Ubiquiti BulletM2-HP User manual

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 1/12
Bullet M2 Compress  on Seal
Package Contents
Installat  on Requ  rements
Sh  elded Category 5 (or above) cabl  ng w  th dra  n w  re should be used for all
outdoor w  red Ethernet connect  ons and should be grounded through the AC
ground of the PoE.
We recommend that you protect your networks from harmful outdoor env  ronments
and destruct  ve ESD events w  th  ndustr  al-grade, sh  elded Ethernet cable from
Ub  qu  t  .. For more deta  ls, v  s  t u  .com/toughcable
Surge protect  on should be used for all outdoor  nstallat  ons. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP, one near the B-DB-AC and the
other at the entry po  nt to the bu  ld  ng. The ETH-SP w  ll absorb power surges and
safely d  scharge them  nto the ground.
* Shown w  thout antenna.
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com
all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 2/12
S  gnal LEDs
Hardware Overv  ew
In a  rOS®, you can mod  fy the threshold values for the w  reless s  gnal strength LEDs
on the Advanced tab under S  gnal LED Thresholds. The default values are shown
below:
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 3/12
Ethernet LED
Power LED
Reset Button
Ethernet Port
The Ethernet LED w  ll l  ght steady green when an act  ve Ethernet connect  on  s
made and ash when there  s act  v  ty.
The Power LED w  ll l  ght green when the dev  ce  s connected to a power source.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds wh  le the dev  ce  s powered on.
Th  s 10/100 Ethernet port  s used to connect the power and should be connected to
the LAN and DHCP server.
Hardware Installat  on
1.
2.
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 4/12
3.
4.
5.
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 5/12
6.
7.
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 6/12
Access  ng a  rOS
Ver  fy connect  v  ty  n the a  rOS® Conf  gurat  on Interface.
1. Make sure that your host mach  ne  s connected v  a Ethernet to the dev  ce.
2. Conf  gure the Ethernet adapter on your host system w  th a stat  c IP address on the
192.168.1.x subnet.
3. Launch your web browser and type https://192.168.1.20  n the address f  eld. Press
enter (PC) or return (Mac).
4. Enter ubnt  n the Username and Password f  elds. Select your Country and Language.
You must agree to the Terms of Use to use the product. Cl  ck Log  n.
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com
all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 7/12
The a  rOS Conf  gurat  on Interface w  ll appear, allow  ng you to custom  ze your sett  ngs
as needed. For add  t  onal deta  ls on the a  rOS Conf  gurat  on Interface, refer to the User
Gu  de ava  lable at: u  .com/download/a  rmax
You can also manage your dev  ce us  ng the Ub  qu  t  Network Management System.
Setup us  ng the UNMS™ app requ  res the U-Installer, sold separately.
Installer Compl  ance Respons  b  l  ty
Dev  ces must be profess  onally  nstalled and  t  s the profess  onal  nstaller’s
respons  b  l  ty to make sure the dev  ce  s operated w  th  n local country regulatory
requ  rements.
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 8/12
Antena
Select your antenna from the l  st. Ensure Calculate EIRP L  m  t  s enabled; transm  t
output power  s automat  cally adjusted to comply w  th the regulat  ons of the
appl  cable country. For a Custom antenna, Antenna Ga  n  s entered manually. Note the
requ  rements and antenna types l  sted below.
Cable Loss (When appl  cable)
Enter the cable loss  n dB. Output power  s adjusted to compensate for loss between
the rad  o and the antenna.
Cert  f  ed Antenna Types
Th  s rad  o transm  tter FCC ID: FCC: SWX-M2BW / IC: 6545A-M2BW has been approved
by FCC / ISED Canada to operate w  th the antenna types l  sted below w  th the
max  mum perm  ss  ble ga  n for each antenna type  nd  cated. Antenna types not
 ncluded  n th  s l  st or hav  ng a ga  n greater than the max  mum ga  n  nd  cated for that
type, are str  ctly proh  b  ted for use w  th th  s dev  ce.
Antenna Frequency Ga  n
Omn  2.4 GHz 13 dB 
Sector 2.4 GHz 17 dB 
D  sh 2.4 GHz 24 dB 
Spec  f  cat  ons
BulletM2-HP
D  mens  ons 163.65 x 38.75 x 38.75 mm
(7.48 x 1.53 x 1.53")
We  ght 130 g (4.59 oz)
Enclosure Polycarbonate
Network  ng Interface 10/100 Mbps
Antenna Connector N-Type Connector
LEDs Power, Ethernet,
(4) S  gnal Strength
Max. Power Consumpt  on 7W
Output Power 25 dBm
Power Supply AC to 24VDC, 0.5A G  gab  t PoE Adapter
Power Method 24V Pass  ve PoE
(Pa  rs 4, 5+; 7, 8-)
ESD/EMP Protect  on ± 24 kV Contact/A  r
Operat  ng Temperature -40 to 70° C (-40 to 158° F)
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 9/12
BulletM2-HP
Operat  ng Hum  d  ty 5 to 95% Condens  ng
Shock and V  brat  on ETSI300-019-1.4
Cert  f  cat  ons CE, FCC, IC
Operat  ng Frequency (MHz)
US/CA 2412 - 2462
Worldw  de 2412 - 2472
Safety Not  ces
1. Read, follow, and keep these  nstruct  ons.
2. Heed all warn  ngs.
3. Only use attachments/accessor  es spec  f  ed by the manufacturer.
WARNING: Do not use th  s product  n locat  on that can be submerged by water.
