Tyco Bentel security powerg bw-sro User manual

D-308696 BW-SRO Installation Guide 1

1. INTRODUCTION

The BW-SRO is a fully wireless outdoor siren, designed for installation

in areas in which wiring action is difficult or impossible.

The siren is compatible with PowerG control panels.

Note: Operations described in these instructions applies to BW control

panels. For further information related to operations with a different

control panel, refer to the control panel's instructions.

Features

lSiren and strobe light activation: When an identified event

message is received from the compatible PowerG alarm system,

the siren activates its sounder & strobe light.

Notes:

The sounder is activated for a predefined "Bell Time" (refer to the

control panel Installer Guide), according to local authorities

requirements, or until the system is disarmed, whichever occurs

first.

The strobe light operates as described in the PowerG Installer

Guide.

lTamper indication: In case of tamper while the system is armed,

the siren transmits the message to the alarm system and then the

alarm system determines whether the siren should be activated or

not. If the siren does not receive an acknowledge message from the

alarm system, the siren will function independently.

lLow battery voltage alert: When the battery voltage is low, a low

battery message is sent to the alarm system. After the low voltage

message delivery, at least 2 siren alarms are possible before the

siren is totally inactive.

lPower Supply: Non-rechargeable battery.

lSound Types: Burglar (between 1400 Hz - 3200 Hz), fire, gas

(CO) and flood.

lEntry/Exit: Exit delay beeps sound once the user has armed the

system. Entry delay beeps sound once the user has entered the

protected area. (Entry/exit beeps can be enabled / disabled from

the control panel Installer menu.)

lSquawk indications: Squawk (beep) sounds can be used to

indicate alarm system arming (1 squawk) and disarming (2

squawks) by a keyfob (squawk can be enabled from the control

panel User menu).

lFreezer trouble beeps: If a freezer trouble zone reports a trouble,

such as a change in temperature, freezer trouble beeps occur every

minute for indoor or outdoor sirens. You can turn on or turn off

freezer trouble beeps in the control panel Installer menu.

lStrobe Light Color: The siren can be purchased with blue lens.

lSiren activity LED: A flashing LED (optional, at the bottom of the

siren front panel) indicates siren activity (can be disabled by the control

panel)

lDouble Tamper protection: When the siren front panel is removed

or when the siren is removed from the wall, tamper alarm is sent to the

alarm system.

Important! The BW- SRO siren must be installed on the wall in a

vertical position with the screw pointing to the floor only, as illustrated

in Figure 1b. The importance of correct positioning of the BW-SRO is

to enable the siren to function as a waterproof device.

l2-way full supervision

The siren is fully supervised, 2-way communication device. It includes

a receiver, to receive event messages from the alarm system, and a

transmitter, to periodically transmit its status signal to the alarm

system.

A. BW-SRO can be recognized

outwardly by its red screw cap.

Fig. 1a External View

B. Wall

Fig. 1b Mounting Position

Self-test feature

Upon pressing the self test switch, siren functional check is performed -

low level sounds and flash light indicate that the siren is serviceable.

Installation Guide

BW-SRO

Fully Wireless PowerG Outdoor Siren

2. INSTALLATION

2.1. Installation

1. Open plastic cover screw.

2. Using Philips screwdriver, remove screw and remove cover.

3. Optional step: Hang back unit with a screw on mounting surface to

make the next step (drilling marking) easier.

4. Mark for drilling.

5. Drill 5 holes.

6. Fasten with 5 screws.

7. Release catch (A) and open battery cover (B).

8. Connect the two connectors in their respective sockets.

9. Insert the battery and connect the battery connector.

A. Mounting surface.

B. For tamper.

C. Self-Test button.

D. Enroll button.

E. Primary battery.

F. Battery connector.

Caution! Risk of explosion if battery is replaced by an incorrect type.

Dispose of used battery according to manufacturer's instructions.

Figure 2: Installation

D-308696 BW-SRO Installation Guide 2

2.2. Enrollment

Refer to the BW panel's Installer's Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu. A general description

of the procedure is provided in the following flow chart.

Step 1 Step 2 Step 3 Step 4 Step 5

Enter the Installer menu

and select

“02:ZONES/DEVICES”

Select "ADD NEW

DEVICE" See Note 1

Enroll the device or enter

the device ID

Select the desired siren

number for the new siren

Configure Location and

Zone Type Parameters

02:ZONES/DEVICES ðADD NEW DEVICES.

