Tynetec ZXT413 User manual

DocNo.FM0795issueBPage1
tynetec
tynetec
tynetec
169MHzTelecareDevices
FallDetector(v2)
__________________________________________________________________________________________________________


CompatiblewithReachat‐homealarms,Adventxtwardencall,
AltecResponseandAidcallTouchsafeProNursecallsystems
3impactsensitivitysettings
Vibrationalertandtri‐colourLEDindicatorlight
Auto‐canceloption
Alarmcallbutton
LonglifeLithiumbatterywithlowbatterywarning
Waterresistant:IP67
Dimensions:57mmx34mmx16mm(HxWxD)
Weight:23grams
ProductCode:ZXT413

HowdoestheFallDetectorwork?

Wornonthewrist,thefalldetectorautomaticallydetectsachangeinaccelerationthatisrelatedtotripsandstumbles,itthen
monitorsforthesubsequentimpactassociatedwithafall.

Ifafallisautomaticallydetected,theunitcanbesettovibratetoalerttheuserthatanalarmcallisabouttobetransmitted
(vibratealerton/offisanoptionalsetting).Analarmcallwillbetransmittedaftera10seconddelayunlesscancelledbytheuser.

Iftheusershakestheirwristwithin10secondsofafallbeingdetectedthealarmcallcanbecancelledautomatically(auto‐cancel
isanoptionalsetting).WhenanalarmcalliscancelledthelightwillflashGREEN.
IfnocancellationactionistakenthelightwillflashREDandanalarmcallwillbetransmitted.

ThelargeSILVERbuttoncanbepressedtoraiseanalarmcallatanytime,ifitispressedwithin10secondsofafallbeingdetected
afallalarmwillbetransmittedimmediately–thelightwillflashRED.

Duetothecomplexnatureoffallsitmaynotbepossibleforthefalldetectortoautomaticallydetectallfalls.
Usersshouldbeadvisedthatiftheyareable,topressthesilverbuttononthefalldetectoriftheyneedhelp.

WearingOptions

Thefalldetectorisnormallywornonthewristlikeawatch.Tominimise
falsealarmsitshouldbewornontheleastdominantside;i.e.aright
handedpersonshouldwearitontheirleftwristandvice‐versa.
Itcanalsobewornonthewaistbandofaskirtortrousers
byfittingthebeltclipoptionsupplied.

Fittingthebeltclipoption‐firstremovethewriststrapby
unclippingthe2blackplasticinsertsfromtheback.    

Fitthebeltclipparttothetopandblankingparttothe
bottomofthefalldetector–seealongside...

FallDetectorFeatures


  BLACKPROGRAMMODEBUTTON

  GREENAMBERREDINDICATORLIGHT

  SILVERALARMCALLBUTTON


BatteryLife

Thebatteryconditionischeckedeveryday,ifthevoltagefallsandstaysbelowapresetlevelfor7consecutivedaysalowbattery
alertisautomaticallytransmitted.Oncealowbatterycallisreceivedthefalldetectorshouldbereplacedwithin7days.
FalldetectorsmustbereturnedtoTynetec/Aidcallforbatteryreplacement.
DetailedinformationonbatterymanagementforallTynetec/Aidcallproductsisavailable–requestDocNo.FM0630.

Therangeofallradiodevicescanbeaffectedbytheworkingenvironment‐alwaystakecareduringinstallationand
performseveraltestcallsfromallextremesofthehome.




Tynetec andAidcallare businessunitsofLegrandElectricLtd
Unit10CowleyRoad,BlythRiversideBusinessPark,Blyth
Northumberland,NE245TF.Tel:01670352371Fax:01670362807
Email:[email protected]Web:www.tynetec.co.uk

PULLTHEWRIST
STRAPTOREMOVE
THE2BLACK
PLASTICINSERTS
FROMTHEFALL
DETECTORBODY.


FITTHEBELTCLIP
PARTTOTHETOP
ANDTHEBLANKING
PARTTOTHE
BOTTOMAS
SHOWNHERE.
 

