Uniden DECT 6015 User manual

i
DECT 6005
Accessory handset for
DECT 6015 and DECT 6035 Series
DECT6005 OM.indd iDECT6005 OM.indd i 20/8/07 1:49:18 PM20/8/07 1:49:18 PM

1
Welcome
Congratulations on your purchase of the Uniden DECT6005
accessory handset and charger. You can place this fully featured
cordless handset anywhere your home has AC power.
Note: Illustrations in this manual are used for explanation
purposes. Some illustrations may differ from the actual unit.
Important!
The DECT6005 accessory handset will not operate until it is
registered to a Uniden main base. This manual describes how
to set up your new handset; for more detailed instructions on
operating your new handset, please refer to the manual supplied
with your base.
Terminology Used in this Manual
Base The main part of the phone that connects to your phone
line, and lets you make and receive calls.
Charger A cradle that charges an accessory handset. It connects to
power but not to a phone line.
Accessory
Handset
A handset that works with an expandable phone base.
Accessory handsets must be registered to a base.
Standby The handset is not in use. If it is off the cradle, no line has
been activated. No dial tone is present.
Station Any handset or the base.
Talk A telephone line has been activated on the handset or the
base, enabling a dial tone.
DECT6005 OM.indd 1DECT6005 OM.indd 1 20/8/07 1:49:19 PM20/8/07 1:49:19 PM

2
Compatible Bases
This handset is compatible with Uniden’s 1.8GHz DECT 6015
and DECT 6035 expandable phone series.
Installing the Accessory Handset
Checking the Package Contents
Make sure your package contains the following items. If any
items are missing or damaged, contact our Customer Service
Hotline. See inside the back cover page for contact information.
• Cordless Handset • Belt Clip
• Charger • Printed Material
• AC Adapter (model # AAD-600S: Input 240V AC, 50 Hz;
Output 9V DC, 210 mA)
• Rechargeable NiMH Battery Pack (model # BT-652: Capacity
650 mAh, 2.4V)
Installing the Battery
Follow the steps below to install the
rechargeable battery pack.
Using the finger indentation, press in on
the battery case cover and slide it down
to remove it.
Plug the battery connector into the
battery compartment jack. Be sure to
match the red and black wires to the
label near the jack.
Gently pull on the battery wires. If the
battery connector comes loose, try
connecting it again.
Replace the battery case cover and
slide it up until it clicks into place.
Note: Use only the Uniden BT-652
rechargeable battery pack supplied
with your cordless telephone.
1.
2.
3.
4.
DECT6005 OM.indd 2DECT6005 OM.indd 2 20/8/07 1:49:20 PM20/8/07 1:49:20 PM

3
Installing the Belt Clip
Line up the tabs with the holes on each side of
the handset. Press the belt clip down until both
tabs click into place.
To remove the belt clip, pull both sides of the clip
to release the tabs from the holes.
Installing the Optional Headset
Your phone may be used with an optional
headset. To use a headset, insert the headset
plug into the headset jack. Headsets may
be purchased by calling the Uniden Parts
Department. See inside the back cover page for
contact information.
Charging the Accessory Handset
The handset is powered by a rechargeable battery pack that
automatically recharges when the handset is placed in the
charger.
Connect the AC adapter to the DC IN 9V jack and to a 240V
AC outlet that is not controlled by a wall switch.
Caution: Use only the Uniden AAD-600S adapter.
Set the charger on a
desk or tabletop, and
place the handset in the
charger with the keypad
facing forward.
Make sure that the
charge LED illuminates.
If the LED does not
illuminate, check to see
that the AC adapter
is plugged in and
the handset makes
good contact with the
charging contacts on the charger.
Charge the handset battery pack for at least 15-20 hours
before using your new handset for the first time.
1.
2.
3.
4.
To AC outlet To DC IN 9V
AC adapter (supplied)
Route the cord.
Caution: Use only the Uniden AAD-600S adapter.
To AC outlet To DC IN 9V
AC adapter (supplied)
Route the cord.
Caution: Use only the Uniden AAD-600S adapter.
DECT6005 OM.indd 3DECT6005 OM.indd 3 20/8/07 1:49:20 PM20/8/07 1:49:20 PM

4
Registering the Handset
You must register the handset to the base before you can use it.
Only one handset can be registered at a time. (If an accessory
handset has ever been registered to a base, you must reset the
handset before you can register it to a new base.)
To register to a DECT 6000
series base, place the
accessory handset in the base.
While the handset is registering,
HANDSET REGISTERING
appears in the LCD. When
REGISTRATION COMPLETE is
displayed, the handset has been
registered to the base.
If REGISTRATION FAILED
appears, pick up the handset
from the base and try again.
Resetting the Handset
If you want to register the handset to a different base or replace
a handset with another one, you must first clear the registration
information from the base and the handset.
Press and hold []and [#] for at least five seconds, until the
SYSTEM RESET menu appears.
Select the DEREGISTER HS
submenu by pressing [Menu/Select].
WHICH HANDSET? appears in the
display.
Use []or [ ] to select the handset ID to be de-registered
from the list, and then press [Menu/Select]. DEREGISTER
HS appears.
Press [ ] to move the cursor to YES, and then press
[Menu/Select]. You will hear a confirmation tone.
1.
2.
3.
4.
Extra Handset
Extra Handset
Charger
Charger
Main Base
Extra Handset
+
Main Base
Charge the handset
for 15-20 hours.
Place the extra handset
in the main base to
register.
1
2
3
4
Registration
Complete.
Base #1
Extra Handset
Extra Handset
Charger
Charger
Main Base
Extra Handset
+
Main Base
Charge the handset
for 15-20 hours.
Place the extra handset
in the main base to
register.
1
2
3
4
Registration
Complete.
Base #1
Which Handset?
Handset #1
Handset #2
Which Handset?
Handset #1
Handset #2
DECT6005 OM.indd 4DECT6005 OM.indd 4 20/8/07 1:49:20 PM20/8/07 1:49:20 PM

