UBCO 2X2 User manual

ubcobikes.com
[e-mail]
@ubcobikes #ubco2X2
1. Check your power supply is
suciently charged.
2. Ensure the battery strap and
plug are secured tightly.
3. Ensure the lights are
working: headlight, rear light,
brake light and directional
indicators.
4. Test the brakes & the horn
are functioning properly.
5. Adjust the rear view mirrors.
6. Check the tyre pressure;
inflate if needed.
7. Do a physical check to
ensure all nuts, bolts, and
fixings are tight and all loads
are secure.
8. Always wear a helmet and
appropriate clothing and
footwear.
Before you head out on your 2X2, always
check that your bike is ready to ride.
PRERIDE
CHECKLIST
2
6
3
4
7
5
1
UBCO 2X2 ADVENTURE BIKE

GET READY
AKeep the bike standing in the base to help align the handlebars. Remove the
protective packaging from the bike.
AFind the Field Kit under your seat and set out the tools you’ll need.
ANote: Remember to remove the guidance stickers after each step is completed.
3. Fit the mirrors
ARemove the mirrors from their box.
AScrew the base of the mirror arm
clockwise into the handlebar mount
approximately 10mm and into the correct
position, but do not tighten.
AUsing a 14mm spanner, tighten the
locking nut to secure the mirror arm.
ASlide down the rubber booty.
ARepeat for the other mirror.
AAdjust the mirror angle from a sitting
position to provide maximum visibility.
2. Fit the rear indicators (turn signals)
AUnpack the rear indicator lights.
AInstall indicators to their respective
side on the rear light bracket. Check
the orientation – the indicator with
a long cable is fitted to left side, the
short cable goes to right side.
AInsert the thread through the mount,
ensuring the nut and two washers
are on the inside. Lights should face
straight back. Use a 17mm spanner to
tighten the fastening nuts.
1. Align the handlebars
ALoosen the side bolts on the stem
with a 5mm Allen key. Straighten
the handlebars in line with the front
wheel and so the orange dots align.
AOnce the handlebars are
straight, re-tighten the stem bolts,
alternating as you go to prevent
damage to the clamp. Align the
marking on the bolt head to
achieve the correct tightness.
Torque to 15Nm, if available. 4a. Install the power supply
AIMPORTANT: inspect the power supply; contact UBCO if there is any damage from transit.
AIf the power supply is not already in place, remove the battery strap from the frame and set
aside. With the power socket on the right-hand side of the bike, carefully lower the power
supply into place with both hands.
APlug the bike’s power plug into the power socket. Use the securing key to lock the power
supply in place.
ASecure the battery strap as shown (4b).
V3.3
Left
bar
Power Supply
Right
bar
13
4
2
Power Plug
Lock
Power Supply
Power
Socket
KIA ORA
HELLO.
4b. Secure the battery strap
AVelcro side down, tuck the end of the battery strap under the left hand bar,
central to the power supply.
ACarry the strap over the power supply and tuck it under the right hand bar. Feed
the strap back through the clip and centre the clip.
ATighten the strap and secure it closed.
Scan this QR code to watch
our bike assembly video.
If you don’t feel confident
putting your bike together,
contact us for help.
READY TO RIDE
STEP 1:
Download the UBCO App
You can download the UBCO
App to view speed and battery
charge, control the settings
of your 2X2, and get critical
updates delivered wirelessly.
Simply search for UBCO in
your phone’s app store and
download it for free. Make sure
Bluetooth is activated on your
mobile phone when connecting
the app to your 2X2.
STEP 2:
Turn on the 2X2
Grab your keys and
power the bike by
pressing the button on
the key fob 1.5 seconds
until you hear a beep.
You can now open the
app and connect to
your bike.
See the complete
riding instructions in
the User Manual on
page 16.
STEP 3:
Check power supply charge
View the charge level on the LCD
display or on the Home and
Live Dash screens of the app.
Your power supply will arrive with
partial charge, enough to ride for a
few minutes. Be sure to fully charge up
before you plan a longer ride.
STEP 4:
Before you ride
Ensure you’ve read the user manual
and are familiar with how to use the
bike and proper safety precautions.
Always wear a helmet. Once you’re
ready to ride, twist the throttle and GO!!!
Find UBCO online:
ubcobikes.com
.com/ubcobikes
instagram.com/ubcobikes
youtube.com/ubcobikes
Join the UBCO Owners group for tips
and tricks from our community.
facebook.com/groups/ubcoowners
Key fob
Securing key
If your 2X2 has arrived in the box,
here’s how to set up your new ride.
Lift up the seat to find a Field Kit with all the tools
you need for assembly and some basic maintenance.
Scissors or a knife will also be handy and a torque
wrench, if you have one.