DocNo.FM0795issueBPage2
tynetec
SwitchingtheFallDetectorON

Thefalldetectorisswitchedofftoconservebatterylifeintransit,toturnthefalldetectoron…


  





ProgrammingMode

Thereare4programmingoptionsavailable;

1=SensitivitySetting thissetsthelevelofimpactrequiredtoactivateafallalarm
2=VibrationAlerton/off thisprovidestheuserawarning10secondsbeforeafallalarmwillbetransmitted
3=Auto‐Cancelon/off thisdetermineswhetherafallalarmcanbecancelledbytheuser
4=TransportMode thisturnsthefalldetectorofftoconservebatterylifewhennotinuse

ToenterProgrammingMode;
PressandholdthesmallBLACKbuttonuntiltheunit((VIBRATES))thenrelease
ThelightwillflashthroughAMBERGREENREDforseveralsecondswhilea“FALL”alarmisbeingtransmitted
Whenthelightstopsflashingtheunitwill((VIBRATE))againtoindicateitisinProgrammingMode.

ToselecttheMenuOption;

PressthesmallBLACKbuttontostepthroughthe4menuoptions
ThelightwillflashREDand1to4vibrationswillbefeltaseachmenuoptionisreached
PressthelargeSILVERbuttontoselectthechosenoption,theunitwill((VIBRATE))toconfirmselection.
Note:ifnobuttonsarepressedfor10secondsthelightwillflashgreenandunitwillexitprogrammingmode.

Option1:SensitivitySetting
Whenmenuoption1isselectedthelightwillflashGREENanumberoftimestoindicatethecurrentsensitivitysetting
PressthesmallBLACKbuttontostepthroughtheSensitivitySettinglevels
TheunitwillvibrateandflashitslightRED1,2,or3timestoindicatethenewsensitivitylevel
1=High,2=Medium(default)and3=Low
OncethedesiredlevelisreachedpressthelargeSILVERbuttontoconfirm
Theunitwill((VIBRATE))thenflashGREENAMBERREDtoconfirmitssettings(seepage3)beforeexitingprogrammingmode.

Option2:VibrationAlertOn/Off
PlacetheunitintoProgrammingModeandselectmenuoption2
Whenoption2isselectedthelightwillflashAMBERanumberoftimestoindicatethecurrentvibrationalertsetting
PressthesmallBLACKbuttontotoggleVibrationAlertON/OFF
1vibration&1REDflash=VibrationAlertON
2vibrations&2REDflashes=VibrationAlertOFF(default)
OncethedesiredsettingismadepressthelargeSILVERbuttontoconfirm
Theunitwill((VIBRATE))thenflashGREENAMBERREDtoconfirmitssettings(seepage3)beforeexitingprogrammingmode.

Option3:Auto‐CancelOn/Off
Placetheunitintoprogrammingmodeandselectmenuoption3
Whenoption3isselectedthelightwillflashREDanumberoftimestoindicatethecurrentauto‐cancelsetting
PressthesmallBLACKbuttontotoggleAuto‐CancelON/OFF
1vibration&1REDflash=Auto‐CancelOFFi.e.analarmcannotbecancelledregardlessofactionbytheuser(default)
2vibrations&2REDflashes=Auto‐CancelON;analarmcallcanbecancelledbymovement(i.e.shakingthewrist)beforeand
afterthe5secondvibrationperiod
OncethedesiredsettingisselectedpressthelargeSILVERbuttontoconfirm
Theunitwill((VIBRATE))thenflashGREENAMBERREDtoconfirmitssettings(seepage3)beforeexitingprogrammingmode.

Option4:SwitchingtheFallDetectorOFF(TransportMode)

Placetheunitintoprogrammingmodeandselectmenuoption4
Whenoption4isselectedthelightwillflashREDtwicetoindicateTransportMode
PressthelargeSILVERbuttontoconfirmandthelightwillflashREDthreetimes
Theunitwill((VIBRATE))thenflashGREENAMBERREDtoconfirmitssettings(seepage3)beforeswitchingoff.







PressandholdthelargeSILVERbuttonfor3secondsthenrelease,thelight
willflashREDforseveralsecondstoindicatetheunitisswitchedon.

DocNo.FM0795issueBPage3
tynetec tynetec tynetec
tynetec
ConfirmationofSettings

WhenevertheunitexitsprogrammingorregistrationmodeitwillvibrateandflashitslightGREENAMBERREDanumberoftimes
toindicateitsSensitivitySetting,ifVibrationAlertisonoroffandifAuto‐Cancelisonoroff.AftertheREDflashsequencethefall
detectorwillreturntonormaloperatingmode.




      











RegisteringaFallDetectorontoaReachat‐homealarmunit

1.PuttheReachunitintoradiodevicelearnmode…










2.Activatethefalldetector…









3.Exitradiodevicelearnmode…










4.CheckwiththeControlCentrethatitisconvenienttoperformatestcall,activatethefalldetectorbothwaysandconfirmthey
receivebothpendantandfallalarmcalls.

DeletingaFallDetectorfromaReachat‐homealarmunit

Enter1670usingthekeypadontherearoftheReachunit–thefrontlightwillFLASHFASTGREENandtheunitwillannounce
“ProgramMode‐Ready”.
Enter#041andtheReachwillannounce“DeleteRadioDevice”followedbya“Beep”.
Enterthe8digitfalldetectorID(22xxxxxx)tobedeletedandtheunitwill“Beep”.
Enterthe8digitpendantID(20xxxxxx)tobedeleted,afterthe“Beep”press#toexit.
PressthekeytoexitProgramMode;theunitwillsounda“Double‐Beep”andthefrontlightwillreturntoSTEADYGREEN.



TheseinstructionsapplytothestandardReach,ReachPlus,ReachPlusGSMandReachUltramodels.
Refertotheinstructionbookletsprovidedwiththeseproductsformoreinformation.


followedby…
GREENFLASHESindicatethe
Sensitivitysetting;
1=High(mostsensitive)
2=Medium(default)
3=Low(leastsensitive)
followedby…
AMBERFLASHESindicatethe
VibrationAlertsetting;
1=VibrationAlertON
2=VibrationAlertOFF(default)
   
PressandHOLDtheGREENbuttonontheReachunit.

WhenthefrontlightFLASHESFASTGREENreleasethe
buttonandtheReachwillannounce“TriggerRadioDevice”.

Younowhave1minutetoactivatethefalldetector.

PresstheGREENbuttonontheReachunit.

ThefrontlightwillreturntoSTEADYGREENandtheReach
unitisnowbackinnormaloperatingmode.

“Trigger
Radio
Device”

REDFLASHESindicatethe
Auto‐Cancelsetting;
1=Auto‐CancelOFF(default)
2=Auto‐CancelON
PressandHOLDthelargeSILVERbuttonfor3secondsthenrelease,thelightwill
flashREDforseveralsecondsandtheReachunitwillannounce“Pendant”.

After5seconds,thelightwillstartflashingREDagainandtheReachunitwill
announce“Fall”.

DocNo.FM0795issueBPage4
tynetec
tynetec
tynetec
RegisteringaFallDetectorontoanAdventxtwardencallsystem

1.PuttheAdventxtsystemintoradiodevicelearnmode…














2.FirstactivateaPENDANTalarmonthefalldetector…

 






3.ThenactivateaFALLalarmonthefalldetector…


 





4.Exittheregistrationmode…


   











5.Activatethefalldetectorandcheckbothpendantandfallalarmcallsarereportedonthewardencallsystem.

DeletingaFallDetectorfromanAdventxtwardencallsystem

PresstheLINEkeyandwaitforthe“Ready”prompt,enter5001followedbythekey.
Waitforthe“RadioDeviceDisable–EnterFlat”prompt.
Entertheflatnumberthefalldetectorisbeingdeletedfromfollowedbythekey.
Usingthefalldetectortobedeleted,pressthelargeSILVERbuttononthefalldetectortobedeleted.
Waitforthe“PendantRadioDeviceDisabled–EnterFlat”prompt.
Enterthesameflatnumberthefalldetectorisbeingdeletedfromagainfollowedbythekey.
ThistimepressandholdthesmallBLACKbuttonuntiltheunitvibratesthenrelease.
Waitforthe“FallRadioDeviceDisabled–EnterFlat”prompt.
Pressthe#keyandwaitforthe“Ready”prompt,thenpresstheLINEkeytocleartheconnection.




RefertotheAdventxtoperatorsmanual(DocNo.FM0420)providedwiththewardencallsystemformore
informationonprogrammingandtestingradiodevices.



UsingtheManager’sDECTphone;

PresstheLINEkeyandwaitforthe“Ready”prompt.

Enter5000followedbythekey.

Entertheflatnumberthefalldetectorisbeinginstalledinfollowedbythekey.

Waitforthe“Flat“x”–EnableRadioDevice”prompt

Younowhave1minutetoactivatethefalldetector.

“Ready”
“Ready”
PressandholdthesmallBLACKbuttonforabout3secondsuntilthefalldetector
vibratesthenrelease;thelightwillflashAMBERGREENREDforseveralseconds.

Waitforthe“FallRadioDevice–EnterLocationCode”promptthenpress0(no
location)followedbythekey.

Waitforthe“LocationCode0–RadioDeviceEnabled–EnterFlat”prompt.
PresstheSILVERbuttononce,thelightwillflashREDforseveralseconds.

Waitforthe“PendantRadioDevice–EnterLocationCode”promptthenpress0
(nolocation)followedbythekey.

Waitforthe“LocationCode0–RadioDeviceEnabled–EnterFlat”prompt.

Enterthesameflatnumberagainfollowedbythekey.


PresstheSILVERbuttontoexitthefall
detectorregistrationmode,orafter
about10secondsitwillexititself.
Onexititwillvibrateandflashasequence
ofcolourstoconfirmitssettings(seepage3).

UsingtheManager’sDECTphonepressthe#key
andwaitforthe“Ready”prompt.

PresstheLINEkeytocleartheconnectionand
thewardencallsystemisnowbackinnormal
operatingmode.


DocNo.FM0795issueBPage5
tynetec
tynetec
tynetec
RegisteringaFallDetectorontoanAltecResponselocalcareralarmunit

1.PuttheAltecResponseunitintoradiodevicelearnmode…















2.ActivateaPENDANTalarmonthefalldetector…

 










3.ActivateaFALLalarmonthefalldetector…


 





4.Exitthefalldetectorregistrationmode…


   






5.ExittheAltecResponseradiodevicelearnmode…
 
     
 




 







6.ActivatethefalldetectorandcheckbothpendantandfallalarmcallsaredisplayedontheAltecResponseunit.


PressandholdthesmallBLACKbuttonforabout3secondsuntilthefalldetector
vibratesthenrelease;thelightwillflashAMBERGREENREDforseveralseconds.
Whenthetransmissioniscompletethefalldetectorwillvibrateagain.

ThedisplaywillshowFallDetectorandthefalldetector8digitIDnumber.
IftheIDiscorrectpressthekeytoselectAcceptthenpressENTER.
Re‐enterthesamedetailsasaboveforthefalldetector.
PressthelargeSILVERbuttononce,thelightwillflashREDforseveralseconds.

ThedisplaywillshowPersonalPendantandthefalldetector8digitIDnumber.
ChecktheIDiscorrect,pressthekeytoselectAcceptthenpressENTER.
Note:ifanotherdevicehasbeenpicked‐uppressENTERtoRejectandtryagain.
ThedisplaywillshowFlat,usethe&keystochoosethedwellingtype.
PressthekeytoselectNo:000000thenpresstheENTERkey.
Usethe&keystoselecteachdigitoftheflatnumberandthe&keysto
movebetweendigitsthenpresstheENTERkey.
PresskeyseveraltimestoselectExitthenpresstheENTERkey.
Thedisplaywillpromptyouto“TriggertheSensor”again.
PressthelargeSILVERbuttononce,thefalldetectorwillvibrateandthelight
willflashasequenceofcolourstoconfirmitssettings(seepage3).

or…afterabout10secondsthefalldetectorwillexitregistrationmode
automaticallyandconfirmitssettings.
PressENTERtoactivatethewake‐updisplaythenENTERagaintodisplay
themainmenu.

PressENTERtoselectRadioDevices

PressENTERtoselectLearnDevice

Thedisplaywillpromptyouto“TriggertheSensor”.

Younowhave20secondstoactivatethefalldetector.



FromtheLearnDevicemenuselectExitthenpressENTER.

FromtheRadioDevicesmenuselectExitthenpressENTER.

Thedisplaywillreturntothewake‐upscreenandgoblankafter10seconds.

TheAltecResponseisnowinnormaloperatingmode.

tynetec
tynetec

DocNo.FM0795issueBPage6
DeletingaFallDetectorfromanAltecResponselocalcareralarmunit

PressENTERtoactivatethewake‐updisplaythenENTERagaintodisplaythemainmenu
PressENTERtoselectRadioDevices
PressthekeytoselectDeleteDevicethenpressENTER
Thedisplaywillpromptyouto“TriggertheSensor”
Usingthefalldetectortobedeleted,pressandholdthesmallBLACKbuttonuntiltheunitvibratesthenrelease‐thedisplaywill
showthedevicetypeandits8digitIDnumber
IfthisisthedeviceyouactivatedpressthekeytoselectDeletethenpressENTER
Ifit’sNOTthedeviceyouactivatedpresstheENTERkeytoselectRejectthentryagain
PressthelargeSILVERbuttononthefalldetectortobedeleted‐thedisplaywillshowthedevicetypeandits8digitIDnumber
IfthisisthedeviceyouactivatedpressthekeytoselectDeletethenpressENTER
Ifit’sNOTthedeviceyouactivatedpresstheENTERkeytoselectRejectthentryagain
ToexitthemodeselectExitthenpresstheENTERkey.





RefertotheAltecResponseinstallationguide(DocNo.FM0548)providedwiththeportablealarmunitfor
moreinformationonprogrammingandtestingradiodevices.




RegisteringaFallDetectorontoaTouchsafeProNursecallsystem

1.PuttheTouchsafeProMasterPanelintoTelecareregistrationmode;touchthescreenandLogonasanEngineeroraManager
(passwordrequired),thenfromthemainmenupagetouchtheTelecarebuttontoopenthescreenshownbelow…























2.EnterthefalldetectorID…
 
















3.PresstheClosebuttontoexitTelecaremodeandtheNursecallpanelisnowinnormaloperatingmode.

The8digitIDisprintedonthesilverlabelontherearofthefalldetector.
Note:thisIDwillalwaysstartwith22xxxxxx(22prefix=fall).

TouchtheAddTelecareDeviceboxthenusetheon‐screenkeypadtoentertheID.

Hint:enterazoneintheFilterboxtonarrowthesearchfortheroom.

SelecttheusersCallPointIDfromtheRoompull‐downboxthenpressSave.
Note:thisistheroomunitthatwillbewillbeusedtocancelthecall.

Usetheon‐screenkeypadtoenterthesame8digitIDagainbutthistimechange
thefirst2digitsfrom“22”to“20”(20prefix=pendantcall).

SelectthesameZoneandCallPointIDasabovethenpressSave.
ID:22408597
Ser:251718194
ZXT413
Iss:1
Freq169MHz
EnvGroupII
*Note:falldetectorID
mustbeenteredtwice;
Prefix22=falland
Prefix20=pendant
Usekeypadtoenter
8digitID*here
Selecttherelevant
CallPointIDhere
Savewhendone
Closetoexitmode
On‐screenkeypad

DocNo.FM0795issueBPage7
4.PresstheSILVERbuttononthefalldetectorandcheckthecallisdisplayedontheNursecallpanellikethis…






Thescreenbannerisorangeforapendantcall(Touchthebannertodisplaynotes).
PresstheAcceptbuttononthebannertosilencethealarm‐thiswillalso
notifyallotherpanelsthecallisbeingdealtwith.
Thescreenbannerchangestopurplewhenacallisaccepted.
YoumustvisittheappropriateNursecallCallPointtocancelthecall.

5.PressandholdthesmallBLACKbuttonforabout3secondsuntilthefalldetector
vibratesthenrelease,checkthealarmisdisplayedontheNursecallpanellikethis…






Thescreenbannerisredforafallalarm(Touchthebannertodisplaynotes).
Afallalarmcannotbeacceptedorsilencedfromthescreen.
YoumustvisittheappropriateNursecallCallPointtocancelthecall.


DeletingaFallDetectorfromaTouchsafeProNursecallsystem

SelectthefallDetectorIDtobedeletedfromtheDeleteTelecareDevicepull‐downlistbox(prefixedwitha“T22”).
DetailsofthefalldetectorselectedwillbedisplayedintheRoom,HouseCodeandIDboxesbelow.
IfthedetailsshownarecorrectpresstheDeletebutton.
SelectthependantIDtobedeletedfromtheDeleteTelecareDevicepull‐downlistbox(prefixedwitha“T20”).
DetailsofthependantselectedwillbedisplayedintheRoom,HouseCodeandIDboxesbelow.
IfthedetailsshownarecorrectpresstheDeletebutton.
PresstheClosebuttontoexit.





RefertotheTouchsafeProDisplayPaneluserguide(DocNo.FM5505)providedwiththeNursecallsystemfor
moreinformation.




























TynetecandAidcalloperateapolicyofcontinuousimprovementandreservetherighttochangeproductspecificationswithoutnotice.
Ifanyvariationtothedetailscontainedinthisdocumentaresuspectedpleasecontactourcustomersupportdepartmenton01670352371.
CALLING
CANCEL
HC345ID001
PresstheLIGHTGREY
buttontocancelthecall