WARNING: Avo  d us  ng th  s product dur  ng an electr  cal storm. There may be a remote
r  sk of electr  c shock from l  ghtn  ng.
Electr  cal Safety Informat  on
1. Compl  ance  s requ  red w  th respect to voltage, frequency, and current requ  rements  nd  cated
on the manufacturer’s label. Connect  on to a d  fferent power source than those spec  f  ed may
result  n  mproper operat  on, damage to the equ  pment or pose a f  re hazard  f the l  m  tat  ons
are not followed.
2. There are no operator serv  ceable parts  ns  de th  s equ  pment. Serv  ce should be prov  ded only
by a qual  f  ed serv  ce techn  c  an.
L  m  ted Warranty
u  .com/support/warranty
The l  m  ted warranty requ  res the use of arb  trat  on to resolve d  sputes on an  nd  v  dual bas  s, and,
where appl  cable, spec  fy arb  trat  on  nstead of jury tr  als or class act  ons.
Compl  ance
FCC
Changes or mod  f  cat  ons not expressly approved by the party respons  ble for compl  ance could
vo  d the user’s author  ty to operate the equ  pment.
Th  s dev  ce compl  es w  th Part 15 of the FCC Rules. Operat  on  s subject to the follow  ng two
cond  t  ons.
1. Th  s dev  ce may not cause harmful  nterference, and
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com

17.02.2020 BulletM2-HP Quck Start Gude
https://dl.ubnt.com/qsg/BulletM2-HP/BulletM2-HP_EN.html 10/12
2. Th  s dev  ce must accept any  nterference rece  ved,  nclud  ng  nterference that may cause
undes  red operat  on.
Th  s equ  pment has been tested and found to comply w  th the l  m  ts for a Class A d  g  tal dev  ce,
pursuant to part 15 of the FCC Rules. These l  m  ts are des  gned to prov  de reasonable protect  on
aga  nst harmful  nterference when the equ  pment  s operated  n a commerc  al env  ronment. Th  s
equ  pment generates, uses, and can rad  ate rad  o frequency energy and,  f not  nstalled and used
 n accordance w  th the  nstruct  on manual, may cause harmful  nterference to rad  o
commun  cat  ons. Operat  ons of th  s equ  pment  n a res  dent  al area  s l  kely to cause harmful
 nterference  n wh  ch case the user w  ll be requ  red to correct the  nterference at h  s own expense.
Th  s rad  o transm  tter has been approved by FCC.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
Th  s dev  ce compl  es w  th ISED Canada l  cence-exempt RSS standard(s). Operat  on  s subject to the
follow  ng two cond  t  ons:
1. Th  s dev  ce may not cause  nterference, and
2. Th  s dev  ce must accept any  nterference,  nclud  ng  nterference that may cause undes  red
operat  on of the dev  ce.
Th  s rad  o transm  tter has been approved by ISED Canada.
The dev  ce for operat  on  n the band 5150-5250 MHz  s only for  ndoor use to reduce the potent  al
for harmful  nterference to co-channel mob  le satell  te systems.
CAN ICES-3(A)/NMB-3(A)
Le présent appare  l est conforme aux CNR d’ISDE Canada appl  cables aux appare  ls rad  o exempts
de l  cence. L’explo  tat  on est autor  sée aux deux cond  t  ons su  vantes :
1. l’appare  l ne do  t pas produ  re de brou  llage;
2. l’appare  l do  t accepter tout brou  llage rad  oélectr  que sub  , même s  le brou  llage est
suscept  ble d’en compromettre le fonct  onnement.
Le présent émetteur rad  o a été approuvé par ISDE Canada.
Les d  spos  t  fs fonct  onnant dans la bande 5150-5250 MHz sont réservés un  quement pour une
ut  l  sat  on à l’  ntér  eur af  n de rédu  re les r  sques de brou  llage préjud  c  able aux systèmes de
satell  tes mob  les ut  l  sant les mêmes canaux.
IMPORTANT NOTE
Rad  at  on Exposure Statement
Th  s equ  pment compl  es w  th rad  at  on exposure l  m  ts set forth for an uncontrolled
env  ronment.
Th  s equ  pment should be  nstalled and operated w  th m  n  mum d  stance 20 cm between the
rad  ator and your body.
Th  s transm  tter must not be co-located or operat  ng  n conjunct  on w  th any other antenna or
transm  tter.
AVIS IMPORTANT
Déclarat  on sur l’expos  t  on aux rayonnements
BulletM2-HP Qu  ck Start Gu  de
All manuals and user guides at all-guidesbox.com