Unicol AVHT User manual
WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your
carrier claims agent and do not continue the installation until it has been reviewed. Please watch for
pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface will support five times the
combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also
layout all components to ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified use may result in failure or
personal injury. This product is intended for indoor use only. We recommend using a qualified trades
person for installation. Use an assistant or lifting equipment to lift and position products.
Revised 15/12/20
01865 767676
www.unicol.com
*Please check model specific details before installing*
AVHT / AVHP / AVLT / AVLP / AVHB / AVHW
Screen Size: 33 - 70” Guide Max. Weight: 60-70kg
01865 767676
www.unicol.com
2Revised 15/12/20
COMPONENTS
INSTALLERS REQUIRED
1-2
#TOOLS REQUIRED
1 Pozi Head Screwdriver
2 17mm Spanner
3 5mm Allen Key
4 3/16th Allen Key
5
6
7
4
2
1
3
8 9
12
# DESCRIPTION QTY
11500mm (High) or 950mm (Low) Columns 2
2AVP1 500x400mm Shelf 1
3Twin Column Mount Adapter 1
47.5cm Castors (2 standard, 2 braked) 4
5Universal Mount Back Plate 1
6Universal Mount Arms 2
7Avecta Trolley Base 1
830cm Mast Front In-Fill Panel 2
930cm Mast Rear In-Fill Panel 2
10 15cm Mast Front In-Fill Panel 4
11 15cm Mast Rear In-Fill Panel 4
12 Alternative Bases -
13 Alternative Accessories
10 11
01865 767676
www.unicol.com
3
Revised 15/12/20
STEP 1
Turn the base upside down and push each castor
until it clicks into place. Please ensure that the
castors with brakes are located at the front. Place
base on the floor and apply brakes on front
wheels by pressing brake lever down.
See last page for other base options
STEP 2
Place the 2 columns with holes, located approx
75mm from the bottom, over the
crocodile lugs on the base.
STEP 3
Ensure that the holes line up with the grub screws
at the rear of the crocodile lugs. Leave the grub
screws loose for now.
STEP 4
Place the column adapter over the top of the two
columns (ensuring the grub screws are on the
same side as the rear of the base).
4
01865 767676
www.unicol.com
Revised 15/12/20
STEP 5
Once placed over columns and at the desired
height, tighten the two grub screws to secure into
place. Tighten up the base grub screws to secure.
STEP 6
Line the back plate up with the mount adapter,
as shown above. Fix 4 screws from behind the
mount adapter and into the 4 rivet nuts located on
the back plate. Ensure back plate is secure and
screws are tightened.
STEP 7
Locate the mounting holes on the back of your
screen. Line the two mounting arms up and using
the tag locks and manufacturer recommended
screws (included in fixing kit), attach the arms to
the back of the screen.
STEP 8
Line the screen and arms up with the secured back
plate and offer it up at a slight angle - allowing the
top of the arms to hook over the lip of the back
plate.
01865 767676
www.unicol.com
5
Revised 15/12/20
STEP 9
Gently lower the screen until the arms are securely
hanging on top of the back plate. Once centered,
adjust the level of the screen with the two top
screws on the mount arms. Once leveled secure
the screen by tightening the bottom two screws.
STEP 10
Identify the front mast in-fill panels (the 4 with cut-
outs go to the rear). Start with the panel that has
the 4-way power socket attached clip into place.
Cable up.
STEP 11 [OPTIONAL]
If fitting a shelf, choose the height you’d like and
insert between the panels as you’re clipping them
into position.
To insert, angle the shelf as you offer it up to the
columns. Level out and rest it in position. Unlike the
infill panels, the shelf does not clip into place.
STEP 12
Identify remaining mast in-fill panels. Start from
the bottom and clip 2 of the 3 larger rear panels in,
threading cabling through where necessary.
6
01865 767676
www.unicol.com
Revised 15/12/20
STEP 1a
Position floor plate and mark through the screw
holes (arrows above) where it will be positioned.
Before you screw through, ensure any cables
that are going underneath the plate are threaded
through the column grips (circled above).
STEP 2a
Loosen the grub screws on the jaws of the column
grips so that you can slide the columns over.
When sliding over, ensuring that any cables are not
caught.
Leave loose for now - follow on with Step 4.
STEP 1b
Position floor plate and mark through the screw
holes (arrows above) where it will be positioned
against a wall and fix in place.
Loosen the grub screws on the jaws of the column
grips so that you can slide the columns over
(circled abve).
STEP 2b
Before fixing the top plate into position, slide the
twin column mount adapter over the columns. This
can be height adjusted throughout the installation.
Loosen the grub screws on the column grips on
the top wall plate and place into columns. Mark
through the screw holes and fix into place against a
wall. Follow on from Step 6.
BOLT DOWN
FLOOR-TO-WALL
This manual suits for next models
5
Table of contents
Other Unicol TV Mount manuals
