Tyco Vigilant MX1-Au Manual

Vigilant MX1-Au
Fire Alarm System
Wiring
Diagrams
LT0442
Issue 1.96
Vigilant MX1
Sample MX1 Fire Alarm System
MX1 V1.60 AS 7240.2 05:04:07
Normal 02/02/15

Page ii 8 February 2019 LT0442 Issue 1.96
Cautions & Warnings
100V a.c. audio line wiring is defined as LV
Telecommunications circuits and is subject to the
Australian Standard AS/ACIF S009:2006.
Ensure that this wiring is appropriately separated
and insulated from LV power wiring, ELV and
other customer cabling such as detection and
control circuits.
The internal circuit cards may be damaged by
static electricity when handled. Ensure you are
wearing an earthed ESD strap when installing
the MX1 circuit cards.
Ensure all power is turned off when connecting/
disconnecting internal and field wiring as damage
may occur if wrong or partial connections are
made with power applied.
Document 29 July 2009 Issue 1.12 Sheet 123 updated
History: 10 Nov 2009 Issue 1.13 Sheet 147 updated
1 Feb 2011 Issue 1.20 Multi-MX loop changes.
Sheets 130, 148, 149 & 1982-88 added. Sheets 103, 116, 121, 124,128,
140-144 revised. Sheet 146 deleted
13 June 2011 Issue 1.30 Sheet 149 updated
16 Nov 2011 Issue 1.40 Sheets 128, 143, 145, 148 amended
30 May 2012 Issue 1.50 Sheet 147 and Drawing 1982-88 updated
4 Oct 2013 Issue 1.60 Updated for networking and 8U cabinet.
5 Nov 2013 Issue 1.70 Sheets 153 and 157 amended.
11 April 2014 Issue 1.80 Sheets 150 amended.
9 March 2015 Issue 1.90 Sheet 143 amended, Sheets 132, 161 to 165 added.
11 Nov 2015 Issue 1.91 Sheet 1982-210 Sheet 2 added.
30 March 2016 Issue 1.92 Sheet 1982-210 Sheet 2 updated.
19 July 2017 Issue 1.93 Sht 166, 167, 168 added.
21 November 2017 Issue 1.94 Shts 133, 134, 135 & 169 added, 115 & 152 updated. 1982-88 updated.
16 October 2018 Issue 1.95 Shts 136, 137 & 138 added, 134, 161, 163 & 169 updated.
8 February 2019 Issue 1.96 Sht 118 updated, 170 added.

LT0442 Issue 1.96 8 February 2019 Page iii
General
Each of these diagrams (most in the 1982-71 series) shows the wiring for a particular module, card or base
which can be used with the MX1-Au fire alarm system.
Drawing
Index
Sheet
Title
Revision
Bases
101
Not yet published
-
102
4B/5B Base
B
103
4BI/5BI Isolator Base
C
104
814RB Relay Base
A
105
4B-C Continuity Base
A
106
802SB/901SB Sounder Base
A
168
D51MX Duct Sampling Unit (with 4B-C)
A
Modules
107
DIM800 Detector Interface Module
A
108
MIM800 Mini Input Module
A
109
CIM800 Contact Input Module
A
110
MIO800 Multi I/O Module
A
111
SNM800 Sounder Notification Module
A
112
RIM800 Relay Interface Module
A
113
LPS800 Loop Powered Sounder Module
A
114
VLC800MX Vesda LaserCompact Interface
A
115
CP820/830 and MCP820/830 Call Point
B
116
LIM800 Loop Isolator Module
B
117
S271f+ Flame Detector
A
118
Intrinsically Safe Devices
B
119
VIO800 (MIO800) LaserPlus/Scanner
A
161
QIO850 Quad I/O Module
B
162
QMO850 Monitored Output Module
A
163
QRM850 Quad Relay Module
B
164
DDM800 Dual Detector Module, Loop Powered
A
165
DDM800 Dual Detector Module, Externally Powered
A
166
SIO800 Single Input/Output Module
A
167
FV400 Series Flame-Proof Detector
A
170
FV421i Intrinsically Safe Detector
A
Ancillary Devices
120
AAM2 Module
A
121
40020 External Alarm Strobe
B
122
Mini-Gen to MX1 Anc 3
A
123
T-Gen 50 to MX1 Anc 1
B
124
ISO8201 Strobe Driver to MX1 Anc 3
B
125
16 Way Protected Inputs
A
126
16 Way Relay or Open Collector O/Ps
A
127
QE90 “RZDU” I/F
A
128
MX1 Loop Card
C
129
MIM801 Mini Input Module (NZ use)
A
130
Remote FBP
C
131
PA0915 Fuse Board
A
132
AS1668 Fan Controls
A
133
T-Gen 60 to MX1 Anc 1
A
134
Single T-Gen 60/120 to 100V Switching Module
B
135
T-Gen 60/120 to 100V Splitter Module
A
136
High Level Interface (HLI) Module
A
137
Dual T-Gen 60/120 to 100V Switching Module
A
138
Triple T-Gen 60/120 to 100V Switching Module
A
15U Gearplate Layouts
140
T-Gen 60, MX Modules, MX Loop Card
B
141
Mini-Gen, Strobe Driver
C
142
16 Input, 16 Output, MX Loop Card
B

