Unicol GKUX User manual

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your
carrier claims agent and do not continue the installation until it has been reviewed. Please watch for
pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface will support five times the
combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also
layout all components to ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified use may result in failure or
personal injury. This product is intended for indoor use only. We recommend using a qualified trades
person for installation. Use an assistant or lifting equipment to lift and position products.
For support, please call: [phone] or email: [email protected]
Revised 15/09/22
01865 767676
[email protected]
www.unicol.com
*Please check model specific details before installing*
GKUX / GKU1 / GKU2 / GKU3
GKUT1 / GKUT3 / KPR KITS
Guide Max. Weight: 12kg

01865 767676
[email protected]
www.unicol.com
2Revised 15/09/22
COMPONENTS
INSTALLERS REQUIRED
1
# DESCRIPTION QTY
1GKU1 Ceiling Fixing Plate & Arm 1
2GKU1 Projector Fixing Plate & Arm 1
3
4
5
6
7
8
9
10
#TOOLS REQUIRED
1 5mm Allen Key
2
3
4
5
12
NOTE:
GKUX is a close to ceiling version of the GKU1 and
has no telescopic arm.
GKU2 is a GKU1 and comes with a separate
extension arm to increase arm length if required.
GKU3 comes complete with a long telescopic arm.
GK0 is a camera screw version for projectors with a
single camera screw receptacle.
Follow these instructions for each of the models
above.

01865 767676
[email protected]
www.unicol.com
3
Revised 15/09/22
STEP 1
Using the 4 mounting slots cut out on the ceiling
plate, determine where you want to install, mark it
and fix into position. If fixing to a slanted ceiling,
adjust the angle of the body by loosening the
screws at the side, levelling and tightening again.
Please consider cabling and fixings prior to
installation. Please check surface can support 5x
the combined solutions weight.
STEP 2
Fix the Universal plate and telescopic section to
the projector using the screws provided. Adjust
arm lengths (2) by loosening the knurled screws
(3) to enable fixing screws to locate into projector
fixing holes. Level the Universal plate against
the projector by screwing up or down the hollow
screws (1). Once in position, centralise the mount
and tighten all screws.
STEP 3
Join the 2 parts of the GKU1 together by sliding the
bottom half into the top half and fix using the dome
headed allen screws. Adjust the telescopic section
as required and fully tighten screws.
STEP 4
Using the pan, tilt and screen levelling functions
adjust the projector alignment. Finally tighten all
dome headed screws using the allen key provided.
1
2
3
STANDARD

4
01865 767676
[email protected]
www.unicol.com
Revised 15/09/22
STEP 1
Loosen the truss clamp to open it up. Place around
the truss, close the clamp and tighten until secure.
Please consider cabling and fixings prior to
installation. Please check surface can support 5x
the combined solutions weight.
Please carry on with Step 2 on page 3.
STEP 1
Using the 4 ceiling mounting slots, as shown
above, determine where you want to install your
mount, mark it and fix into position.
Please consider cabling and ceiling fixings prior to
installation. Please check surface is capable of
supporting 5x the combined solutions weight.
STEP 2
Slide all cabling through the column and through
the gap in the ceiling plate socket. Being mindful
of the cables, slide the column into the socket,
ensuring that the two holes either side align with
those on the mount. Using the through bolt, secure
the column into place and tighten the two grub
screws at the rear. Follow Step 2 on page 3.
STEP 3
Slide the mount adapter into the bottom of the
column and secure on either side of the column
using the dome headed screws provided.
Carry on with Step 4 on page 3.
TRUSS MOUNTED COLUMN MOUNTED