Unfinished Furniture of Wilmington SH-7230X User manual

ITEM NO : SH-7230X
REVISED MAR 09, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: X-SIDE SHELVES 72 H X 30 W
: SH-7230X

ITEM NO : SH-7230X
REVISED MAR 09, 2016
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO : SH-7230X
REVISED MAR 09, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Fixed shelf
3
C
Adjustable
shelf
2
D
Side frame
(L-R)
2
E
Rail
8
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
bolt
(M6x30mm)
16
2
Flat Washer
(ɸ6.5x13mm)
16
3
Lock Washer
(ɸ6.5x11mm)
16
4
Allen Key
(M4x80mm)
1
5
Long Screw
(M4x30mm)
25
6
Short Screw
(M3.5x15mm)
10
7
Bracket
8
8
Steel band
1

ITEM NO : SH-7230X
REVISED MAR 09, 2016
Printed in Vietnam
- 4 -
STEP 1
Attach shelves (B) and top (A) to the side frame (D) with bolts (1), and washers (2) and (3) as shown
bellow. Tighten with Allen key (4).It
STEP 2
Insert rails (E) into side frames (D) as shown below. Then attach other side frame (D) to the unit with
bolts (1), and washers (2) and (3). Tighten with Allen key (4).

ITEM NO : SH-7230X
REVISED MAR 09, 2016
Printed in Vietnam
- 5 -
STEP 3
Attach rails (E) to top (A) and shelves (B) with screws (5) as shown below. Tighten with a screwdriver.
STEP 4
Attach brackets (7) to the unit. Place the adjustable shelves (C) on the brackets and attach with
screws (6) as shown below. Tighten with a screwdriver.
Attach the steel band (8) to the unit with screws (6). Then attach the steel band to the wall with screw
(5) as shown below (to secure the product and prevent tipping).