Tuffcare Rhino P420 User manual

RHINO PATIENT LIFTER P420 and P425
OPERATION MANUAL
ATTENTION
Before using this Medical Device read this manual. If you are unable
to understand, contact your equipment provider for technical
support before attempting to use this bed.

23
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
TABLE OF CONTENTS
3
4
6
9
10
13
13
14
15
15
16
19
19
21
24
28
32
34
34
34
34
35
Product Specifications
Product Diagram
General Guidelines
SECTION 1 - General Guidelines
SECTION 2 - Assembly
Assembling the Mast Assembly to the Base
Attach the Hi-Low Actuator to the Mast Assembly
Attaching the Control Unit on Mounting Bracket
Attaching the Battery Case on Control Unit
Prepare the Patient Lifter for Use
Locking/Unlocking the Rear Casters
Raising/Lowering the Patient Lifter
Closing/Opening the Legs
Using the Emergency Stop
Activating a Mechanical Emergency Release
Charging the Battery
Positioning the Stand up Lifter
Lifting the Patient
Moving the Patient
Transferring a Patient to a Wheelchair
Transferring a Patient to a Car
Transferring a Patient to from a Car to a Wheelchair
Maintenance Safety Inspection Checklist
Cleaning the Lifter
Detecting Wear and Damage
Lubricating the Lifter
Warranty
SECTION 3 - Operation
SECTION 4 - Lifting the Patient
SECTION 5 - Transferring the Patient
SECTION 6 - Maintenance
SECTION 7 - Limited Warranty
Height at Sling Hook-up - MAX.: 81 inches
Height at Sling Hook-up - MIN.: 36 inches
Base Width OPEN: 33.5 inches
Base Width CLOSED: 21 inches
Base Height (Clearance): 4.5 inches
Base Length: 47.5 inches
Overall Height: 81 inches
Overall Length: 47.5 inches
Overall Width: 25 inches
Casters: 3” Dual Front and 4” Rear with Brake
Sling Options: Transfer
Sling Material: Nylon/Polyester
Weight Capacity: 400 lbs
Weight without sling: P420 - 113 lbs, P425 – 117 lbs
Battery: 24V DC (RCHBL)
Charger Input: 100-240V AC
Charger Output/Charging Time: 29.5V DC Max 6 hours
Motor Safety Devices: Anti-Entrapment
Emergency Stop Button: Yes
Limited Warranty Lifter/Electronics: 3 Years/1 Year
PRODUCT SPECIFICATION
P440/445 RHINO STAND UP PATIENT LIFTER
Note: For EZ installation, the Leg Actuator is pre-assembled on the
Base for P425 model
11
11
12

45
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
PRODUCT DIAGRAM
Lift Arm
Attachment (Sling) Cradle
Hi-low Actuator
Hand Pendant
Mast
Dual Front Caster Wheels
without Brake
Adjusting Base
A
B
C
D
E
F
G
H
I
J
K
L
M
Foot Pedal for adjusting
Base (For P420)
Rear Caster Wheel with Brake
Charging Cord
Control Unit
Battery Case
Push Handle Bar
C
B
D
Manufacturer Tag
Model Number
Serial Number
Country of Origin
A
F
DANGER! RISK OF ELECTRICAL AND FIRE HAZARD. MAY
RESULT IN DEATH, SERIOUS INJURY, SHOCK OR BURNS.
This charger, like all electrical products. MUST be treated with
respect. Follow these instructions to reduce electrical hazard risk.
TO HELP REDUCE THIS RISK:
PROPER GROUNDING OF AC POWER CORD
Charger MUST be grounded to reduce risk of electric shock
Charger is equipped with an electric cord having an equipment
grounding conductor and a grounding plug. The plug MUST be
plugged into an outlet that Is properly Installed and grounded
in accordance with all local codes and ordinances. If you ever
feel even a slight shock from this or any electrical appliance, or
equipment connected to it, such as your chair or carrier STOP. Turn
off electricity to outlet, and have it inspected by an electrician. You
may have a dangerous, improperly wired outlet.
DANGER - NEVER alter AC power cord or plug provided. If
it will not fit outlet, have proper outlet installed by a qualified
electrician. Improper connection can result in a risk of an electric
shock. This battery charger is for use ona nominal 120 volt circuit
(common household current), and has a grounding plug. A
temporary adapter may be used to connect this plug to a two-
pole receptacle if properly grounded outlet is not available. The
temporary adapter should be used only until a qualified electrician
can install a properly grounded outlet.
Instruction for Adjusting
Legs (for P440 Only)
ADJUSTING LEGS
(FOR P420 ONLY)
LEGS SECTION MOTOR
(FOR P445)
P440 – SEMI HI-LOW / P445 – FULL HI-LOW WITH LEG OPENING
E
G
H
I
J
K
L
M

