TruXedo Lo Pro User manual

NOTE:The trigger latch is included on the driver side rail only.
End Plug Seal
Position the driver side
rail (A) against the truck
bed rail. With the tailgate
closed, slide the rail back
until the rear seal is
slightly compressed
against the tailgate.
Adjust the rail vertically
so that the seal is flush
with the truck bed caps.
Trigger Latch
3 4
The serial number for the cover is located here.
For future reference, write it here:
___________________________________.
OWNER'S MANUAL
Damaged or missing parts? Call 877-878-9336 Mon - Fri 8 a.m. - 5 p.m. CT
Parts will be shipped to you factory direct. Do not return kit to place of purchase.
To view install video visit truxedo.com/lopro
It is important that all areas where the bed cover mounts are
clean and free of debris prior to installing.
TOOLS REQUIRED:
•Flat head screwdriver
•1/2" wrench or socket
A
B
C
D
1 2
TruXedo Inc. • 2209 Kellen Gross Drive Yankton, SD 57078 • 877-878-9336 • truxedo.com ©TruXedo Inc., 2021 Part# 1118085 Rev. C 03.10.2021
TOOLS RECOMMENDED:
•Spring clamps
•Scissors/ulity knife
PARTS INCLUDED
IN YOUR KIT:
Driver side rail
Passenger side rail
Cover assembly
6x clamps
Bulkhead seal (on select make/models)
A
B
C
D
E
DE
Attach clamps (D) starting in the middle. Evenly space 3
clamps along the driver side rail (A), leaving approximately
8" on each end. Finger tighten to make sure the teeth of the clamp
engage with the grooves of the side rail. Then tighten all clamps
with a 1/2” socket or wrench. Repeat steps 4 & 5 on the passenger
side rail (B).
D
NOTE:The use of spring clamps to hold the side rail in place can
assist during the installaon process.

Place the cover (C) on the side rails towards the front of the truck bed (near the cab). The front header seal is designed to help shed
water and should be sing on top of the bulkhead.
Clamp Assembly
Height
Flush
Side Rail
Level
With Bed
Cap
To connect the cover assembly (C) to the side rails (A & B), slide the right and le header guides into the locked posion. A clicking
sound will indicate a secure aachment.
Truck
Bed Cap
LEFT HEADER GUIDE RIGHT HEADER GUIDE
5
For optimal latching performance and cover fit, the side rails
(A & B) should be level with the truck bed caps and not tilted
up or down. To fine-tune side rail tilt, you can reposition the clamps.
To adjust the rail tilt upwards, move the clamp as high as you can.
To adjust the rail tilt lower, slide the clamp downwards toward the
bottom of the rail. Tighten all clamps with a 1/2” wrench or socket.
7
8
Trigger Latch
6
E
TruXedo Inc. • 2209 Kellen Gross Drive Yankton, SD 57078 • 877-878-9336 • truxedo.com ©TruXedo Inc., 2021 Part# 1118085 Rev. C 03.10.2021
Front Header Seal
Bed Rail
Side View
Bulkhead
If a bulkhead seal (E) is included with the cover, clean the top
of the bulkhead to install the seal. Peel the backing and adhere
the seal from one bedrail edge to the other. Remove any excess with
scissors or a utility knife. If the truck has a drop-in bedliner, no seal
will be needed.

REMOVING THE COVER
To remove the cover from the side rails, push up on the retainer tab and then slide the header guide away from the side rail. Do this on
both the driver and passenger side. Carefully lift the cover off the side rails.
Push Up To
Release
Slide Header Guide To Slide Header Guide To
Disengage.Disengage.
Passenger
Side Shown
Header Guide
Retainer Tab
To drive with the cover in the open position, pull the latch towards
you to release the cover (located on driver side rail). Roll the cover
toward the cab of the truck, making sure that both sides roll
evenly. Secure the cover by placing both retainer hooks into the
retainer loops. You are ready to drive with the cover in the open
position.
COVER IN THE OPEN POSITION
Disengage the retainer hooks from the retainer loops and
unroll the cover towards the tailgate.
9 10
11
NOTE: If the tailgate has a key lock, the cover is secured unl
the tailgate is unlocked and opened.
CLICK
A clicking sound will indicate a correctly installed cover. Next
secure the hook and loop fastener along the enre length
of both side rails before driving the vehicle. Simply run your hands
down both sides of the cover to achieve this. This will prevent wind
from liing the cover and causing possible damage. You are ready to
drive with the cover in the closed posion.
Place the rear header into the header stops which are
located on both side rails. Rotate the rear header downwards
unl you feel the cover latch in place.
Rear Header
Header Stop
Trigger Latch
NOTE: We recommend closing the tailgate rst and then closing the cover.
Pull Latch
Retainer Loop
Retainer Strap
Retainer Loop
Retainer Strap
Retainer Hook
TruXedo Inc. • 2209 Kellen Gross Drive Yankton, SD 57078 • 877-878-9336 • truxedo.com ©TruXedo Inc., 2021 Part# 1118085 Rev. C 03.10.2021

