
•Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.

4 EN
cordless impact driver PIDS 10-20V
•Maintain power tools and accessories carefully. Check
for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
•Keep handles and gripping surfaces dry, clean and
free from oil and grease. Slippery handles and gripping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
General Power Tool Safety Warnings – Battery tool
use and care
•Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
•When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
•Under abusive conditions, liquid may be ejected from
the battery. Avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
•Do not use a damaged or modified battery. Damaged or
modified batteries can behave unexpectedly and lead to
fires, explosions or injuries.
•Do not expose a battery to fire or excessively high
temperatures. Exposure to fire or temperatures above
130°C (265°F) may cause an explosion.
•Follow all the instructions for charging and never
charge the battery or the cordless tool outside the
temperature range specified in the operating
instructions. Incorrect charging or charging outside of the
permissible temperature range can destroy the battery and
increase the risk of fire.
General Power Tool Safety Warnings – Service
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
•Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
Device-specific safety warnings for cordless impact
drivers/ cordless impact wrenches
•Secure the workpiece. The grip of tensioning devices or a
vice is more secure than holding the workpiece only by
hand.
•Hold the power tool firmly. When tightening or loosening
screws, high reaction torques can occur temporarily.
•Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
•For any work on the device, as well as during transport
or storage, set the switch for the rotational direction to
centre position (locked). This prevents unintentional
starting of the power tool.
•Regularly check the tool holder for wear or damage.
•Only start a percussive power tool while holding it
against the workpiece.
•Wait until the power tool has come to a standstill,
before putting it down.
Intended use
Only use the device PIDS 10-20V:
• for screwing in and loosening screws
• for tightening and loosening nuts
whilst adhering to the technical data.
We recommend using the power tool with original Trotec
accessories.
Improper use
The device is not intended for drilling.
Personnel qualifications
People who use this device must:
• have read and understood the instructions, especially the
Safety chapter.

EN 5
cordless impact driver PIDS 10-20V
Personal protective equipment
Wear hearing protection.
Excessive noise can lead to hearing loss.
Wear eye protection.
With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear protective gloves.
They protect your hands from burns, crushing injuries
and skin abrasions.
Wear tight-fitting protective clothing.
This protects you from the draw-in and entanglement
hazard posed by rotating parts.
Residual risks
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket and the battery from the device!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of explosive substances
Do not expose the battery to temperatures above
45°C! Do not let the battery come into contact with
water or fire! Avoid direct sunlight and moisture. There
is a risk of explosion!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Before the device is switched on, the accessory must
be firmly locked in place in the tool holder. If the
accessory is not properly locked, it can be catapulted
out of the tool holder uncontrollably upon switch-on.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
Caution
Keep a sufficient distance from heat sources.
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Note
Only change the rotational direction when the device is
at a standstill! Otherwise the device might be
damaged.

6 EN
cordless impact driver PIDS 10-20V
Information about the device
Device description
The cordless impact driver PIDS 10-20V is ideally suited for
screwing in or tightening and loosening screws and nuts.
With its rotary percussion pulses, the device generates a very
high torque, which is particularly well suited for loosening
seized or rusted screws and nuts.
The tool holder with locking mechanism further enables a tool-
free exchange of accessories.
The integrated LED work light offers an improved illumination of
the workpiece or working surface.
The battery comes with its own battery level indication. As a
result you can check the current charging status without having
to connect it to the device.
Device depiction
1
2
3
4
5
14
15
6
13
12
7
8
11
9
10
No. Designation
1Tool holder with locking mechanism
2Clockwise/ counter-clockwise rotation, lock
3On/off switch (speed regulation)
4Handle
5Belt clip
6Battery
7Quick charger
8Red battery LED (battery charging)
9Bit extension 1/4" 50 mm
10 Square socket adapter 1/4"
11 Green battery LED (quick charger ready for operation)
12 3-stage battery level indication
13 Release button
14 Battery holder
15 LED work light
Scope of delivery
• 1 x Cordless impact driver PIDS 10-20V
• 1 x Rechargeable battery
• 1 x Quick charger
• 1 x Square socket adapter1/4"
• 1 x Bit extension1/4" 50mm
• 1 x Belt clip
• 1 x Transport case
• 1x Manual