67
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
WEIGHT LIMIT
DO NOT exceed maximum weight limit of the patient lifter.
The weight limit for the stand up lifter is 350 lbs.
ASSEMBLING THE LIFTER
DO NOT over-tightens mounting hardware. It will cause a
damage of mounting brackets.
USING THE SLING
Be sure that sling is properly attached on sling holders before
the patient is removed from a bed, chair or any objects.
If the patient is in a wheelchair, secure the wheel locks in place
to prevent the chair from moving forwards or backwards.
OPERATING THE LIFTER
Prior to first, make sure that battery is being fully charged.
Always use the handles to move the lifter.
LIFTING THE PATIENT
Before positioning the legs of the stand-up lifter around the
patient, make sure that the patient’s feet are out of the way of
the foot plate, otherwise injury may occur.
Adjustments for safety and comfort should be made before
moving the patient. Patient’s arms should be outside of the
sling straps.
Before lifting a patient from a wheelchair, bed or any objects,
slightly raise the patient off the object and check that sling
attachments are secured.
During transfer, with the patient suspended in a sling attached
to the lifter, DO NOT roll caster base over uneven surfaces that
would create an imbalance of the patient lifter and could
cause the patient lifter to tip over. Uses handle on the mast at
all times to move the patient lifter.
GENERAL GUIDELINES contains important information for the
safe operation and use of this Medical Device.
SECTION 1
GENERAL GUIDELINES
Check all parts for shipping damage before using. In
case of damage, DO NOT use the equipment.
The TUFFCARE patient lifter is NOT a transport
device. It is intended to transfer a patient from
one seated surface to another (such as a bed to a
wheelchair).
DO NOT attempt to transfer, the user must be
assessed by a qualified professional. Thoroughly
read and fully understand the instructions in this
Owner’s Manual,
TUFFCARE Stand up and Transfer slings are
specifically designed to be used in conjunction with
TUFFCARE patient lifter. Slings and accessories
designed by other manufacturers are not to be
utilized as a component of Tuffcare’s patient lifter
system.
The stand up lifter is intended to be used for patient
within weight limit indicated for the lifter. DO
NOT attempt to lifter more than the weight limit
indicated.
1
2
3
4
5
WARNING

89
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
ASSEMBLING THE MAST ASSEMBLY
TO THE BASE
TUFFCARE suggests locking the rear casters ONLY when
positioning or removing the sling (stand up or transfer) from
around the patient.
TUFFCARE DOES NOT suggests locking the rear casters
of the patient lifter when lifting a patient. Doing so could
cause the
lifter to tip over and endanger the patient and assistants.
TRANSFERRING THE PATIENT
Before transferring, check that the lifter’s weight capacity
can withstand the patient’s weight.
Wheelchair wheel locks MUST be in a locked position before
lowering the patient into the wheelchair for transport.
PERFORMING MAINTENANCE
Regular maintenance of patient lifter and accessories is
required to assure proper operation.
Casters and axle bolts are also required to be checked for
tightness.
DO NOT over-tightens mounting hardware. It will cause a
damage of mounting brackets.
NOTE: See detail at Section 6 for maintenance.
PINCH POINTS
Pinch points exist at base of lifter. Use caution, otherwise
injury could occur.
SECTION 2
ASSEMBLY
The lifter comes with pre-assembled main frame for EZ assembly
1 Set base on the floor. Lock both rear casters
before lifting up the mast.
WARNING
Use only Tuffcare parts to complete this stand up patient lifter.
Use the included ranch to
secure the bolts and nuts.
Note: two longer bolts use on
side by side (upper & lower
holes), short one uses on the
middle.
Check and tighten all hardware
BEFORE use.
2 Lift up the mast to mounting
bracket on the base.
STEP DOWN TO LOCK
3
4
short
bolt
long
bolt

