Unfinished Furniture of Wilmington SV-38A User manual

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: BARN DOOR SERVER
:
SV-38A AND SV-38B

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
-Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST SV-38A
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top 1
B
Bottom panel
1
C
Side Shelf
(L-R) 4
D
Center Shelf 1
E
Drawer front
1
F
Drawer side
(L-R) 2
G
Drawer back
1
H
Drawer bottom
1
I
Support bar 2

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
PART LIST SV-38B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
J
Vertical panel
(L-R) 2
K
Side panel
(L-R) 2
L
Side Back panel
2
M
Center B
ack
panel 1
N
Door (L-R) 2

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm) 16
2
Lock Washer
(Æ6.5 x 11mm) 16
3
Flat Washer
(Æ6.5 x 19mm) 16
4
Screw
(M3.5 x 15mm) 20
5
Short Screw
(M3.5 x 15mm) 24
6
Long Screw
(M4 x 35mm) 18
7
Shelf support
bracket
20
8
Door roller
(3 x 30
mm x 120mm)
4
9
Handle
(2 x 25mm x 180mm)
2
10
Washer 4
11
Pan screw
(M8 x 20mm) 4
12
Steel band
2
13
Allen Key
(M4x 30mm x 110mm
)
1
14
Wrench
(13mm) 1
NOTE: HARDWARE IS PACKED IN CARTON SV-38B.

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 6 -
STEP 1
Attach vertical panels (J) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten
with Allen key (13).
STEP 2
Attach bottom panel (B) to vertical panels (J) with bolts (1), and washers (2) and (3) as shown below.
Tighten with Allen key (13).
Attach door rollers (8) to top (A) as shown below.

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 7 -
STEP 3
Attach side panels (K) to bottom panel (B) and top (A) with bolts (1), and washers (2) and (3) as
shown below. Tighten with Allen key (13).
Attach the steel rail of top (A) to side panels (K) with screws (4) as shown below. Tighten with a
screwdriver.
STEP 4
Slide back panels (M) and (L) into the grooves as shown below. Then attach back panels (M) and (L)
to bottom panel (B) with screws (4) as shown below. Tighten with a screwdriver.

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 8 -
STEP 5
Attach drawer sides (F) to drawer front (E) with screws (6) as shown below. Tighten with a screwdriver.
Insert drawer bottom (H) into the grooves at bottom of drawer sides (F) and drawer front (E) as shown
below.
Attach drawer back (G) to drawer sides (F) with screws (6) as shown below. Tighten with a screwdriver.
Attach support bars (I) to bottom drawer (H) with screws (6) as shown below. Tighten with a screwdriver.
STEP 6
Carefully put the drawer into the unit.
Insert brackets (7) into the unit as shown below. Place shelves (C) and (D) on the brackets and attach
with screws (5). Tighten with a screwdriver.

ITEM NO.: SV-38 AND SV-38B
ISSUED DEC 20, 2017
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 9 -
STEP 7
Attach door rollers (8) to doors (N) with screws (4) as shown below. Tighten with a screwdriver.
Attach handles (9) to doors (N) with screws (11) and washers (10) as shown below. Tighten with
wrench (14).
STEP 8
Attach steel bands (12) to the unit with screws (5) and attach the steel bands to the wall with screws
(6) as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.