EN 7
cordless impact driver PIDS 10-20V
Technical data
Parameter Value
Model PIDS10-20V
Nominal voltage 20V
Idle speed 0–2800rpm
Impact frequency 0–3600spm
Tool holder 1/4"hexagon socket
Tool holder with square socket
adapter
External 1/4"square retainer
Max. screw diameter
Wood
Metal
8mm
8mm
Max. torque 180 Nm
Weight 1.6kg
Battery Multiflex 20–2.0DC
Type Li-ion
Nominal voltage 20V
Capacity 2Ah
Quick charger Multiflex 20–2.0AC
Input
Nominal voltage 230 – 240V/ 50Hz
Power consumption 65W
Output
Nominal voltage 21.5V
Charging current 2.4A
Charging time 1 h
Protection class II/
Sound values according to EN62841-2-2
Sound pressure level LpA 93.9dB(A)
Sound power level LWA 104.9dB(A)
Uncertainty K 3dB(A)
Vibration information according to EN62841-2-2
Vibration emission value ah13.43m/s2
Uncertainty K 1.5m/s2
Wear hearing protection.
Excessive noise can lead to hearing loss.
Information on noise and vibration:
• The specified total vibration and noise emission values
were measured by means of a test procedure standardized
in EN62841 and can be consulted for the comparison of
one power tool with another.
• The specified total vibration and noise emission values
can also be used for preliminary load assessment.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
• The actual vibration and noise emission may differ from
the stated values during operation of the power tool. This
depends on how the power tool is used and especially on
the type of workpiece being processed. Try to keep the
vibration load to a minimum. Exemplary measures for
reducing the vibration load include wearing gloves during
operation of the tool and the limitation of working hours.
All parts of an operating cycle must be considered for this
(e.g. times at which the power tool is switched off and
times when it is switched on but runs without load).

8 EN
cordless impact driver PIDS 10-20V
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
For transporting the device, use the transport case included in
the scope of delivery in order to protect the device from external
influences.
Before transporting the device, observe the following:
• Switch off the device by setting the switch for clockwise/
counter-clockwise rotation to centre position(lock).
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
• Remove the tool from the tool holder.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
– Please also observe any other national regulations.
Storage
Before storing the device, observe the following:
• Switch off the device by setting the switch for clockwise/
counter-clockwise rotation to centre position(lock).
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
• Remove the tool from the tool holder.
• Clean the device as described in the Maintenance chapter.
• For storing the device, use the transport case included in
the scope of delivery in order to protect the device from
external influences.
• Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• ambient temperature below 40 °C
• protected from dust and direct sunlight inside the transport
case
Start-up
Unpacking the device
• Take the transport case out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
• Check the contents of the transport case for completeness
and look for damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.

EN 9
cordless impact driver PIDS 10-20V
Charging the battery
Note
The battery can be damaged in case of improper
charging.
Remove the charger's mains plug before inserting or
removing the battery.
Never charge the battery at ambient temperatures
below 10°C or above 40°C.
The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red
LED in the battery level indication(12) is illuminated), the
battery should be charged. To do so, please proceed as follows:
1. Slide the battery(6) onto the quick charger(7) upside
down until it locks in place.
1 h
6
7
11
8
2. Insert the mains plug of the quick charger(7) into a
properly fused mains socket.
ðThe red battery LED(8) lights up.
ðCharging requires approx. one hour.
3. Wait until the red battery LED(8) goes off and the green
battery LED(11) lights up.
ðThe battery(6) is fully charged.
4. Hold onto the mains plug while pulling the power cable of
the quick charger(7) out of the mains socket.
ðThe battery(6) and the quick charger(7) may have
become warm during charging.
Allow the battery(6) to cool down to room temperature.
5. Take the battery(6) out of the quick charger(7) by
pressing and holding the release button(13) and pulling
the battery(6) off the quick charger(7).
Inserting the battery
1. Set the switch for clockwise/ counter-clockwise
rotation(2) to centre position(lock).
2. Slide the battery(6) onto the device until it locks in place.
2
6
Removing the battery
1. Set the switch for clockwise/ counter-clockwise
rotation(2) to centre position(lock).
2. Detach the battery(6) from the device by pressing and
holding the unlocking button(13; I.) and pulling the battery
off the device(II.).
I.
II.
2
6
13
3. If required, charge the battery(6) as described in the
section Charging the battery.