10 11
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
ATTACH THE HI-LOW ACTUATOR TO THE
MAST ASSEMBLY
Position the hi-low actuator
between the mast bracket.
Install the pin through the
holes of the hi-low actuator
and mast bracket and secure
with hitch pin.
1
2
Move the lift arm to align the
holes in the hi-low actuator
with the holes in the arm
bracket.
Install the pin through the
holes of the hi-low actuator
and arm bracket and secure
with hitch pin.
3
4
Place the control unit on the
mounting bracket at
the desired position.
Screw the mounting screws
through the control unit into
mounting bracket. Tighten
securely.
1
2
ATTACHING THE CONTROL UNIT ON
MOUNTING BRACKET
Lift up on the handle on the back of
battery case.
HANDLE
1
ATTACHING THE BATTERY CASE
ON CONTROL UNIT
WARNING
Make sure there is an audible click when plugging battery
case on control unit. Otherwise, injury or damage may occur.

12 13
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
PUSH
PREPARE THE PATIENT LIFT FOR USE
Plug the hand control, leg actuator (For P445 Full Electronic
Stand-up Lifter Only) and hi-low actuator into the connections
on the bottom of the control unit.
Check and tighten all hardware BEFORE use.
Control Unit
Plug for Power Cord
Plug for Hi-low Actuator
Plug for Pendant
Plug for Leg Actuator
For P445 only
1
2
Place the battery case on control unit
at the desired position.
Push the top of battery case against
mounting bracket until there is an
audible click
2
3
LOCKING/UNLOCKING THE
REAR CASTERS
RAISING/LOWERING THE
PATIENT LIFT
SECTION 3
OPERATION
WARNING
DO NOT attempt to transfer, the user must be
assessed by a qualified professional. Thoroughly
read and fully understand the instructions in this
Owner’s Manual.
LOCK
P440 P445
UNLOCK
PRESS To Raise the
Patient Lift
PRESS To Lower the
Patient Lift
Controls the
Hi-low section

14 15
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
CLOSING/OPENING THE LEGS
To Open and Close the Legs on P445
Press the open and close button on
the hand control.
To Open and Close the Legs on P440
Step down on left side of “Leg Adjusting Stepper” to
close the legs
Step down on right side of “Leg Adjusting Stepper” to
open the leg.
Leg Adjusting Stepper for P440
To reset, rotate the emergency
button clockwise.
EMERGENCY RELEASE
To activate the emergency release, push the
Red Button (powered by 9V battery) located on
the side of Hi-low actuator to lowering down
the lift arm.
Open the battery cover located at the
base of liner hi-low actuator. Insert a 9
Volt battery into and replace cover.
Note: The battery is provided the power
for emergency lowering down.
RED emergency
button on Control Unit
Red button out = Powered On
Red button pushed in = Power Off
USING THE EMERGENCY STOP
ACTIVATING A MECHANICAL
EMERGENCY RELEASE
REPLACE EMERGENCY
RELEASE BATTERY
Push the RED emergency button
in to stop the lift arms
from raising or lowering.

16 17
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
NOTE: The battery must be recharged daily to prolong
battery life.
Place the battery on the control unit for charging battery.
Push the top of the battery against the mounting bracket
until there is an audible click, See more detail on page –
(13) for Attaching the Battery Case on Control Unit.
Plug the power code into a 110 Volt outlet.
CHARGING THE BATTERY
NOTE: The charge LED will illuminate. When charged, the LED
will stop illuminating.
NOTE: It will take approximately (4) hours to charge a battery
that requires a full charge.
1
2
When the charging power cord is
plugged into an electrical outlet,
the green led light on the left of
the battery will come on. The
built-in charging system senses
a drop in battery voltage; then it
automatically increases its output
to re-charge the battery.
The bars on the battery meter will begin to flash in a running
order, indicating that the battery is charging on a fast mode “Bulk
Charge”. Fast charging usually last for 30 min. If when charging
cord is plug in and the battery meter do not indicate this suggest
faulty battery. Have the battery pack replaced.
When the battery becomes
fully charged, the battery meter
indicatorbars turn off. Unplug the
charging cord and the lifter will be
ready for use.
When the battery reserve reaches a
desirable level the battery meterstops
flashing. Now the battery meter will
indicate a full gage when all the bars
light up. At this time the charger turns
into slow charging “Absorption Charge”,
leave charging for 4 to 6 hours.