MODIFY DEVICES

ðENROLL NOW or

ENTR ID:XXX-XXXX

ðSR1:Siren Outdoor

ID No.410-XXXX

ðSR1.LOCATION

SR1.ZONE TYPE

SR1.SET CHIME

Step 6 Step 7 Step 8 Notes:

Enter PARTITIONS.

See Note 2

Assign partitions to the siren

by pressing the ,

and buttons

on the panel

Select the "DEV

SETTINGS" option and

refer to the section below to

configure the siren

parameters.

1. If the siren is already enrolled, you can

configure the siren parameters and assign

partitions via the “Modify Devices”

option – see Step 2.

2. PARTITIONS will appear only if

PARTITIONING was previously enabled in

a panel that supports the Partitioning

feature (for further details, see

"Partitioning" in the BW Installer Guide).

3. When there is an alarm, the siren will

sound regardless of partition assignment.

SR1.PARTITIONS ðSR1:P1n-- P2....P3nðSR1:DEV SETTINGS ð

ðmeans scroll ww and select OK

2.3. Configuring the Siren Parameters

Enter the DEVICE SETTINGS menu and follow the configuration instructions for the BW-SRO outdoor siren as described in the following table.

Option Configuration Instructions

STROBE ALARM Here you determine whether or not to activate the strobe alarm, and if activated, whether to activate the strobe until the alarm

system is disarmed, or, for the programmed period of time (see "Siren Configuration" section in the control panel Installer

Guide).

Optional settings: Timer limited (default), Disabled and Until Disarmed

EXIT-ENTRY Beeps Here you determine whether or not to activate the exit – entry beeps, and if enabled, whether to activate in HOME or AWAY

mode.

Optional settings: Disabled (default), Disabled & Home and Enabled.

SQUAWK Here you determine whether or not to enable the squawk, and if enabled, whether to activate the sounder only, or, the

sounder and strobe simultaneously.

Optional settings: Disabled (default), Sounder only,Strobe only and Sounder+strobe.

SOUNDER

VOLUME

Here you determine the volume level of the sounder.

Optional settings: Volume HIGH(default), Volume LOW and Volume MID.

ACTIVITY LED Here you determine whether or not the LED will be activated to indicate that the siren is operating.

Optional settings: Disabled (default) and Enabled.

AUTO TAMPER

ALRM

Here you determine whether or not the siren alone will sound a tamper alarm when there is no communication between the

siren and the control panel.

Optional settings: Disabled (default) and Enabled.

FRZR TRBL BEEP Turn on or turn off freezer trouble beeps for indoor or outdoor sirens. Freezer trouble beeps occur every minute.

Optional settings: on (default) and off.

D-308696 BW-SRO Installation Guide 3

2.4. Local Diagnostics Test

Before testing, remove the plastic cover and then open the battery cover

(see "Figure 2: Installation" on page 2).

A. Press the self-test button once and release it; the following

procedure should occur in turn:

The red LED will switch ON and then OFF, the green LED will switch

ON and then OFF, the strobe light will switch ON and then OFF and

the piezo siren will sound to indicate that the siren is now fully

operational.

B. After 2 seconds the LED blinks 3 times.

The following table indicates received signal strength indication.

LED response Reception

Green LED blinks Strong

Orange LED blinks Good

Red LED blinks Poor

No blinks No communication

Important! Reliable reception must be assured. Therefore, "poor"

signal strength is not acceptable. If you receive a "poor" signal from the

detector, re-locate it and re-test until a "good" or "strong" signal strength

is received.

Note: For detailed Diagnostics Test instructions refer to the control

panel Installer Guide.

3. Compliance With Standards

The BW-SRO complies with the following standards:

Europe: EN 300 220, EN 301489, EN 50130-4, EN 62368-1, EN 50130-5, EN 50131-4 self-powered siren, type W, EN 50131-5-3. IP55.

Hereby, Bentel Security S.r.l. declares that the radio equipment type BW-SRO is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

www.bentelsecurity.com/dc.

Certified by Applica Test & Certification AS in accordance with EN 50131-4, EN 50130-4, EN 50130-5. Security Grade 2 and Environmental

Class IV.

EN 50131-1 Security Grade: According to EN 50131-1 this equipment can be applied in installed systems up to and including Security

Grade 2.

EN 50131-1 Environmental Class: Class IV

UK: This product is suitable for use in systems installed to conform to PD6662 at Grade 2 and environmental class 4. BS8243.

Warning! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then

you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.

Directive 2012/19/EC Waste Electrical and Electronic Equipment.

