Tzora APT-5 User manual

APT-5 - User’s Manual (EU) Rev. 2020-01 en 2
SECTION A – PRE-SALES INFORMATION
01 INTRODUCTION
The APT-5 is an electric exercise machine used for the improvement of physical abilities.
The APT-5 provides the user with a variety of exercise options and modes of operation
that meet a broad range of physical needs.
A wide range of accessories are available that offer many exercise options and make the
APT-5 suitable for the maintenance of fitness and physical well being.
The APT-5 can be operated in either the ACTIVE mode at varying degreesof resistance or
in the PASSIVE mode at adjustable speed and torque levels. In the PASSIVE mode it is also
possible to combine PASSIVE with ACTIVE training by using physical effort in conjunction
with the electrical operation of the motor. The APT-5 functions forwards or backwards
and is suitable for arm or leg exercises (upper or lower limbs). In case the user has limited
strength in the arm, it is recommended to have an attendant present during exercise.
The APT-5’s light weight makes it portable, easy to store and convenient to use.
Use of the APT-5 is recommended for the maintenance of muscle strength, flexibility,
muscle tone, endurance and general fitness for users of all ages.

APT-5 - User’s Manual (EU) Rev. 2020-01 en 3
SECTION A – PRE-SALES INFORMATION
02 TECHNICAL DATA
APT-5
Weight..............................................................................................10 kg. (22 lbs.)
Length ..............................................................................................72 cm. (28 in.) overall
Width................................................................................................46 cm. (18 in.)
Height ..............................................................................................16 cm. (6½ in.) folded
Working voltage ..............................................................................24 VDC
Revolutions per minute ..................................................................20-60 RPM
Current Rating .................................................................................4.16 A Max.
Accuracy of measurement display.................................................±10%
Liquid ingress protection level.......................................................IPX1
Continuous operation
Equipment not suitable for use in the presence of flammable anaesthetic mixture with air
or with oxygen or nitrous oxide.
WARNING: To avoid the risk of electric shock, this equipment must only be connected to a
supply mains with protective earth.
The APT-5 and its accessories have been designed and manufactured in accordance with
the specification of the following:
DIRECTIVE: Medical devices 93/42 EEC (Annex V)
External Power Supply
Weight..............................................................................................800 g. (1.8 lbs.)
Length ..............................................................................................19 cm. (7½ in.)
Width................................................................................................9 cm. (3½ in.)
Height ..............................................................................................4.6 cm. (1¾ in.)
Input:................................................................................................100-240 V 47-63 Hz 1/25 A
Output:.............................................................................................24 VDC 100 W Max. 4.16 A
Type B equipment
Class I equipment

APT-5 - User’s Manual (EU) Rev. 2020-01 en 4
SECTION A – PRE-SALES INFORMATION
03 USER INFORMATION
3.1 Intended Use
The Active Passive Trainers are electric exercise machines used for the improvement of
physical abilities. The trainers provide the user with a variety of exercise options and
modes of operation that meet a broad range of physical needs:
• Fitness: the maintenance of muscle strength, flexibility, muscle tone, endurance and
general fitness for users of all ages;
• Rehabilitation: spinal cord injury, geriatrics, CVA, cardiac and pulmonary, paediatric,
haemodialysis (training during treatment), general.
3.2 Indications
The Active Passive Trainers are intended to be operated by persons of most physiques
and ages. In case the user has limited strength in the arm or cognitive impairment, it is
required to have an attendant present during exercise.
The Active Passive Trainers provide the user with a variety of exercise options and modes
of operation that meet a broad range of phys ical needs. Use of the Active Passive Trainer is
recommended for the maintenance of muscle strength, flexibility, muscle tone, endurance
and general fitness for users of all ages.
3.3 Contraindications
People with limited cognitive abilities and children should not use the Active Passive Trainer
unsupervised.
In case of any disease or physical complaints, a healthcare provider should be consulted
before participating in any exercise program.
Immediately stop exercising when feeling dizzy, pains, nauseous or any other physical
discomfort. In case of recurring discomforts, con sult with a health care provider.
>>

