Unfinished Furniture of Wilmington VISTA B-14A User manual

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: VISTA 3-DOOR BUFFET
: B-14A AND B-14B

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
-Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST B-14A
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Bottom panel
1
C
Side Bottom
Shelf
(L-R)
2
D
Center
Bottom Shelf
1
E
Side Shelf
(L-R)
2
F
Center Shelf
1
NOTE: WARNING LABEL (INCLUDED)

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
PART LIST B-14B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
G
Side panel
(L-R)
2
H
Vertical panel
(L-R)
2
I
Front Leg
(L-R)
2
J
Back Leg
(L-R)
2
K
Side Back
panel
2
L
Center Back
panel
1
M
Door
(02L-01R)
3

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Short Bolt
(M6 x 35mm)
20
2
Small Lock Washer
(6.5 x 11mm)
20
3
Small Flat Washer
(6.5 x 19mm)
20
4
Long bolt
(M8 x 40mm)
4
5
Large Lock Washer
(8.5 x13mm)
4
6
Large Flat Washer
(8.5 x19mm)
4
7
Short Pan head screw
(M3.5 x 15mm)
28
8
Short Screw
(M3.5 x 15mm)
18
9
Long Screw
(M4 x 35mm)
2
10
Shelf support
bracket
12
11
Wooden Knob
(35 x 35mm)
6
12
Long Pan head screw
(M4 x 25mm)
6
13
Steel band
2
14
Magnet
3
15
Allen key
(M4 x 30mm x 110mm)
1
16
Short Pan head screw
(M3 x 15mm)
6
NOTE: HARDWARE IS PACKED IN CARTON B-14B.

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 6 -
STEP 1
Attach front legs (I), and back legs (J) to bottom panel (B) with bolts (4), and washers (5) and (6) as
shown below. Tighten with Allen key (15).
STEP 2
Pull out the drawers. Then attach side panels (G) to top (A) with bolts (1), and washers (2) and (3) as
shown below. Tighten with Allen key (15).

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 7 -
STEP 3
Attach vertical panels (H) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten
with Allen key (15).
STEP 4
Attach bottom panel (B) to side panels (G) and vertical panels (H) with bolts (1), and washers (2) and
(3) as shown below. Tighten with Allen key (15).

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 8 -
STEP 5
Slide back panels (K) and (L) into the grooves as shown below, and then attach back panels (K) and
(L) to bottom panel (B) and top (A) with screws (7). Tighten with a screwdriver.
STEP 6
Attach doors (M) to side panels (G), and vertical panel (H) with screws (8) as shown below. Tighten
with a screwdriver.
Attach magnets (14) to the unit with screws (16) as shown below. Tighten with a screwdriver.

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 9 -
STEP 7
Put bottom shelves (C) and (D) into the unit as shown below.
STEP 8
Insert brackets (10) into the unit as shown below. Place shelves (E) and (F) on the brackets and
attach with screws (7). Tighten with a screwdriver.

ITEM NO.: B-14A AND B-14B
ISSUED JUN 17, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 10 -
STEP 9
Attach knobs (11) to and front of drawers and doors with pan head screws (12) as shown below.
Tighten with a screwdriver.
Attach steel bands (13) to the unit with screws (7) as shown below.
(to secure the product to the wall and reduce the risk of tipping over).
Important!
Properly attach steel bands (13) to the wall in an area of drywall or plaster with a wood stud:
Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood
stud(s) in the wall.
Drill 1/8-inch (3mm) diameter hole(s) into the wood stud(s) located in the wall, where you marked
with the pencil.
Properly attach steel bands to the wall with screws (9) and tighten screw(s) firmly into the wall.