18 19
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
SECTION 4
LIFTING THE PATIENT
WARNING
DO NOT exceed the maximum weight limit of
350 lbs.
DO NOT attempt to transfer, the user must be
assessed by a qualified professional. Thoroughly
read and fully understand the instructions in this
Owner’s Manual.
ALWAYS keep hands and fingers clear of moving
parts to avoid injury.
Individuals that use the stand-up patient sling MUST
be able to support their own weight, otherwise
injury may occur.
DO NOT move the patient if the patient sling is not
properly connected to the attachment holders on
the lift arm. Check that the patient sling is properly
connected to the attachment holders BEFORE
lifting the patient.
During transfer, with the patient suspended in the
patient sling, DO NOT roll the base of the patient
lifter over any uneven surfaces that would cause the
patient lifter to become unstable.
ALWAYS use the handle on the mast assembly to
move the stand up lifter to ensure the safety.
1
2
3
4
5
6
WARNING
The legs of the stand-up lifter MUST be in the
maximum open position for stability and safety.
POSITIONING THE STAND UP LIFTER
1 Obtain stability.
Step down on right side of “Leg Adjusting Stepper” to open the
legs to the maximum open position.
Press the “FOOT” – “OPEN”
button on the hand control to
open the legs to the maximum
open position.
P425
P420
Step down on right to OPEN
Maximum Open
Position is 30”

20 21
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
2 Position the stand up lifter using the handle on the mast.
3 Press the “ LIFT” – “DOWN” button on the hand control to lower
the lift arms for easy attachment to the sling.
Lift arms
Press “DOWN” bottom to Lower Arms for
Attachment
Handles
LIFTING THE PATIENT
WARNING
DO NOT exceed the maximum weight limit
of 400 lbs.
DO NOT attempt to transfer, the user must be
assessed by a qualified professional. Thoroughly
read and fully understand the instructions in this
Owner’s Manual.
ALWAYS keep hands and fingers clear of moving
parts to avoid injury.
Individuals that use the stand-up patient sling MUST
be able to support their own weight, otherwise
injury may occur.
DO NOT move the patient if the patient sling is not
properly connected to the attachment holders on
the lift arm. Check that the patient sling is properly
connected to the attachment holders BEFORE
lifting the patient.
During transfer, with the patient suspended in the
patient sling, DO NOT roll the base of the patient
lifter over any uneven surfaces that would cause the
patient lifter to become unstable.
ALWAYS use the handle on the mast assembly to
move the stand up lifter to ensure the safety.

22 23
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
NOTE: The patient MUST be in a seated position first. Use the
head section of the bed to get the patient upright then move
legs over the side of the bed.
Instruct the patient to hold onto
the lift arms on both sides of the
patient lifter.
Instruct the patient to lean back
into the standing or transfer
sling.
ENSURE THE FOLLOWING:
1 The bottom edge of the transfer sling is at the base of the
patient’s spine.
2The rear casters are unlocked.
3 The legs are in the maximum open position.
WARNING
Standing Slings - Before lifting the patient, make
sure the bottom edge of the transfer sling is at the
base of the attachment holders and the patient’s
arms are outside the sling.
1
2
WARNING
If transferring a patient from a wheelchair, the
wheelchair wheel locks MUST be in the locked
position before lowering the patient into the
wheelchair. Otherwise, injury may occur.
4 If transferring from a
wheelchair, lock the wheel
locks on the wheelchair.
Lift arms
Handles
Legs
Caster
Press “DOWN” bottom to Lower Arms for
Attachment
Press “UP” bottom to raise the patient above the
surface (bed, wheelchair or any objects).