10 EN
cordless impact driver PIDS 10-20V
Checking the battery status
The battery status is displayed as follows by the three LEDs of
the battery level indication(12):
LED colour Meaning
Green – Orange – Red maximum charge / power
Orange – Red medium charge / power
Red weak charge – Recharge the
battery.
1. Press on the battery icon(16) on the battery(6).
ðYou can read the battery status from the battery level
indication(12).
16
12
Tool change
The device is equipped with a tool holder with locking
mechanism for hexagon bits. Please proceed as follows to
remove or insert tools:
1. Set the switch for clockwise/ counter-clockwise
rotation(2) to centre position(lock).
2. Push the locking mechanism at the tool holder(1) to the
front and hold it in place.
3. Remove the tool from the tool holder(1), if any.
1
4. Insert the desired tool in the tool holder(1).
9
Info
Please note that when using short bits you first have to
insert the supplied bit extension(9) into the tool
holder(1). Then insert the short bit into the bit
extension(9).
5. Let go of the locking mechanism at the tool holder(1).
Info
When unscrewing screws or loosening nuts, note the
setting of the rotational direction! On the clockwise/
counter-clockwise rotation direction indicator(2) you
can see in which direction the screws or nuts will be
screwed.

EN 11
cordless impact driver PIDS 10-20V
Using sockets
If you want to screw hexagon screws or nuts, you can use the
supplied square socket adapter(10) and a socket. To do so,
please proceed as follows:
1. Insert the square socket adapter(10) into the tool
holder(1) as described in the chapter Tool change.
2. Slide the matching socket onto the square socket
adapter(10) until it perceptibly clicks into place.
10
3. Check the socket for tight fit.
Operation
Wear hearing protection.
Excessive noise can lead to hearing loss. The sound
pressure level LpA of this device amounts to 93.9dB(A).
Tips and notes on handling the cordless impact driver/
cordless impact wrench
General information:
• Check the tool in the tool holder for proper fit before every
application.
• The centre position of the clockwise/ counter-clockwise
rotationswitch (lock) is suited for work breaks or tool
change.
Screwing:
• In case of soft wood, screws can be screwed in without
pre-drilling.
• In case of hard wood or large screws, it is recommended
to use a drill for pre-drilling.
• When using countersunk screws, the drill hole should be
countersunk beforehand.
• Especially smaller screws and bits may be damaged when
selecting an excessive torque and / or speed at the tool.
Selecting the rotational direction
Note
To avoid damaging the gear, only change the rotational
direction when the device is at a standstill.
The motor's rotational direction can be changed by means of
the switch for clockwise/ counter-clockwise rotation(2).
1. Press the switch for clockwise/ counter-clockwise
rotation(2) in all the way on that side towards which the
motor shall rotate.
I. II.
2
I. Screwing in II. Unscrewing
2. Carry out a short test run to see whether the rotational
direction matches the intended application. A wrong
rotational direction may damage the tool and/ or
workpiece.
3. If required, set the switch for clockwise/ counter-
clockwise rotation(2) to centre position (lock) to block the
on/off switch(3).

