MODEL: 18WM30602/ 18II332FGL
OPERATING INSTRUCTIONS
Go to tsicustomerservice.com for product warranty registration
Remote
IMPORTANT INSTRUCTIONS
1. The battery compartment is located on the back end of the remote
control.
2. Press and slide the battery door open and remove the old battery.
3. Insert 2 AAA batteries, checking that the + and - sides of the battery
match inside the battery compartment.
4. Replace the battery compartment door.
Caution:
• For best results, use 2pcs AAA alkaline batteries.
• Install only new batteries of the same type in your product.
• Failure to insert batteries in the correct polarity, as indicated in the
battery compartment, may shorten the life of the batteries or cause
batteries to leak.
• Do not mix old and new batteries.
• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel
Cadmium) or (Nickel Metal Hydride) batteries.
• Danger of explosion if battery is incorrectly replaced.
• Do not ingest batteries.
• Batteries should be recycled or disposed of as per state and local
guidelines.
DISPOSAL OF USED BATTERIES
Battery may contain hazardous substances which could endanger the
enviroment and human health. Used batteries shall not be treated as
municipal waste, but left at the appropriate collection point for recycling.
For more information about collection and recycling of used batteries,
please contact your local municipality or waste disposal service.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons including the following:
1. Read all instructions before using this appliance.
2. DANGER – High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of this heater.
WARNING: In order to avoid overheating, do not cover the heater.
3. CAUTION: Never leave the heater operating unattended. Extreme caution is necessary if unsupervised children or invalids are nearby.
4. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
5. Always unplug this appliance when not in use.
6. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, or if it has been dropped or damaged in any manner.
7. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid a hazard.
8. Do not use outdoors.
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appliance where it may fall into a bathtub or
other water container.
10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from trafc area and where it will not be tripped over.
11. To disconnect this appliance, turn controls to the off position, then remove plug from outlet.
12. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or re, or damage the appliance.
13. This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1
Canadian Electrical Code or for U.S.A. installations, follow local codes and the National Electrical Code, ANSI/NFPA NO.70.
14. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or re, or damage the appliance.
15. To prevent a possible re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where opening may become blocked.
16. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or ammable liquids are used or stored.
This stove should not be used as a drying rack for clothing. Christmas stockings or decorations should not be hung in the area of it.
17. Use this appliance only as described in the manual. Any other use not recommended by the manufacturer may cause re, electric shock or injury to persons.
18. This product is equipped with a polarized plug (one blade is wider than the other blade). To reduce the risk of electrical shock, this plug will t into a
polarized outlet only one way. This is a safety feature. Avoid the use of an extension cord because of the risk of overheating the cord and the risk of re.
Extension cords are for temporary use only. If an extension cord must be used, it must be UL/CSA certied, rated at 15A (1875W),125V maximum
with14AWG minimum and constructed of two current carrying conductors with ground. A heavy duty extension cord with the
shortest length possible for the connection is recommended and must not be longer than 50 ft. (15.2m ). Do not coil or cover
the extension cord. Caution: To prevent electric shock, match wide blade of plug to wide slot and fully insert.
Note:
Battery disposal
Please always dispose of batteries
at a suitable recycling point.
AAA 1.5V
AAA 1.5V
1
23
Warning: You must install the
tip restraint hardware to help
prevent any accidents or
damage to the unit. We strongly
recommend attaching the tip
restraint hardware to a wall
stud and your unit. For all other
wall types, please visit your
local hardware store to obtain
the proper hardware.
Wall Stud
Poteau Mural
Montante De
Madera
© 2019, Twin-Star International,Inc.
VOLTAGE 120 VAC, 60 Hz
AMPS 12.5 Amps
WATTS 1500 Watts
PRODUCT SPECIFICATIONS
Manufactured and distributed by Twin-Star International, Inc.,
under license from Duraflame, Inc. duraflame, the flame symbol
and logo are registered trademarks of Duraflame, Inc.
Twin-Star International, Inc.
Delray Beach, FL 33445
Note: When rst running the heater there may be an odor.
This is normal as the heater has a surface coating on the
internal parts. For the rst several hours of operation, the
coating reacts with the internal parts to permanently protect
them. The odor is safe; if you are sensitive to the odor, it is
recommended to run the heater in a well-ventilated area until
the odor dissipates.
Warning: This is an unvented, electric
appliance. DO NOT attempt to burn wood
or manufactured relogs in or on this
appliance or grate.
--TIMER
-- FLAME
-- HEATER
Pressing the timer button will cycle through the timer
settings: 30 minutes, 1 Hour, 2H, 3H, 4H, 5H, 6H, 7H, 8H,
9H and off (00).
1. There are 5 brightness levels that can be selected.
2. Settings F5 - F1 decrease in brightness.
3. Pressing and holding the ame button for 3 seconds will enter the
control into the LED cabinet light settings. There are 4 brightness levels
and OFF setting that can be selected. Settings 1-4 decrease the LED
brightness.
4. After 3 seconds without control input, the display will exit the LED
cabinet light setting and show the replace ame setting.
1. The replace contains three infrared quartz heating
elements.
2. The thermostat setting range is 62°F - 82°F (17°C - 27°C)
or continuously ON. Set the heater to (00) to use the ame
effects without the heat.
3. The thermostat is adjustable by 2°F or 1°C increments.
4. The up and down buttons “ ” on the remote will
increase / decrease temperature setting.
5. To change between °F and °C, press and hold the HEATER
button on the control panel for 3 seconds.
For Customer Service:
tsicustomerservice.com
(+1) 888-674-7517
8:30 a.m.-5:30 p.m., EST, Monday-Friday
OPERATING INSTRUCTIONS
-- POWER
1. The power button supplies power to all of the replace functions. The
power button will put the lantern in a standby mode. This will turn
off all functions at once, but will hold the settings in the memory. By
pressing the Power button again, the unit will turn on with the retained
settings.
2. With the power on, press and hold the Power button on the control
panel for 10 seconds to disable or re-enable the heater function. Once
disabled or re-enabled, the candle lights will ash multiple times.
3. Before the heater powers off, the fan will continue to run for a period of
time to cool down the internal parts.
MODEL: 18WM30048 / 18II332FGL-L
Pressing the light button on the remote control will cycle the
LED cabinet lights through the different brightness
settings; 1, 2, 3, 4 and OFF. Settings 1-4 will decrease the
LED brightness.
--LIGHT
B077
Control Panel
Display