Page iv 8 February 2019 LT0442 Issue 1.96
143
16 Way Relay Board, MX Loop Cards (Bracket Mounted)
D
144
PIB IP Networking Equipment
C
148
General Purpose SGD, RS485 Board, Fuse Board
C
149
I-Hub / Fibre Modems
C
169
T-Gen 60, 100V Switching/Splitter Modules
B
Networking
150
I-Hub RS485 / Fibre Ring Network
B
151
IP Networking Wiring Details
A
8U Gearplate Layouts
152
T-GEN 60, MX Modules
B
153
SGD, Mini-Gen / Strobe
B
154
MIO800, Future Gas Card
A
155
General Purpose Relay
A
156
MX Loop Card
A
157
STP Bracket, Loop Card Bracket, MX Module Bracket
B
158
FP1012, Moxa & Ethernet Extender
A
159
FP1013, Moxa & Ethernet Extender
A
160
I-HUB / Fibre Optic Modems
A
Brigade Kits
145
MX1 WA ASE Wiring
B
147
MX1 Centaur & Centaur II ASE Mounting & FAS Wiring Details
C
1982-210-2
MX1 NTFAST Brigade I/F Wiring Details
B
Extra Information
1982-88
MX1 Zone LED Board Cabling
D
1922-98
Centaur Resistor Colour Code
A
© 2019. Johnson Controls. All rights reserved. All specifications and other information shown were current as of document
revision date and are subject to change without notice.

AR
+~--------------------------------~-~--------------------------------+-~
MX1
AL
48/58
CONFIDENTIAL· THIS DOCUMENT MUST NOT BE COPIED NOR THE CONTENTS PASSED
• ON TO IW'f THIRO PARTY WITHOUT THE CONSENT OF THE COMPIW'f.
ECO
B 4B B!SE ADDED.
DRN
I<JS
I<JS
+
FIRE
ALARM
0
CONCEALED
SPACE
BASE
UNLESS OTHERWISE STArED
, ALL DIMENSIONS IN MIUUMETRES. DO NOT SCALE. TOLERANCES ARE TO BE:
• 1 DECIMAL PLACE ±0.5, 2 DECIMAL PLACES ±0.3, 3 DECIMAL PLACES ±0.1
OICD AliTH AFVD DAlE
"tqco
MX1
RAC RAC DSCP ~
48/58 BASE
JP RC DP 4-1D-13
Fire Protection Products WIRING DIAGRAM
TYCO FIRE PROTECTION PRODUCTS
17 MARY MULLER DRIVE
DRAWING No:
1982-71
SHEET 102of
P.O. BOX 19545
CHRISTCHURCH, PH: [phone] A3
ISS/REV B
PART No:
NEW ZEALAND. FAX:[phone]
N

r
-~--------------------------------~-~-------------------------------------,
i--:--~
AR
+
-~--------------------------------~
MX1
-~--------------------~
AL
+~--------------~
+
NOTES:
1. PROVIDES MX LOOP SHORT CIRCUIT ISOLATION.
2. MAX IB UNITS BETWEEN ISOLATORS = 1 DO IB UNITS.
3. FOR PA1 011 MX1 CONTROLLER AND REV 1-2 MX1 LOOP CARDS FIT LIM800 OR
MX DEVICE WITH INTEGRAL SCI AT MX1 AL+/AL- AND AR+/AR- TERMINALS INSIDE
THE MX1 CABINET OR AN IMMEDIATELY ADJACENT BOX. NOT REQUIRED FOR
PA 1 081 OR REV 3 ONWARDS LOOP CARDS.
4. NO MORE THAN 40 DEVICES (MX DETECTORS/MODULES + ACTUATING DEVICES ON
CIM/DIM/MIM/MIO INPUTS AND EACH SEPARATE OUTPUT FUNCTION ON MIO AND
EACH SNM AND RIM MODULE) BETWEEN ISOLATORS. 850 DETECTORS IN 4B-C AND
MX DETECTORS IN ISOLATOR BASES ARE ISOLATORS.
FIRE
ALARM
0
IN CONCEALED
SPACE
TYCO E500MK2
t<t.MU 1 t. INDICATOR
CONFIDENTIAL· THIS DOCUMENT MUST NOT BE COPIED NOR THE CONTENTS PASSED
• ON TO IWY THIRO PARTY WITHOUT THE CONSENT OF THE COMPIWY.
UNLESS OTHERWISE STArED
ALL DIMENSIONS IN MIWMETRES. DO NOT SCALE. TOLERANCES ARE TO BE:
: 1 DECIMAL PLACE ±0.5, 2 DECIMAL PLACES ±0.3, 3 DECIMAL PLACES ±0.1
3nl ANGLE --6--,......,-
PROJECTION ~ ';:;:;J ~
ISS/RE.V AIIEIIliiENIS ECO DRN OICD AliTH AFVD DAlE
"tqco
MX1
A -- I<JS RAC RAC DSCP ~
48-1/58-1 ISOLATOR BASE
B N01E J UPM1ED. 4167 I<JS I.SC RC DP
13-11-10
Fire ProtectionProducts
c 48-1 IMSE IOOED.
-
I<JS JG RC DP 8-6-13 WIRING
DIAGRAM
TYCO FIRE PROTECTION PRODUCTS
17 MARY MULLER DRIVE
DRAWING No:
1982-71
SHEET 103of
N
P.O. BOX 19545
CHRISTCHURCH, PH: [phone]
A3 I ISS/REV c I
PART No:
NEWZEALAND. FAX:[phone]