WARRANTY DURATION
TruXedo®, Inc. (“TruXedo”) oers a LIFETIME warranty on Lo Pro, Deuce and Pro X15. Warranty is limited to original purchaser of truck bed
cover and is nontransferable. The warranty registraon must be on le and/or proof of original purchase (detailed and dated receipt)
required for warranty service.
WARRANTY CONDITIONS
This warranty is against defecve materials or workmanship. The warranty is void if the product has been damaged by accident, unreasonable
use, neglect, improper service/installaon/removal, modicaons, normal wear and tear or other causes not arising out of defecve materials
or workmanship. Consequenal and incidental damages are not covered under this warranty. TruXedo's obligaon under this warranty is
limited to repairing or at its opon, replacing any part that is returned, transportaon prepaid, to Yankton, South Dakota, if the product is, in
our judgement, defecve. All materials must be accompanied by an RMA (Return Material Authorizaon) number requested by and autho-
rized in advance of returning the materials. TruXedo shall not be liable or responsible to supply or pay labor to replace any part found defec-
ve, nor shall it be liable for any damages of any kind or nature to person, product, or property.
• Please register the warranty online at truxedo.com
• Direct all warranty claims to TruXedo at 877-878-9336
• For available installaon videos, visit the TruXedo YouTube channel
The Following Condions will Void Warranty:
•Wind Whip Damage – The cover must be secured at all points when the vehicle is in motion. An unsecured cover will flap,
resulting in damage to the vinyl fabric.
•Improper Cleaning – It is recommended to use the tested and approved TruXedo Pro-Tex or clean with soap and water only.
Do not use vinyl conditioners (e.g. Armor All®) because they will shrink the vinyl.
•Overloading of Cargo – Cargo should not contact the tarp at any point. Protrusions in the tarp will stress the vinyl fabric.
Cargo may also shift while traveling causing it to press against the vinyl fabric and damage it.
OWNER/USER RESPONSIBILITIES
It is the responsibility of the owner/user to read this manual and comply with the operang procedures. The owner/user is also responsible
for inspecng the TruXedo cover and for having parts repaired or replaced when worn or damaged. Failure to follow safety instrucons and
warning labels could result in failure of your cover system and/or personal injury.
IMPORTANT OPERATING TIPS
• DO NOT roll cover into rear cab window. DO NOT stow against cab.
• Aer closing the cover, the operator must secure the hook and loop by running their hand down the driver and passenger side rails,
pushing down on the cover material.
• If the side rails are pping, adjust the clamps in order to level the side rails and ensure a proper t.
• The tonneau cover must be free of foreign material including snow and ice before rolling open or closed.
Passenger
Side Rail
Front Header
Spring Plunger
NOTE:Adjust tension in small increments.
Slight adjustments will gain signicant results.
TURN SPRING PLUNGER
SCREW CLOCKWISE
COVER TOO LOOSE
Opmal Gap is
1/16"
DURING WARMEST
PART OF DAY
CORRECT TENSION
DETAIL C
Lo Pro is equipped with Automatic Tension Control. This helps compensate for material expansion and contraction caused by extreme
temperature changes. Proper tension allows the cover to look and perform at its best. While preset at the factory, you can check cover
tension after installation as well as seasonally.
AUTOMATIC TENSION CONTROL ADJUSTMENT
If the cover feels too ght or too
loose when opening or closing
it, adjust the tension during the
warmest part of the day. With the
cover closed, release the hook
and loop fastener from both side
rails near the cab. Check
compression of both spring
plungers against the front header
per Detail C. Roll the cover open
and with a flat head screwdriver
make adjustments. Repeat until
satisfactory tension has been
achieved.
TruXedo Inc. • 2209 Kellen Gross Drive Yankton, SD 57078 • 877-878-9336 • truxedo.com ©TruXedo Inc., 2021 Part# 1118085 Rev. C 03.10.2021