12 EN
cordless impact driver PIDS 10-20V
Switching the device on and off
The device has an infinitely variable speed control. The more
firmly you push the on/off switch(3), the higher is the speed.
1. Check whether the fixed tool is suitable for the intended
application.
2. Check whether the workpiece is secured and the worktop
prepared correspondingly.
3. Press and hold the on/off switch(3) during screwing.
ðThe device operates with the previously selected
settings.
ðThe LED work lamp(15) is illuminated.
3
15
4. Let go of the on/off switch(3) to stop the device.
ðThe LED work lamp(15) goes out.
Info
The motor has an integrated brake that quickly stops
the motor once you let go of the on / off switch(3).
Shutdown
1. Set the switch for clockwise/ counter-clockwise
rotation(2) to centre position(lock).
2. If required, allow the device to cool down.
3. Remove the battery from the device (see Start-up chapter).
4. Remove the tool from the device (see Start-up chapter).
5. Clean the device according to the Maintenance chapter.
6. Store the device according to the Storage chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the instructions.
Using insertion tools or accessories other than those
specified in the instructions may cause a risk of injury.
Accessories Article number
Spare battery Multiflex2.0Ah 20V 6.200.000.303
Screw bit set, 32-piece 6.200.001.001
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Slight smoke or odour are emitted during first use:
• This is not a fault. These phenomena disappear after a
brief runtime.
The battery does not charge:
• Check whether the battery is correctly connected to the
quick charger.
Slide the battery into the quick charger in a way that the
battery terminals engage in the quick charger. The battery
must lock in place in the quick charger.
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the fuse (home).
• Check the quick charger for damages. Should the quick
charger be damaged, stop using it. Contact the Trotec
customer service.
• Check the battery terminals for dirt. Remove any dirt.
• The battery might be defective and have to be replaced.
Only use batteries of the same type.

EN 13
cordless impact driver PIDS 10-20V
The device does not start:
• The battery power might be too low. Recharge the battery.
• Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
• Check the position of the clockwise/counter-clockwise
rotation switch. The switch must be pressed in all the way.
If the clockwise/counter-clockwise rotation switch is in
centre position (lock), the on/off switch is blocked.
• Check the battery terminals for dirt. Remove any dirt.
Info
Wait for at least 10 minutes before switching the
device back on.
The on/off switch cannot be pressed:
• Check whether the clockwise/counter-clockwise rotation
switch is in centre position (lock). Set the desired rotational
direction to unlock the tool.
The device becomes hot:
• Keep the venting slots clear to prevent the motor from
overheating.
Info
Wait for at least 10 minutes before switching the
device back on.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug or the battery with wet or
damp hands.
• Switch off the device.
• Allow the device to cool down completely.
• Remove the battery from the device.
Warning of electrical voltage
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Notes on maintenance
Inside the device, there are no parts that need to be maintained
or lubricated by the user.
Cleaning
The device should be cleaned before and after each use.
Note
The device does not have to be lubricated after
cleaning.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
• Clean the device with a soft, damp and lint-free cloth.
Make sure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.
• Dry the device with a soft, lint-free cloth.
• Dry the bits with a soft, lint-free cloth.
• Keep the connecting terminals on the device and charger
clean.
• Keep the ventilation openings free from dust deposits to
prevent overheating of the motor.

14 EN
cordless impact driver PIDS 10-20V
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Li-Ion
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
Declaration of conformity
The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at https://hub.trotec.com/?id=42992.
Declaration of conformity
In accordance with the ECMachinery Directive 2006/42/EC,
AnnexII, part1, SectionA
Herewith, we– Trotec GmbH&Co.KG– declare that the
machinery designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.
Product model/ Product: PIDS 10-20V
Product type: cordless impact driver
Year of manufacture as of: 2019
Relevant EU directives:
• 2014/30/EU: 29March 2014
Applied harmonised standards:
• EN 62841-1:2015
• EN62841-2-2:2014
Applied national standards and technical specifications:
• AfPS GS 2014:01
• EN 55014-1:2017
• EN 55014-2:2015
Manufacturer and name of the authorised representative of
the technical documentation:
Trotec GmbH & Co. KG
Grebbener Straße 7, D-52525 Heinsberg
Phone: [phone]
E-mail: [email protected]
Place and date of issue:
Heinsberg, 25.02.2019
Detlef von der Lieck, Managing Director

Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com