5
Resetting the Handset Without the Base
If the original base this handset was registered to is not
available for some reason (for example, it is lost or somehow
incapacitated), you can still reset the handset and use it with
another base.
Press and hold []and [#] for more than five seconds, until
the SYSTEM RESET menu appears.
Press []to move the cursor to BASE UNAVAILABLE and
then press [Menu/Select]. WHICH BASE? appears.
Press []to move the cursor to the base which you want
to de-register from, and then press [Menu/Select]. BASE
UNAVAILABLE appears.
Press [ ] to move the cursor to YES, and then press
[Menu/Select]. You hear a confirmation tone, and the
handset deletes its own link to the base without trying to
contact the base.
Now you are ready to register the handset to the new base.
1.
2.
3.
4.
DECT6005 OM.indd 5DECT6005 OM.indd 5 20/8/07 1:49:21 PM20/8/07 1:49:21 PM

6
Using the Interface
Parts of the Handset
1
2
3
5
6
7
8
9
10
11
12
15
19
20
21
16
18
17
13
4
14
22
1
2
3
5
6
7
8
9
10
11
12
15
19
20
21
16
18
17
13
4
14
22
1. Headset jack cover
2. Belt clip hole
3. Speakerphone speaker
and ringer
4. Handset battery
compartment
5. new message LED
6. Handset earpiece
7. LCD display
8. [Clear/Int’com] key
9. [ ]key (up)
10. [ /Flash] key (talk/flash)
11. [ ]key (phonebook/left)
12. [
*
/tone] key
13. [Redial/Pause] key
14. [Menu/Select] key
15. [ /Mute] key (messages/
mute)
16. [ ]key (caller ID/right)
17. [ ]key (end call)
18. [ ]key (down)
19. [#] key
20. [ ]key (speaker)
21. Handset microphone
22. Handset charging contacts
DECT6005 OM.indd 6DECT6005 OM.indd 6 20/8/07 1:49:21 PM20/8/07 1:49:21 PM

7
Reading the Display
The handset display uses icons to tell you the status of your
phone. The table below lists the icons and what they mean.
Icon Status Description
Standby/
Talk
The battery icon indicates the handset
battery status: full, medium, low, and empty.
:OFF Standby The ringer off icon indicates that the ringer
is turned off.
Talk The mute icon appears while the handset
microphone is muted.
Talk The speaker icon appears when the handset
speaker phone is in use.
Talk The privacy icon appears when the Privacy
Mode is turned on.
Standby The voice mail icon appears when you have
messages waiting in your voice mailbox.
The Standby Screen
When the phone is in standby, the handset display shows the
following items:
:OFF
Handset #1
New CID: 5
battery icon
Ringer off icon
(when the ringer is off) Handset ID
Number of new Caller ID calls received
Using the Four-way Function Key
Your handset has a four-way
function key that allows you
to move the cursor or pointer
on the display and access the
most commonly used features
at the touch of a button.
Press the left side of the
key to open the phonebook.
Press the right side to open
the Caller ID list.
To use this four-way key, place your thumb over the key on the
handset and move to the four positions to get the feel of how it
moves and operates.
View the
phonebook
Four-way
Function Key
Up
View the
Caller ID
Down
View the
phonebook
Four-way
Function Key
Up
View the
Caller ID
Down
DECT6005 OM.indd 7DECT6005 OM.indd 7 20/8/07 1:49:21 PM20/8/07 1:49:21 PM

8
Using the Handset Menus
To open the menu, press [Menu/Select]. Highlight the option
you want by pressing the four-way function key. This will move
the cursor; the option currently highlighted has a triangle beside
it. Activate the highlighted option by pressing [Menu/Select].
To go back to the previous screen, press [left] on the four-way
function key. To exit the menu and return to standby, press [ ].
If you do not press a key within thirty seconds, the phone will
time out and exit the menu.
Entering Text from Your Handset
You can use the number keypad on your handset to enter text
by referring to the letters printed on each number key. When you
press the number key in a text entry field, the phone displays
the first letter printed on the number key. Press the number key
twice to display the second letter and three times to display the
third. Capital letters are displayed first, then lower case letters,
and then the number on the key.
If two letters in a row use the same number key, enter the first
letter, then use [right] on the four-way function key to move the
cursor to the next position to enter the second letter.
Number of times key is pressedNumber of times key is pressed
DECT6005 OM.indd 8DECT6005 OM.indd 8 20/8/07 1:49:22 PM20/8/07 1:49:22 PM

9
For example, to enter the word "Movies":
Press [6] once to enter M.
Use [right] on the four-way function key to move the cursor
to the right.
Press [6] six times to enter o.
Press [8] six times to enter v.
Press [4] six times to enter i.
Press [3] five times to enter e.
Press [7] eight times to enter s.
Press [Menu/Select] to end your text entry.
If you make a mistake while entering a name, use [right] or [left]
on the four-way function key to move the cursor to the incorrect
character. Press [Clear/Int’com] to erase the wrong character,
and then enter the correct character. To delete all characters,
press and hold [Clear/Int’com].
Note: When you enter the text, you can also use [#] to move the
cursor to right and [*/tone] to move the cursor to left.
1.
2.
3.
4.
5.
6.
7.
8.
DECT6005 OM.indd 9DECT6005 OM.indd 9 20/8/07 1:49:22 PM20/8/07 1:49:22 PM