24 25
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
SECTION 5
TRANSFERRING THE
PATIENT
DO NOT attempt to transfer, the user must be
assessed by a qualified professional. Thoroughly
read and fully understand the instructions in this
Owner’s Manual.
DO NOT move the patient if the sling is not properly
connected to the attachment holders of the stand
up lifter. Check that the sling is properly connected
to the attachment holders prior to lifting a patient.
DO NOT use slings and stand up lifter of different
manufacturers. TUFFCARE slings are made
specifically for use with TUFFCARE stand up lifter.
Otherwise, injury or damage may occur. The legs of
the stand up lifter MUST be in the maximum open
position for optimum stability and safety.
Be sure to check the sling attachments each time
the sling is removed and replaced to ensure that it
is properly attached before the patient is removed
from a surface.
WARNING
NOTE: Tuffcare recommends that two assistants be used when
transferring a patient to a wheelchair.
TRANSFERRING TO A WHEELCHAIR
When elevated a few inches off the seating surface
of the wheelchair and before moving the patient,
check again to make sure that all hardware
and straps/chains are properly connected. If any
attachments are NOT properly in place, lower the
patient completely to correct this problem.
Adjustments for safety and comfort should be made
before moving the patient. Patient’s arms should be
inside of the chains or straps.
TUFFCARE slings and Hardware are designed
specially for use with TUFFCARE Patient Lifter. For
the safety of the patient, DO NOT intermix slings
and patient lifter of different manufacturers.
WARNING
Ensure the legs of the lifter (with patient) are in the
maximum open position.
1
Maximum Open
Position is 30”

26 27
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
Move the wheelchair into position.
Engage the rear wheel
locks of the wheelchair to
prevent movement of the
wheelchair.
WARNING
Wheelchair wheel locks MUST be in a locked position
before lowering the patient into the wheelchair for
transport.
2
3
Position the patient over
the seat with their back
against the back of the
wheelchair.
Lower the patient by
turning the control valve
counterclockwise.
4
5
The assistant behind the wheelchair pulls back on either the
handle or sides of the sling to place the patient into the back
of the wheelchair.
NOTE: Holding the handle or sides of the patient lifter maintains
a good center of balance and prevents the wheelchair from
tripping forward.
Release the sling from the patient lifter.
6
7

28 29
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
WARNING
When elevated a few inches off the seating surface
of the wheelchair and before moving the patient,
check again to make sure that all hardware
and straps/chains are properly connected. If any
attachments are NOT properly in place, lower the
patient completely to correct this problem.
Adjustments for safety and comfort should be made
before moving the patient. Patient’s arms should be
inside of the chains or straps.
TUFFCARE slings and Hardware are designed
specially for use with TUFFCARE Patient Lifter. For
the safety of the patient, DO NOT intermix slings
and patient lifter of different manufacturers.
TRANSFERRING A PATIENT TO A CAR
NOTE: Tuffcare recommends that two assistants be used when
transferring a patient from a wheelchair to a car.
NOTE: The transfer to a car should be made on a level driveway or
even surface.
NOTE: For easy transfer, make sure to shorten the distance
between the patient and the cradle. Lock the rear wheels to further prevent
movement of the wheelchair.
2
1Attach the sling straps/chains to cradle.
swivel bar
swivel bar

30 31
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
Lift the patient from the wheelchair.
Move the lifter, by the handle bar, to a
position close to the doorway of the car.
Lower the cradle of the lifter until it is
about even with the roof of the car.
As one assistant pushes the patient into
the car by his knees until the patient is
positioned over the seat of the car, the
other assistant lowers the cradle.
As the cradle is being lowered, the first
assistant is not only pushing but turning
the patient into a position that faces the
front of the car.
3
4
5
6
7
8While one assistant is holding the
patient, the other assistant removes the
straps/chains from the cradle and slides
the patient lifter out of the doorway.
first assistant
first assistant
second assistant

32 33
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
first assistant
NOTE: The sling may be left under the patient for
further transfer or removed.
second assistant
WARNING
When elevated a few inches off the seating surface
of the wheelchair and before moving the patient,
check again to make sure that all hardware
and straps/chains are properly connected. If any
attachments are NOT properly in place, lower the
patient completely to correct this problem.
Adjustments for safety and comfort should be made
before moving the patient. Patient’s arms should be
inside of the chains or straps.
TUFFCARE slings and Hardware are designed
specially for use with TUFFCARE Patient Lifter. For
the safety of the patient, DO NOT intermix slings
and patient lifter of different manufacturers.
TRANSFERRING A PATIENT FROM A
CAR TO A WHEELCHAIR
NOTE: Tuffcare recommends that two assistants be used when
transferring a patient from a car to a wheelchair.
NOTE: One assistant MUST support patient at all times.
With the first assistant supporting the patient, the second
assistant lowers the lift arm of the patient lifter until the
cradle is even with the roof of the car.
Attach the sling to the cradle.
sling
1
2
3
4
Lift the patient up off of the seat until the straps/chains
are taut.
Turn patient with sling until legs are outside of car.

