Unfinished Furniture of Wilmington SH-3228A User manual

ITEM NO. : SH-3228A
REVISED MAY 17, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 32 X 12 X 84 HIGH BOOK CASE RTA
: SH-3228A

ITEM NO. : SH-3228A
REVISED MAY 17, 2016
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
-Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO. : SH-3228A
REVISED MAY 17, 2016
Printed in Vietnam
- 3 -
PARTS LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Side panel
(L-R)
2
C
Bottom panel
1
D
Shelf panel
2
E
Adjustable
shelf
4
F
Back
upper
1
G
Back center
1
H
Back lower
1
I
Connecter
1

ITEM NO. : SH-3228A
REVISED MAY 17, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 30mm)
16
2
Small Flat washer
(6.5 x13mm)
16
3
Lock washer
(6.5x11mm)
16
4
Allen Key
(M4 x 30mm x 120mm)
1
5
Bracket
16
6
Short screw
(M3.5 x15mm)
20
7
Long screw
(M4 x 30mm)
2
8
Steel band
2
9
Pan head screw
(M4 x 20mm)
16
10
Large Flat washer
(6.5 x19mm)
8
STEP 1
Attach side panels (B) to the top (A), and shelf panels (D) and bottom panel (C) with bolts (1), and
washers (3) and (2) as shown below. Tighten with Allen key (4).

ITEM NO. : SH-3228A
REVISED MAY 17, 2016
Printed in Vietnam
- 5 -
STEP 2
Slide back panels (F), and (G) and (H) into the grooves of side panels (B) and top (A) as shown below.
Attach back panel (H) to bottom panel (C) with pan head screws (9) as shown below. Then attach
back panels (H), and (G) and (F) to shelf panels (D) with pan head screws (9) and washers (10).
Tighten with a screwdriver.
Remove the paper strip and attach sticky side of connecters (I) to back of the unit. Then attach
connecter (I) to the top (A), and bottom panel (C) and shelf panels (D) with pan head screws (9).
Tighten with a screwdriver.

ITEM NO. : SH-3228A
REVISED MAY 17, 2016
Printed in Vietnam
- 6 -
STEP 3
Attach brackets (5) to the unit as shown below. Then place the shelves (E) on the brackets and
attach with screws (6). Tighten with the screwdriver.
Attach steel band (8) to the unit with screws (6) and attach steel band (8) to a wall with screws (7) as
shown below (to secure the product and prevent tipping). Tighten with a screwdriver.