APT-5 - User’s Manual (EU) Rev. 2020-01 en 5
>>
Risk analysis and long term experience in the field of movement ther apy show that patients
with the following indications are required to consult their doctor and therapist before starting
the training:
• Fresh joint injuries
• joint replacements/prosthetics
• fresh ligament reconstruction
• fresh knee- and hip prosthetics
• knee and joint arthritis
• joint stiffness
• extreme muscle shortening
• extreme limb deformation
• increased danger of hip and shoulder luxation (e.g. sub luxation in shoulder)
• acute thrombosis
• decubitus
• very strong osteoporosis
3.4 Safety
These safety considerations and tips will help you to operate the APT-5 safely and prevent
personal injury and damage to your wheelchair.
1. Read this manual and all labels before operating. If you do not ful ly understand any part of
this manual, please contact your author ized dealer or service agent.
2. The APT-5 should not be used in the vicinity of sensitive medical equipment.
3. Electromagnetic interference (“EMI”) can cause APT-5 to behave erratically, which could be
dangerous to the user. For your safety and protection, it is imperative that you read the
information on EMI before operating the APT-5 , see chapter 11.
4. EMC Warning: Radio wave sources such as radio and T.V. sta tions, transmitters and cellular
telephones can affect the performance of powered wheelchairs and mobility devices.
5. Do not operate the APT-5 when under the influence of alcohol, medications or drugs that
may impair your safety.
>>

APT-5 - User’s Manual (EU) Rev. 2020-01 en 6
>>
6. Only the authorized dealer or service agent may perform specified set-up procedures
and controller settings; programming of the set tings outside the limits as specified by the
manufacturer may have adverse effects on the performance.
7. Do not use the APT-5 if it behaves abnormally or erratically, con trary to the usual performance
as described in this user manual.
8. CAUTION: Surface temperatures can increase when exposed to external sources of heat
(e.g. sunlight).

APT-5 - User’s Manual (EU) Rev. 2020-01 en 7
SECTION A – PRE-SALES INFORMATION
04 SYSTEM COMPONENTS AND DETAILS
4.1. APT-5 unit (Figure 1)
4.2. Primary components (Figure 2):
>>
1. Operator panel
2. Angle release knob
3. Angle securing knob
4. Crank-arm
5. Power input socket
6. Socket (not in use)
7. Height release knob (Hi-Lo only)
8. Height securing knob (Hi-Lo only)
1. Power supply unit
2. Straight hand-grips
3. Footrests
4. Finger protection disks
5. Securing straps

APT-5 - User’s Manual (EU) Rev. 2020-01 en 8
4.3. The Type Plate
The Type Plate can be found on the underside of the APT-5 body next to the power input socket.
This label contains the serial number of the APT-5 The serial number consists of 11 digits and
one letter:
Example: Serial no. 32001103001X
3200 11 03 001 X
12345
1. Model: APT-5
2. Year of manufacturing (last two digits of the year)
3. Month of manufacturing
4. Sequential number of batch
5. Letter identifying the manufacturing location
Liquid ingress protection level
Read this user manual and all labels before operating.
When this equipment is no longer operational it must be sent to a separate collection
facility for recovery and recycling.
CE approved Notified Body No. 0123.
Type B equipment.
Read the warnings in this manual before operating.
IPX1
Figure 2A
>>

APT-5 - User’s Manual (EU) Rev. 2020-01 en 9
4.4 The APT-5 - Operator Panel
1On/Off button: green indicator is lit when the APT-5
is switched on.
2Mode button: for selecting active or passive mode
of operation.
3Green indicator is lit when ACTIVE mode is selected
by mode button.
4Green indicator is lit when PASSIVE mode is selected
by mode button.
5Indicates actual load level as percentage of chosen
load level (see 16).
>>

APT-5 - User’s Manual (EU) Rev. 2020-01 en 10
6
Button for forward operation in the PASSIVE
mode. The green indicator is lit to indicate forward
operation.
7
Button for backward operation in the PAS SIVE
mode. The green indicator is lit to indi cate backward
operation.
8
Button activating Auto-Reverse function in the
PASSIVE mode. In the ACTIVE mode this button
activates the constant force func tion. The green
indicator is lit when activated.
9Button for selecting display of data, (see 10-13):
10
Green indicator is lit when Timer display is selected.
The display will show the time the APT-5 has been
used in the current exercise period.
11
Green indicator is lit when Counter display is
selected. The display will show the total amount of
revolutions of the crank arm in the current exercise
period.
12
Green indicator is lit when Power display is selected.
The display will show the power during exercise in
Watts – only in Active mode.
13 Not in use
14 Display for Timer, Counter and Energy.
15
Exercise speed level selection push buttons
15a – Increases speed level (up to 10)
15b – Decreases speed level (down to 1)
16
Exercise load level selection push buttons
16a – Increases load level (up to 10)
16b – Decreases load level (down to 1)
>>