34 35
RHINO STAND UP PATIENT LIFTER P440 and P445 RHINO STAND UP PATIENT LIFTER P440 and P445
LUBRICATING THE LIFT
A light grease lubricant may be applied to the ball bearing and
swivel of the casters every three months.
PERFORMING REGULAR MAINTENANCE
Regular maintenance of lift and accessories is required to ensure
proper operation. Casters and axle bolts are also required to be
checked for tightness.
CLEANING THE LIFTER
The lifter can be cleaned with non-abrasive cleaners.
DETECTING WEAR AND DAMAGE
SECTION 6
MAINTENANCE
• Check monthly that all of screws are tight
and have not loosened.
• Check monthly for cut or exposed wires on the
electrical components.
• Replace any defective parts immediately and
ensure that the lifter is not used until repairs job
is completed done.
NOTES:
SECTION 7
LIMITED WARRANTY
The warranty below has been drafted to comply with Federal Law applicable to
products manufactured after July 4, 1975. This warranty is extended only to the
original purchaser/consumer (or dealer non-consumer who does not buy for resale).
Tuffcare® warrants that it’s proprietary Institutional Beds will be free from defective
workmanship and materials for a period of three (3) years following the date of
original manufacture with the following exceptions: All welds are warranted for the
life of the bed. Electronics on the beds are warranted for one (1) year. The warranty
period commences on the original manufacture date. If within such warranty period
any such product proven to Tuffcare® satisfaction to be defective, such product will
be repaired or replaced at Tuffcare® option.
Tuffcare® sole obligation and your exclusive remedy under this warranty shall be
limited to such repair and/or replacement. This warranty does not include any labor
charges incurred in replacement parts installation. Freight charges to the factory are
at the expense of the consumer or seller. Return freight charges will be prepaid by
Tuffcare®. For warranty service, please contact the authorized dealer from whom you
purchased your Tuffcare® products. In the event that you do not receive satisfactory
warranty service, please write directly to Tuffcare®: 4977 La Palma Ave, Anaheim,
California, 92807. DO NOT RETURN PRODUCTS WITHOUT PRIOR AUTHORIZATION.
LIMITATIONS AND EXCLUSIONS: The foregoing warranty shall not apply to products
subjected to negligence, abuse, misuse, improper operation, improper maintenance,
improper storage or damages beyond Tuffcare® control. The evaluation will be solely
determined by Tuffcare®. The warranty shall not apply to problems arising from
normal wear, or failure to follow instructions, or if parts are not manufactured by
Tuffcare®, or do not comply with original equipment specifications that are added
to Tuffcare® product.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND SHALL NOT
EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN.
TUFFCARE® SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER.
This warranty gives you specific rights and you may also have other legal rights which
vary from state to state. Some states do not allow the exclusion or limitations of
incidental or consequential damage, or limitation on how long an implied warranty
lasts, therefore, the above exclusion and limitation may not apply to you.
Lift up on legs with one hand and tilt the patient back with
other hand.
The second assistant should pull the patient lifter away
from the car until the patient is completely clear of the
door frame. Release the patient back to a normal sitting
position in the sling and place patient in wheelchair.
5
6

WHEELCHAIRS • WALKING AIDS • MATTRESSES & SUPPORTS
POWER CHAIRS • SCOOTERS • HOME CARE BEDS • LIFTERS
VISIT WWW.TUFFCARE.COM FOR OTHER PRODUCTS
WEST COAST DIVISION
4977 E. La Palma Ave
Anaheim, CA 92807
EAST COAST DIVISION
1290 S. W. 30th Ave
Pompano Beach, FL 33069