Ultimate Support MC-125 User manual

Visit www.ultimatesupport.com, click on Music Gear and Instrument Stands/Customer
Support/Warranty Registration. This is a quick and convenient process for registering your
new Ultimate Support product. Warranty Registration and Proof of Purchase are required
for warranty fulfillment.
Warranty Information
In its commitment to uncompromising product quality, Ultimate Support provides
warranties on all products. There is a Five Year Limited Warranty on MC-125 Professional
Studio Boom Stand (#16124), This Limited Warranty is to the original user/purchaser of
Ultimate Support products. Ultimate Support warrants these products to be free from
manufacturing defects. This warranty does not include damage to the product resulting
from accident, misuse, improper installation or operation, unauthorized repair or alter-
ations. If the product should become defective within the warranty provisions, we will elect
to repair or replace it free of charge at our option, including free return postage, provided
it is delivered prepaid to Ultimate Support. Proof of purchase must be submitted with the
returned product.
THE PURCHASER’S/USER’S SOLE REMEDY SHALL BE SUCH REPAIR OR REPLACE-
MENT AS IS EXPRESSLY PROVIDED ABOVE, AND ULTIMATE SUPPORT SYSTEMS, INC.
SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT FOR ANY
PURPOSE WHATSOEVER.
For answers to any questions regarding warranty/service, call Customer Support
800-525-5628. Please visit www.ultimatesupport.com to register your product warranty
online.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, you may also have other rights which vary from state to state.
2506 Zurich Drive
Ft. Collins, CO 80524
Phone: [phone]
www.ultimatesupport.com
Product Manual for
Ultimate Support MC-125
Professional Studio Boom stand
(#16124)
Copyright 2005, Ultimate Support Systems, Inc.
All Rights Reserved. Revision 3, 12/12/2005
Product Manual Item #16316
Warranty Registration
Elevating Performances
4

Assembly Instructions User Instructions
STEP 1 - Casters:
Unlock to move the stand on the smooth-
rolling casters. Lock in place (1).
STEP 2 - Height Adjustment:
Loosen the upright clutch (2) by turning coun-
terclockwise. Adjust to your desired height.
Tighten the clutch by turning clockwise.
STEP 3 - Boom Length Adjustment:
Loosen the clutch (3) by turning counterclock-
wise. Adjust to your desired length. Tighten
the clutch by turning clockwise.
STEP 4- Boom Positioning:
The boom has 3-way adjustment: front-to-
back, up-and-down, and rotationally.
Simply loosen the control knob (4), make
all three adjustments and tighten snugly.
STEP 5- Counterweight:
For optimum balance, the boom counter-
weight (5a) can be repositioned. Simply
unscrew the two halves of the counter-
weight, position (5b) along the boom
portion of the stand and tighten.
STEP 6 - Boom Extension:
Set boom extension to vertical or hanging
straight down (see figure 4, page 2).
Securely tighten. Attach microphone.
STEP 7 - Cable Management:
Easy-to-use cable management clips (6) are
conveniently located in 2 places along the
boom and on the upright portion of the stand.
Simply press your mic cable into the clip for a
clean look. Gently pull the cable to remove.
mc-125 specs
• item #16124 - black
• stand height with casters 51 ½" - 82 ¾"
(1308 mm - 2102 mm)
• boom length 28” - 55” (711 mm - 1397 mm),
plus 5 ½” 140 mm) arm extension
•total stand weight 35 lbs. (15.88 kg)
•base weight with casters 22 ½ lbs. (10.2 kg)
•base diameter 22 ½” (572 mm)
•caster diameter 3" (76 mm)
•caster assembly height 3 ¾” (95 mm)
•load capacity 5 lbs. (2.3 kg)
•counterweight weight 5 ¾ lbs. (2.6 kg)
•folded assembled with casters 58 ¾" x 22 ½"
(1492 mm x 508 mm)
• 5-year warranty:
see
Warranty Information section, pg. 4, for details
Threaded
Caster
Threaded
Corner
Threaded
Base
Boom
Extension
STEP 1 - Attaching Swivel Casters:
Put caster into “Lock” position (1a). Screw
all three swivel casters into the threaded
corners on the underside of the base (1b).
Securely tighten.
STEP 2 - Attaching Upright Shaft:
Thread upright assembly securely into the
base (2).
STEP 3 - Attaching Boom:
Thread the boom portion of the stand onto
the top of the upright shaft (3). Securely
tighten.
STEP 4 - Attaching Boom Extension:
Screw the boom extension onto the
threaded end of the main boom portion of
the stand (4).
Caster
with
Lock
Upright
Clutch
2
3
Boom
Clutch
3
4
1b
2
1a 1
Wheel
Lock
Boom
on
Upright
Boom
Adjustment
Knob
5b
6
Cable
Management
Clip
4
5a
Counter-
weight
2 3