APT-5 - User’s Manual (EU) Rev. 2020-01 en 11
SECTION A – PRE-SALES INFORMATION
05 ACCESSORIES
The following items are designed for use in combination with the APT-5.
CAUTION: The use of accessories other than these can be unsafe.
5.1 Hand grips and Footrests
#ACCESSORY USAGE DESCRIPTION FIGURE
aStraight
Handgrips
Used for most of the upper limb exercis ing.
bAngled
Handgrips
Ergonomically designed, mainly for strength
exercising in the Active mode.
cHemi-glove Used for securely supporting the wrist and hand on
the handgrips for users who have little or no muscle
strength.
dPediatric
Hemi-glove
Hemi-glove specially designed to be used by children.
eStandard
Footrests
Used for most of the lower limb exercising.
fPediatric
Footrest
Footrest specially designed to be used by children.
gHigh support
for footrests
May be attached to footrests for support ing the
lower limbs of users that have little or no muscle
strength.
hHandle Bar Used to improve hold on APT-1 during leg exercise.
5.2 Optional added functions
#ACCESSORY USAGE DESCRIPTION FIGURE
aRemote
Control
Used mainly for lower limb ex ercising by users who
have dif ficulty in reaching the operating panel.

APT-5 - User’s Manual (EU) Rev. 2020-01 en 12
SECTION B – USER INFORMATION
06 PREPARING THE APT-5 HI-LO
6.1 Moving your APT-5 Hi-Lo
The APT-5 Hi-Lo can easily be moved by lifting the end of the frame and pushing the unit
using its wheels, see Figure 4.
6.2 Positioning the APT-5 Hi-Lo
Position the APT-5 Hi-Lo close to an electrical socket outlet. The ad justable feet on the
underside keep the APT-5 Hi-Lo level and pre vent it from sliding.
NOTE: Ensure that the APT-5 Hi-Lo is level in order to prevent dam age to the trainer or its
components.
If readjustment of one of the feet is needed, open the contra nut (4A/1), turn the foot
(4A/2) to the desired height and secure the foot with the contra nut (4A/1).

APT-5 - User’s Manual (EU) Rev. 2020-01 en 13
SECTION B – USER INFORMATION
07 INSTALLATION FOR USE – ARMS EXERCISE
Position the APT-5 on a level table top close to an electrical socket outlet (Figure
5). For the APT-5 Hi-Lo: loosen the height securing knob (Figure 1A-8), pull the grey
ring of the height release knob (Figure 1A-7) and adjust the unit to the required
height. Release the grey ring and tighten the height securing knob (Figure 1A-7).
Loosen the angle-securing knob (Figure 5-1) and adjust the APT-5 to the required
angle. To increase the angle, lift the body of the APT-5, allow it to “click” into
one of the operating positions and retighten the securing knob. To decrease the
angle, pull the an gle release knob (Figure 6), lower the body of the APT-5, allow it
to “click” into another operating position and tighten the securing knob.
CAUTION: Make sure that the minimum distance between crank arm and the
table surface is approximately 5 cm. / 2” (Figure 5-2).
Connect the output connector (Figure 7-1) of the power supply (Figure 7-4) to
the APT-5 power input socket (Figure 7-2a) while ensuring correct position of
connector groove opposite the guide key of socket (Figure 7-2b).
NOTE: The APT-5 must be used only with an original APT-5 Power Supply unit.
Step 1:
Step 2:
Step 3:

APT-5 - User’s Manual (EU) Rev. 2020-01 en 14
>>
Install the finger protection discs (Fig. 8-1) by sliding them into the grooves on the
outside edges of the crank arms (Figure 8-2) in the direction shown.
NOTE: The finger protection discs are important for safe opera tion of the unit
during hands exercise.
Insert handgrip (Figure 9-1) in one of the four mounting holes (Figure 9-2) in each
of the APT-5 crank arms. Installation or re moval requires only a straight push or
pull while simultaneously pressing on the release pin (Figure 9-3) at the end of
the handle.
NOTE: The choice of mounting hole provides variable resistance levels and ranges
of motion. See operation instructions.
Plug the power supply mains power plug into the electrical socket outlet (Figure
5-3). To start operating, press the button.
The APT-5 will enter the stand-by position. Then press the button. The
green ACTIVE mode indicator will light up. You may start exercising in the ACTIVE
mode. For operation instructions, see 5.1 & 5.2.
NOTE: If the APT-5 moves across the table during arm exercis es, anti-slip pads
(Figure 8-3) may require cleaning.
Step 4:
Step 5:
Step 6:

APT-5 - User’s Manual (EU) Rev. 2020-01 en 15
SECTION B – USER INFORMATION
08 INSTALLATION FOR USE – LEG EXERCISE
Position the APT-5 on the floor close to an electrical socket outlet (Figure 10).
Loosen the angle-securing knob (Figure 10-1) and adjust the APT-5 to the required
angle. To increase the angle, lift the body of the APT-5, allow it to “click” into
one of the operating positions and retighten the securing knob. To decrease the
angle, pull the angle release knob (Figure 11), lower the body of the APT-5 , al low
it to “click” into another operating position and tighten the se curing knob.
CAUTION: Make sure that the minimum distance between crank arm and the
floor surface is approximately 5 cm. / 2” (Figure 10-2)
Place a chair at the desired distance from the APT-5. If necessary, attach the
Securing straps (Figure 10-6) between the APT-5 base rings (Figure 10-5) and the
chair legs to prevent any change in distance between the APT-5 and the chair
during leg exercises.
Step 1:
Step 2:
Step 3:

APT-5 - User’s Manual (EU) Rev. 2020-01 en 16
>>
Connect the power output connector (Figure 12-1) of the power supply (Figure 12-
4) to the APT-5 power input socket (Figure 12-2a) while ensuring correct position
of connector groove opposite the guide key of socket (Figure 12-2b).
NOTE: The APT-5 must be used only with an original APT-5 Power Supply unit.
Insert Footrest (Figure 13-1) in one of the four mounting holes (Figure 13-2) in
each of the APT-5 crank arms. Installation or removal requires only a straight
push or pull while simultaneously pressing on the release pin (Figure 13-3) as
shown. Secure feet in place with straps fastened diagonally as shown in Figure 10.
NOTE: The choice of mounting hole provides variable resistance levels and ranges
of motion. See operation instructions.
Plug the power supply mains power plug into the electrical socket outlet (Figure
10-3). The APT-5 will enter a stand-by position.
To start operating, press the button. The APT-5 will enter the stand-by
position. Then press the button. The green ACTIVE mode indicator will light
up. You may start exercising in the ACTIVE mode. For operation instructions, see
5.1 & 5.2.
NOTE: If the APT-5 moves across the floor during leg exercises, anti-slip pads
(Figure 8-3) may require cleaning. If possible – use the APT-5 on a carpet or rubber
mat.
Step 4:
Step 5:
Step 6:

APT-5 - User’s Manual (EU) Rev. 2020-01 en 17
SECTION B – USER INFORMATION
09 Tele APT
SENSOR User Guide
LED Status
Specifications
Connected
(Green blinking)
Wireless connection to tablets and smartphones.
12 hours of continuous use without recharging.
LED & audio indicators
Sensors: 3-axis accelerometer
Operating temp: -5oc to 45oc (23of to 113of)
Battery Type: Rechargeable 100 mAh lithium polymer
Battery Life: 12 hours of continuous use
Communication module: Bluetooth low energy (BLE)
Low battery
(Red blinking)
1
2
3
4
Charging completed
(Orange blinking)
Charging
(Blue blinking)
Download A.P.T app
http://bobo-balance.com/index-apt
Powered by bobo
Contact: [email protected]
Pairing is automatic!
Just open the app and power on the sensor
Make sure the bluetooth is enabled
on your device!
Chose your session -
Training / Games / Presets.
Chose A.P.T mode - Passive / Active / Soft.
Attach sensor to A.P.T disc.
BO&BO Ltd. O.C ID: 515218261 / [email protected] [phone] / 11Ha’avoda St, Rosh-Ha’ain, Israel
E.A.R. - Obelis S.A. Boulevard Général_Wahis 53, B-1030 Brussels, BELGIUM
.