SAFETY INSTRUCTIONS
• DO NOT place objects on or against the cover or framework.
• DO NOT tie cargo to truck bed cover framework.
• DO NOT attempt to drive with the cover in the partially open position.
• DO NOT operate the vehicle with objects on top of the cover.
• NEVER allow children or pets to occupy the pickup box while the cover is closed.
• Cover is not airtight. Special care is required to keep cargo clean and dry.
•Tonneau covers won’t prevent theft of contents inside the truck box.
• The cover assembly (tarp) must be rolled fully open and secured with retainer straps when towing the vehicle backwards.
• If the cover is going to be rolled open for an extended amount of time, periodically re-roll the cover and secure the retainer
straps to ensure the cover doesn’t rest against the cab of the truck.
• A fully rolled cover in the open position must always be secured with retainer straps.
TROUBLESHOOTING TIPS
•WRINKLES ON THE VINYL FABRIC AFTER ROLLING COVER CLOSED
o Pull the vinyl fabric taut from each side. For best results, the help of a second person pulling on the opposite side is
preferable.
•SAGGING VINYL FABRIC BETWEEN THE CROSS BOWS
o Adjustment to Automatic Tension Control may be required.
•WIND LIFTS UP THE EDGE OF THE VINYL FABRIC
o Make sure to engage the hook and loop on the driver and passenger side rails after closing the cover. This may need to be
done periodically when taking long trips.
•VINYL FABRIC FLUTTERS EXCESSIVELY WHEN DRIVING
o Check cover tension, refer to Automatic Tension Control section.
oMake sure hook and loop fasteners are set. See Step 11.
•SNOW AND ICE ACCUMULATION ON THE VINYL FABRIC
oUse broom or brush to remove loose snow and ice. DO NOT use sharp or pointed tools to remove snow and ice.
oDirect sunlight will help melt snow and ice off the vinyl fabric.
•TONNEAU COVER WILL NOT LATCH
o Check side rails to make sure they are level. See Step 5.
oMake sure the header seal is not caught between side rails & header.
oCheck the position of side rails on the pickup box. They may be positioned too low. See Step 5.
oMake sure the cover has proper tension. See Automatic Tension Control section.
•VINYL FABRIC IS TOO TIGHT OR TOO LOOSE
o See Automatic Tension Control to adjust the tension.
•VINYL FABRIC HAS SHIFTED TOO FAR TO ONE SIDE
o Unlatch the cover at the tailgate, release the hook and loop along both sides, go to the shorter side of the tarp and tug. The
vinyl fabric will slide in the aluminum headers. Pull on the shorter side until the tarp appears centered on the whole system.
Latch the cover and secure the hook and loop down both sides. Repeat if more adjustment is needed.
COVER CARE AND MAINTENANCE
•It is recommended to use the tested and approved TruXedo Pro-Tex or clean with soap and water only.
Do not use vinyl conditioners (e.g. Armor All®) because they will shrink the vinyl.
•It is recommended that you periodically check that the cover is securely attached to your truck bed. Inspect the clamps and front
header guide slides to ensure they were properly installed and have not come loose during operation.
•It is recommended that you periodically inspect and service the rear latch closure. Clean away any excess dirt or grime.
•Covers that are used frequently or are subject to vibrations and impacts from rough roadways may require adjustment.
FAQ
•WHY IS THERE A HOLE PUNCHED AT THE REAR OF THE PASSENGER SIDE RAIL OF THE TRUXEDO LO PRO, DEUCE AND PRO X15 BUT
NO LATCH?
All side rails are punched idencally to keep them uniform, to ensure manufacturing eciency and to reduce tooling costs. By doing
this, TruXedo can build and ship more covers while maintaining compevely priced products of the highest quality.
•WHY IS MY COVER HOLDING WATER AFTER IT RAINS?
Water pooling on the cover is normal because our cross bows are not arched. Since they are designed to sit at some water may
accumulate on the top of the cover. Once you drive your truck, the water will shed from the cover. Make sure to reghten the hook
and loop fasteners along the length of the bed.
TruXedo Inc. • 2209 Kellen Gross Drive Yankton, SD 57078 • 877-878-9336 • truxedo.com ©TruXedo Inc., 2021 Part# 1118085 Rev. C 03.10.2021

11 ___*___ Extruded Retainer Loop
12 ___*___ Header Seal Rear
13 1705052 End Plug, 1" OD
14 ___*___ Black Bow
15 1702992 Spring Plunger, 5/8" x 2.15"
16 1703260 Tension Control Bracket
17 1115354 Header Insert Retainer Clip
18 ___*___ Hook and Loop Fasteners
19 1703332 Hitch Pin, 1/16" x 1 5/16"
20 1705392 Aluminum Clamp Assy
21 ___*___ Side Rail, Passenger's Side
22 ___*___ Side Rail, Driver's Side
23 1114773 Flat Spring, 5/8" x 3 7/8"
24 1704213 Latch Assembled
25 1702926 Cap Screw, 5/16" x 7/8"
26 1704187 Header Stop
27 1118094 Side Rail End Plugs w/Seal (Set of Two)
28 1705629 Square Head Screw (#1 Drive)
29 1117467 Rear Header 08 End Plugs (Set of Two)
30 ___*___ Black Rear Header
* Please specify length or make and model of vehicle.
1___*___ TruXedo Lo Pro Replacement Cover
2___*___ Black Front Header
3___*___ Header Seal Front
4 1117540 Front Header 08 End Plugs (Set of Two)
5 1704707 Header Guide
6___*___ Retainer Strap
7 1700428 Washer Flat 5/16"
8 1704606 Cap Screw, 5/16-18 x 5/8"
9 1117591 Header Guide Retainer
10 1704194 Weld Nut 5/16-18 ZP
3"
2
12
4
6
8
1
3
5
7
9
13
16
17
20
21
24
25
28
29
28
5
10
11
14
15
18
19
22
23
26 27
30
27
2
TRUXEDO LOPROREPLACEMENT PARTS
TruXedo Inc. • 2209 Kellen Gross Drive Yankton, SD 57078 • 877-878-9336 • truxedo.com ©TruXedo Inc., 2021 Part# 1118085 Rev. C 03.10.2021