4. SPECIFICATIONS

Frequency Band (MHz): 868

Maximum Tx Power: 14 dBm @ 868 MHz

Modulation: GFSK

Antenna: Built-in antenna

Communication Protocol: PowerG

Supervision interval: Signaling at 128 s intervals

Current consumption:

Quiescent mode: 50μA

Alarm sound operated: 430mA

Siren Type:piezo, 1.4-3.2 kHz, sweep frequency 7 Hz

Sound Level: minimum 100 dBA @ 1 m

Power Supply: Type C

Battery Type: Four 3.6V/3.5Ah Lithium independent cells (EVE and

FANSO ER18505M) assembled in two plastic wrappings and connected

to the cable adaptor (see Figure 2). Bentel assembly catalog no.

PFNBTBLIBW-B35SR.

Note: Use only the above battery.

Note: The strobe flashes 5 times and the red LED lights continuously

during first battery installation.

Battery Life Expectancy: 8 years (for typical use)

Low Battery Threshold: 2 V +300 mV negative slope OR 1.2 V

Strobe Light: Pulsed @ 1 sec.

Operating Temperature: -33°C to 70°C (-27.4°F to 158°F)

RH humidity: 93%

Dimensions (LxWxD): 295x186x63mm (11-5/8 x 7-5/16 x 2-1/2 in)

Weight (including battery): 970g (34 oz)

Color: White (with blue lens)

WARRANTY

Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”) against defective

workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer.

This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated under conditions of normal use in

accordance with the Manufacturers recommended installation and operation instructions. Products which have become defective for any other reason,

according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operational instructions, neglect,

willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by

this Warranty.

There is absolutely no warranty on software, and all software products are sold as a user license under the terms of the software license agreement

included with such Product.

D-308696 BW-SRO Installation Guide 4

The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product will prevent any death and/or

personal injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate

warning or protection. The Product, properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee or

insurance that such events will not occur.

Conditions to Void Warranty: This warranty applies only to defects in parts and workmanship relating to normal use of the Products. It does not

cover:

* damage incurred in shipping or handling;

* damage caused by disaster such as fire, flood, wind, earthquake or lightning;

* damage due to causes beyond the control of the Seller such as excessive voltage, mechanical shock or water damage;

* damage caused by unauthorized attachment, alterations, modifications or foreign objects being used with or in conjunction with the Products;

* damage caused by peripherals (unless such peripherals were supplied by the Seller;

* defects caused by failure to provide a suitable installation environment for the products;

* damage caused by use of the Products for purposes other than those for which they were designed;

* damage from improper maintenance;

* damage arising out of any other abuse, mishandling or improper application of the Products.

Items Not Covered by Warranty: In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost

to the repair centre; (ii) customs fees, taxes, or VAT that may be due; (iii) Products which are not identified with the Seller's product label and lot number

or serial number; (iv) Products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing

to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at the Seller's option.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES, WHETHER

WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR

INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID.

THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE

DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR

INDIRECTLY ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER

PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO

PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT

THE PRODUCT FAILED TO FUNCTION. HOWEVER, IF THE MANUFACTURER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY,

FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL

NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT INVOLVED, WHICH SHALL BE FIXED AS LIQUIDATED DAMAGES

AND NOT AS A PENALTY, AND SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST THE MANUFACTURER. SOME

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THESE

LIMITATIONS MAY NOT APPLY UNDER CERTAIN CIRCUMSTANCES.

When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed

of.

The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any telecommunication or electronic

equipment or any programs.

The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer’s discretion any Product or part

thereof that may prove defective. Any repair and/or replacement shall not extend the original Warranty period. The Manufacturer shall not be

responsible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and

insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty.

This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification,

variation or extension of this warranty. This warranty shall apply to the Product only. All products, accessories or attachments of others used in

conjunction with the Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any

damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the malfunction of the Product due to

products, accessories, or attachments of others, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original

Purchaser and is not assignable.

This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is contrary to the Law in the state or country were

the Product is supplied shall not apply.

Governing Law: This disclaimer of warranties and limited warranty are governed by the domestic laws of Israel.

Warning

The user must follow the Manufacturer’s installation and operational instructions including testing the Product and its whole system at least once a week

and to take all necessary precautions for his/her safety and the protection of his/her property.

* In case of a conflict, contradiction or interpretation between the English version of the warranty and other versions, the English version shall prevail.

D-308696 BW-SRO Installation Guide 5