Tubz Toyz User manual

2

3
Step 1:
Each tower is shipped as two boxes the large tower box and the smaller stand box. Open
each of the boxes and inventory each of the parts before starting assembly to ensure all
parts have arrived.
The larger tower box contains the tower machine, a set of Silver 100 Lid Keys, and a set of
Black 002 Coin Box Keys

4
Note: Some tower units will arrive pre-stickered
The smaller stand box includes the post, the base, the tower plate, 4x large bolts, 4x small
bolts, 4x black bolts, 4x nuts, and 4x locking washers.

5
The tools you will need:
1: 7/16 Wrench
1: 9/16 Wrench
Step 1:
Start by standing the post up so that the 4 square holes are facing up
Step 2:
Flip the base upside down and lay it on top of the post making sure to line the square
holes up with the holes on the base

6
Step 3:
Place the Large Bolt in from underneath then place on the Locking Washer and one
nut
Step 4:
Place on the Locking Washer and Nut then tighten with a 9/16 wrench
Repeat 3 more times into all 4 Large Bolts are secure

7
Step 5:
Now filp the post and stand it upright
Note: The Large bolt should fit flush into the square hole and lay flush
on top of the base.

8
Step 6:
Place the tower plate on top of the post
Note: May have to spin the tower plate to line up with the following holes

9
Step 7:
Once the holes are aligned screw in the 4 small bolts into the tower plate
Tighten them with a 7/16 wrench

10
Step 8:
Underneath the tower machine are four rubber leg pegs. These are when your
machine is to be used on the counter top with no post.
If you are using the post remove the four rubber leg pegs and set them aside we will
be using them again shortly
Note: Notice the Shape that the legs holes are in with two holes closer together then
the other two holes. This Is important because the machine will only fit onto the post in
certain direction. So spin the tower until the holes are aligned

11
Step 9:
Now place the machine on top of the posts aligning the holes mentioned in step 8
Now you can fasten the machine to the post using either the 4x rubber leg pegs you
removed in Step 8. Alternatively, you can use the 4x black bolts the choice is yours
Note: Before fully securing the tower to the tower plate please make sure to hold on to
machine securely

12
The tools you will need:
1: 10mm Socket
1: 9/16 Wrench
Step 1:
Start by standing the post up so that the side with 3 holes is facing up

13
Step 2:
Flip the chrome base upside down and lay it on top of the post making sure to line the
three holes up with the holes on the base
Step 3:
Place on the square plate

14
Step 4:
Secure with the 4x large bolts and tighten with a 9/16 wrench
Step 5:
Once large bolts are secure flip the entire post right side up

15
Step 6:
Place the tower plate on top of the post
Step 7:
Secure the tower plate with the 4x Small Bolts in these 4 holes
Tighten the 4x Small Bolts with the 10mm Socket Wrench

16
Step 8:
Underneath the tower machine are four rubber leg pegs. These are when your
machine is to be used on the counter top with no post.
If you are using the post remove the four rubber leg pegs and set them aside we will
be using them again shortly
Note: Notice the Shape that the legs holes are in with two holes closer together then
the other two holes. This Is important because the machine will only fit onto the post in
certain direction. So spin the tower until the holes are aligned

17
Step 9:
Now place the machine on top of the posts aligning the holes mentioned in step 8
Now you can fasten the machine to the post using either the 4x rubber leg pegs you
removed in Step 8. Alternatively, you can use the 4x black bolts the choice is yours

18
Note: Before fully securing the tower to the tower plate please make sure to hold on to
machine securely

19
Step 1:
Do a quick inventory that you have a full set of stickers for your machine
Note: Some Towers will arrive pre-stickered
Step 2:
The following are the recommended sticker placements
Place the 2x turn twice stickers on each side of the dial
making sure both are aligned to the red guide lines in photo

20
Place each of the brand stickers on each side of the machine lining up the middle of
the sticker to the seam in photo
The 2x Insert $1 stickers are placed on each side of the front mechanism align the
bottom of the sticker with the seam in photo