Unfinished Furniture of Wilmington TV-49 User manual

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: CORNER ENTERTAINMENT CENTER
: TV-49

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.
.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
H
Center
Shelf
1
B
Bottom
panel
1
I
Center
panel
1
C
Side panel
(L - R)
2
J
Side shelf
4
D
Vertical
panel
(L-R)
2
K
Drawer
front
1
E
Support leg
1
L
Drawer
side (L-R)
2
F
Center
back panel
1
M
Drawer
back
1
G
Side back
panel
2
N
Drawer
bottom
1

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6x35mm)
22
8
Long screw
(M4 x 30mm)
9
2
Spring washer
(6.5x11mm)
22
9
Short pan head
screw
(3x15mm)
3
3
Flat washer
(6.5x19mm)
12
10
Shelf support
bracket
20
4
Flat washer
(6.5x13mm)
10
11
Steel band
1
5
Wooden knob
(38x30mm)
1
12
Warning label
1
6
Long pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
1
13
Screw
(M3.5 x 15mm)
26
7
Allen key
(M4 x 80mm)
1
14
L-bracket
2
METAL KNOB
(30x30mm)
GOES WITH
FINISHED ITEM
ONLY.
1
STEP 1
Attach side panels (C) to the top (A) with bolts (1), washers (2) and (3) as shown below. Tighten with
Allen key (7).

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 5 -
STEP 2
Attach center panel (I) to vertical panels (D) with bolts (1) and washers (2) and (4) as shown below.
Tighten with Allen key (7).
Attach vertical panels (D) to the top (A) with bolts (1) and washers (2) and (3) as shown below.
Tighten with Allen key (7).
STEP 3
Slide center back panel (F) and side back panel (G) into to the grooves as shown below.

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 6 -
STEP 4
Attach bottom panel (B) to vertical panels (D) with bolts (1) and washers (2) and (4) as shown below.
Tighten with Allen key (7).
TEP 4
STEP 5
Attach bottom panel (B) to side panels (C) with bolts (1) and washers (2) and (3) as shown below.
Attach support leg (E) to vertical panels (D) with bolts (1) and washers (2) and (4) as shown below.
Tighten with Allen key (7).

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 7 -
STEP 6
Attach center back panel (F) to top (A) with pan head screws (9) as shown below. Tighten with the
screwdriver.
Attach top (A) to vertical panel (D) with (L) - brackets (14) and screws (13) as shown below. Tighten
with the screwdriver.
STEP 7
Attach a drawer side (L) to drawer front (K) and drawer back (M) with screws (8). Tighten with the
screw driver.
Insert drawer bottom (N) into the grooves at bottom of drawer side (L), drawer front (K) and drawer
back (M).
Attach the other drawer side (L) to the drawer front (K), drawer back (M) with screws (8). Tighten with
the screw driver.
Attach knob (5) to drawer front (K) with screw (6). Tighten with the screwdriver.

ITEM NO.: TV-49
REVISED JAN 13, 2016
Printed in Vietnam
- 8 -
STEP 8
Carefully insert the drawer (from Step 7) into the unit.
Stick the warning labels (12) into the drawer before use. Insert the brackets (10) into the unit and then
place shelves (J) and (H) on the brackets.
Attach steel band (11) to the unit with screws (13). Then attach the steel band to a wall with screws
(8) as shown below (to secure the product and prevent tipping).
8