Tyco BLAZEMASTER CPVC User manual

BLAZEMASTER
CPVC Fire Sprinkler Pipe & Fittings
Submittal Sheet
Page 1 of 2 AUGUST 2018 TFP1915
Worldwide
Contacts
www.tyco-fire.com
IMPORTANT
Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.
General
Description
TYCO CPVC Pipe and Fittings pro-
duced by Johnson Controls are
designed exclusively for use in wet
pipe automatic fire sprinkler systems.
The TYCO CPVC Pipe and Fittings are
produced from BLAZEMASTER CPVC
compound that is a specially developed
thermoplastic compound composed
of post chlorinated polyvinyl chloride
(CPVC) resin and state of the art addi-
tives. TYCO CPVC Pipe and Fittings are
easier to install than traditional steel
pipe systems, and at the same time,
provide superior heat resistance and
strength as compared to traditional
CPVC and PVC piping materials used
in the plumbing trade. Various adapt-
ers are available to connect CPVC
pipe to metallic piping. All female pipe
thread adapters have brass inserts for
durability. Grooved adapters connect
directly to grooved end valves and
metallic pipe, with flexible grooved end
couplings.
NOTICE
The CPVC Pipe and Fittings produced
with BLAZEMASTER CPVC compound
described herein must be installed
and maintained in compliance with
this document and with the applica-
ble standards of the NATIONAL FIRE
PROTECTION ASSOCIATION (NFPA),
in addition to the standards of any
authorities having jurisdiction. Failure
to do so may impair the performance
of these devices.
The owner is responsible for main-
taining their fire protection system
and devices in proper operating con-
dition. Contact the installing contrac-
tor or product manufacturer with any
questions.
Technical
Data
Sizes
3/4 Inch to 3 Inch
Maximum Working Pressure
175 psi
Approvals
UL and C-UL Listed
FM Approved
LPCB Approved
NSF Certified
MEA Approved
(Refer to Installation Handbook IH-1900
dated April 2016 for exact listing/approval
information.)
Manufacture Source
U.S.A.
Material
Pipe:
ASTM F442, SDR 13.5
Fittings:
ASTM F438 (Sch. 40)
ASTM F439 (Sch. 80)
ASTM F1970
Color
Orange
Installation
TYCO CPVC Pipe and Fittings are to
be to be installed in accordance with
Installation Handbook IH-1900.

TFP1915
Page 2 of 2
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
BLAZEMASTER is a trademark of The Lubrizol Corporation
1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone [phone]
© 2018 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Care and
Maintenance
TYCO CPVC Pipe and Fittings are to be
maintained and serviced in accordance
with this section.
Before closing a fire protection system
control valve for inspection or main-
tenance work on the fire protection
system that it controls, permission to
shut down the affected fire protection
system must first be obtained from
the proper authorities and all person-
nel who may be affected by this action
must be notified.
After placing a fire protection system
in service, notify the proper authorities
and advise those responsible for moni-
toring proprietary and/or central station
alarms.
The owner is responsible for the inspec-
tion, testing, and maintenance of their
fire protection system and de-vices in
compliance with this document, as well
as with the applicable standards of the
NATIONAL FIRE PROTECTION ASSO-
CIATION (e.g., NFPA 25), in addition to
the standards of any authority having
jurisdiction. Contact the installing con-
tractor or product manufacturer with
any questions.
Automatic sprinkler systems should be
inspected, tested, and maintained by a
qualified Inspection Service in accor-
dance with local requirements and/or
national codes.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.