Unicol TCAVT User manual

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your
carrier claims agent and do not continue the installation until it has been reviewed. Please watch for
pinch points. Do not put your ngers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface will support ve times the
combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also
layout all components to ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specied use may result in failure or
personal injury. This product is intended for indoor use only. We recommend using a qualied trades
person for installation. Use an assistant or lifting equipment to lift and position products.
Revised 24/07/21
01865 767676
[email protected]
www.unicol.com
*Please check model specic details before installing*
TCAVT
Screen Size: 70-100” Guide Max. Weight: 120kg

01865 767676
[email protected]
www.unicol.com
2Revised 24/07/21
COMPONENTS
INSTALLERS REQUIRED
1-2
# DESCRIPTION QTY
1TCAVTB Trolley Base 1
21650 Columns 2
3TCAVTG Mount Adapter 1
4PZX9 Screen Mount - Back Plate 1
5PZX9 Screen Mount - Mounting Arms 2
6Optional Accessory – TCAVS Shelf -
7Optional Accessory – TCVLC Cabinet -
#TOOLS REQUIRED
1 3/16th Allen Key
2 Pozidrive Screwdriver
3 17mm Spanner
1
2
3
4 5
6 7

01865 767676
[email protected]
www.unicol.com
3
Revised 24/07/21
STEP 1
Place trolley base on a at surface and apply
brakes by pressing down levers on each castor.
Loosen the grub screws on the back of socket
upstands and place a column in each socket.
Tighten grub screws until they just touch columns.
Do not tighten fully. Thread power and signal
cables through base sockets and columns.
NOTE: If tting an accessory, please see page 4.
STEP 2
Loosen grub screws in mount adapter sockets.
Place over the columns and thread cables through.
Column edges should be level with the tops of the
top socket caps. Tighten grub screws so they just
stop the adapter from sliding down the columns.
Tighten all grub screws (base and mount adapter).
STEP 3
Fit the PZX9 backplate to the mount adapter.
Secure into the backplate rivnuts with the 4 x M10
x 25 hex-head screws through the 300 x 300 xing
holes in the mount adapter. Thread cables through
central apertures in mount adapter and back plate.
STEP 4
Using the griplock (top) and taglock (bottom)
spacers x the mount arms to the screen
xing holes. Choose the correct manufacture
recommended xing screws for your screen from
the universal xing pack supplied.

4
01865 767676
[email protected]
www.unicol.com
Revised 24/07/21
STEP 5
Using another team member, lift the screen up and
gradually oer it up to the back plate. Gently tilting
the screen forward, hook the arms over the lip of
the back plate rail and lower once in position.
Centre the screen horizontally by sliding from side
to side until you are happy with the position.
STEP 6
Once centered, ensure the bottom screws are not
tightly xed and screw down the top screws to level
the screen. Once level tighten bottom screws to
secure the mount. Connect cables to screen.
NOTE: The screen position cannot be adjusted after
the bottom screws have been tightened.
STEP 8 (OPTIONAL)
If tting the optional cabinet perform this before
Step 1.
Place on trolley base between sockets. Open
door and align xing holes in cabinet base with
corresponding rivnuts in trolley base. Using the 4 x
M10 x 25 hex-head screws provided x cabinet to
trolley base.
STEP 7 (OPTIONAL)
If tting the optional shelf perform this after Step 1.
Loosen the grub screws in the shelf sockets and
place over the columns. Allow shelf to rest on the
trolley base for now. Do not tighten grub screws.
After Step 2 adjust height of shelf and tighten grub
screws.
ACCESSORIES