TYCO SAFETY PRODUCTS
NEW ZEALAND.
Safety
Products
[phone]
[phone]PH:
17 MARY MULLER DRIVE
P.O. BOX 19545
FAX:
tyco
CHRISTCHURCH,
MX1
814RB RELAY BASE
WIRING DIAGRAM
A3 104 N1982-71 A

r
-~--------------------------------~-~-------------------------------------,
i--:--~
AR +
-~--------------------------------~
MX1
-~-------.
AL
+~-------+------~
48-C
+
NOTES:
1. USE ONLY 850XX DETECTORS.
2. PROVIDES MX LOOP SHORT CIRCUIT ISOLATION.
3. MAX IB UNITS BElWEEN ISOLATORS = 1 00 IB UNITS.
4. FOR PA1 011 MX1 CONTROLLER AND REV 1-2 MX1 LOOP CARDS FIT LIM800 OR
MX DEVICE WITH INTEGRAL SCI AT MX1 AL+/AL- AND AR+/AR- TERMINALS INSIDE
THE MX1 CABINET OR AN IMMEDIATELY ADJACENT BOX. NOT REQUIRED FOR
PA 1081 OR REV 3 ONWARDS LOOP CARDS.
5. NO MORE THAN 40 DEVICES {MX DETECTORS/MODULES + ACTUATING DEVICES ON
CIM/DIM/MIM/MIO INPUTS AND EACH SEPARATE OUTPUT FUNCTION ON MIO AND
EACH SNM AND RIM MODULE) BElWEEN ISOLATORS. 850 DETECTORS IN 48-C AND
MX DETECTORS IN ISOLATOR BASES ARE ISOLATORS.
FIRE
ALARM
0
IN CONCEALED
SPACE
TYCO E500MK2
t<t.MU 1 t. INDICATOR
CONFIDENTIAL· THIS DOCUMENT MUST NOT BE COPIED NOR THE CONTENTS PASSED
• ON TO IWY THIRD PARTY WITHOUT THE CONSENT OF THE COMPIWY.
UNLESS OTHERWISE STArED
ALL DIMENSIONS IN MIWMETRES. DO NOT SC.II..E. TOLERANCES ARE TO BE:
: 1 DECIMAL PLACE ±0.5, 2 DECIMAL PLACES ±0.3, 3 DECIMAL PLACES ±0.1
3nl ANGLE --6--,......,-
PROJECTION ~ ';:::;J ~
ISS/RE.V AIIEIIliiENIS
ECO DRN OICD AliTH AFVD DAlE
"tqco
MX1
-
I<JS JG RC DP 6-6-13 48-C CONTINUITY
BASE
Fire ProtectionProducts WIRING
DIAGRAM
TYCO FIRE PROTECTION PRODUCTS
17 MARY MULLER DRIVE
DRAWING No:
1982-71
SHEET 105of
N
P.O. BOX 19545
CHRISTCHURCH, PH: [phone]
A3 I ISS/REV
A I PART No:
NEWZEALAND. FAX:[phone]

TYCO SAFETY PRODUCTS
NEW ZEALAND.
Safety
Products
[phone]
[phone]PH:
17 MARY MULLER DRIVE
P.O. BOX 19545
FAX:
tyco
CHRISTCHURCH,
MX1
802SB / 901SB SOUNDER BASE
WIRING DIAGRAM
A3 106 N1982-71 A

+
REMOTE INDICATOR
SOUNDER/LED
OUTPUT
IN
OUT
+
+
TYCO FIRE PROTECTION PRODUCTS
NEW ZEALAND. [phone]
[phone]PH:
17 MARY MULLER DRIVE
P.O. BOX 19545
FAX:
CHRISTCHURCH,
Fire Protection Products
tyco MX1
D51MX DUCT SAMPLING UNIT
WIRING DIAGRAM
A3 168 N1982-71 A