U-Line H-4618 User manual

PAGE 1 OF 2 0214 IH-4618
πH-4618, H-4619
5 cHannel caBle
PROTecTOR
1-800-295-5510
uline.com
COMPONENTS
ASSEMBLY
Interlock with dog-bone connectors to extend protection
length. (See Figure 1)
•Inspect areas for safety hazards.
•Assemble sections by aligning female connectors
over male connectors and press with foot to secure.
•Using through-holes, fasten protector to ground
(optional - see Mounting Instructions).
•Close cover flush with base.
•Test installation for intended use.
•Periodically inspect installation.
CHANNEL CAPACITY
CHANNEL CAPACITY - MAX. DIAMETER INCHES
4 Outer Channels 1.339" width x 1.325" height
Center Channel 1.704" width x 1.325" height
LOAD CAPACITY
The 5 Channel Cable Protector has different load
supporting capabilities depending on type of vehicle
and temperature. Suitability must be verified by testing
under actual conditions.
Load-supporting capacity varies by type of loading
conditions and environmental conditions. The load
capacity decreases in warm environments. Test before
use and inspect periodically.
MODEL
NO.
LOAD CAPACITY PER TIRE
MAX LOAD 70°F (21°C)
LOAD CAPACITY PER AXLE
MAX LOAD 70°F (21°C)
H-4618 10,500 lbs. 21,000 lbs.
OPERATING TEMPERATURE
-40° to 120°F (-40° to 48°C)
CHEMICAL RESISTANCE
Tested for compatibility with common motor oils, gasoline
and diesel fuel. Limited resistance to brake fluids and
other chemicals.
MATERIAL
UV-stabilized polyurethane elastomer.
INSTRUCTIONS
Figure 1
36" Lineal Protector End CapEnd Cap

PAGE 2 OF 2 0214 IH-4618
CAUTION: Misuse can cause electrical shock
and injury.
•DO NOT use as work surface. NO CUTTING, NO
DRILLING, NO HAMMERING.
•Use with momentary loads only. DO NOT place
ladders, scaffolds or any type of structure on the
protector.
•Avoid concentrated loads.
•Use only on a stable surface. Inclined surfaces,
slippery surfaces and broken ground can cause
injury.
•This protector can be a trip hazard to pedestrian
traffic if they are unaware of its presence.
•Keep the 5 Channel Cable Protector clean and
bright.
•Keep various services, communications, fluids and
power separated. Limit a channel to one service type.
•Polyurethane is attacked by some chemicals. Always
test a small amount for chemical compatibility
before using and follow maintenance procedure.
•Vehicular traffic must pass over the protector slowly
and with caution.
MOUNTING INSTRUCTIONS FOR TEMPORARY USE
NOTE: Due to variables associated with
mounting, it is highly recommend you test the
hardware for each application
•Four through-holes with an inside diameter of .21" can
be used with either nails or screws (not included) for
temporary mounting of cable protector.
•Washer with a minimum outside diameter of .75"
should be used with each nail or screw.
•Through-holes have a threaded insert, but the
threaded insert is not designed for use with a bolt.
•When temporarily mounting on a sloped surface, the
hinge barrel must be on the uphill side of the slope.
•When temporarily mounting on a flat surface, the
hinge barrel must be facing the direction of traffic.
•To easily remove the protector when nailed down, use
a pry bar in the pry slots under each through-hole.
MAINTENANCE
•Store in a clean dry area.
•Inspect protector for damage and replace it if
damaged.
•Remove any foreign materials, solids and liquids.
•Keep clean by using a detergent and water solution.
INSTRUCTIONS CONTINUED
πCHICAGO•ATLANTA•DALLAS•LOSANGELES•MINNEAPOLIS•NYC/PHILA•SEATTLE•MEXICO•CANADA
1-800-295-5510
uline.com