APT-5 - User’s Manual (EU) Rev. 2020-01 en 18
SECTION B – USER INFORMATION
10 OPERATION INSTRUCTIONS
NOTE: Install APT-5 for arms or legs exercise as described in the previous chapters.
10.1 Active mode - ISOKINETIC operation
10.2 Active mode - CONSTANT FORCE Operation
Insert the handgrips or footrests in one of the four mounting holes according to
the radius and range of motion required.
NOTE: As the effective crank arm length is reduced in the ACTIVE mode, the
amount of effort required increases while the range of motion decreases, and
vice versa.
To activate the active mode from the stand-by position (after the electrical power
is supplied to the APT-5 and the button is pressed): press the button.
The green ACTIVE mode indicator will light up.
Set the desired load level by pressing one of the selection push buttons,
to increase the level or to decrease the level.
Rotate the APT-5 handgrips or footrests forward or backward. Actual exercising
force is displayed as a percentage (%) on the Bar Indicator.
NOTE: In this mode, an increase in the rotation speed (RPM) will lead to an
increase in the exercising force.
Press the button to activate the CONSTANT FORCE FUNCTION in the ACTIVE
mode. The green indicator will light up.
Set the desired load level by pressing one of the selection push buttons,
to increase the level or to decrease the level.
Rotate the APT-5 handgrips or footrests forward or backwards. The exercising
force as displayed on the Bar Indicator will now remain constant at 50% for the
selected load level, irrespective of the crank arm rotation speed.
Step 1:
Step 2:
Step 3:
Step 4:
Step 1:
Step 2:
Step 3:

APT-5 - User’s Manual (EU) Rev. 2020-01 en 19
>>
10.3 PASSIVE mode
Insert the handgrips or footrests in one of the four mounting holes according to
the radius and range of motion required.
NOTE: As the effective crank arm length is reduced in the PASSIVE mode, the
range of movement is reduced and the degree of resistance that the motor can
overcome is increased.
To activate the passive mode from the stand-by position (after the electrical
power is supplied to the APT-5 and the button is pressed): press the
button two times, until the green PASSIVE mode indicator will light up. From the
ACTIVE mode – press once only.
Set the desired rotation speed by pressing one of the speed level push buttons
and the desired force by pressing one of the force load push buttons: and
to increase level, and to decrease level.
Hold onto the handgrips (for arm exercise) or secure both feet to the footrests
(for legs exercise). Make sure that APT-5 is placed at a comfortable distance for
exercise by turning the crank arms one complete revolution.
Press the button for forward rotation.
Press the button for backward rotation.
NOTE: There will be a short delay before the APT-5 begins to turn in the chosen
direction.
The operation force of the crank arms should rotate the arms or legs of with no
effort on the part of the user. This rotation force varies according to exercise level
and crank arm mounting hole location selected.
To stop the rotation of the crank-arms and exit the PASSIVE mode, press the
button. The indicators will turn off and the APT-5 will return to the stand-
by position.
Step 1:
Step 2:
Step 3:
Step 4:
Step 5:
Step 6:

APT-5 - User’s Manual (EU) Rev. 2020-01 en 20
>>
10.4 COMBINED active/passive mode
10.5 Passive mode – AUTO-REVERSE function
Operate the APT-5 in the passive mode and work against the force of the motor
by applying resistance to the rotation of the crank arms.
The resistance force to the rotation is displayed on the on the Bar Indicator as a
percentage (%) at each level.
If the resistance force stops the crank arm rotation completely, the Bar Indicator
reaches 100% and the red indicator will light up. After holding this position for
approximately 2 seconds, the crank arm rotation will stop automatically.
NOTE: To restart, Press the button for forward rotation, or the button
for backward rotation.
Push the button to activate the AUTO-REVERSE function in the PASSIVE
mode. The green indicator will light up.
Operate the APT-5 as in usual passive or combined active/passive mode.
When the resistance force stops the crank arm rotation completely, the Bar
Indicator reaches 100% and the red indicator will light up. After holding this position
for approximately 2 seconds, the crank arm rotation will stop automatically. After
a short delay the DIRECTION OF ROTATION WILL BE RE-VERSED. This feature
also serves as an ANTI-SPASM function, stopping the motor in case of muscle
spasm and reversing the direction of rotation after a short delay.
As long as the button indicator is lit, this function will continue to operate
in the PASSIVE mode.
Step 1:
Step 2:
Step 3:
Step 1:
Step 2:
Step 3:
Step 4: