Uniden XDECT 7005WP User manual

Not pictured:
Factory installed
-
rechargeable battery
Belt clip
-
AC adapter
(AAD-600S(M))
XDECT 7005WP waterproof accessory handset
and water resistant charger
Need Help? Get answers at our website: www.uniden.com.au for Australian
model or www.uniden.co.nz for New Zealand model.
Important Safety Precautions!
When using your telephone equipment, basic safety precautions should always be followed
to reduce the risk of re, electric shock and injury to persons, including the following:
The charger is NOT waterproof: Do not use or place the charger near water (e.g., near a bath

tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool).
If the charger falls into the water, unplug the AC adapter before removing it from the water.

After you remove the charger from the water, contact Customer Service (see our website for
contact information).
Wipe excess water o of the handset before returning it to the charger.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.

Use only the power cord and batteries indicated in this manual.

Do not dispose of batteries in a re. They may explode. Check with local codes for possible

special disposal instructions.
Do not place the handset in any charging cradle without the battery installed and the battery

cover securely in place.
SAVE THESE INSTRUCTIONS!
XDECT 7005WP Waterproof Accessory Handset
Owner's Manual
What's in the box?
XDECT_7005WP_OM.indd 1 28/9/11 12:17:54 PM

2
Understanding the Waterproof Handset
The handset complies with JIS7 water submersion specifications. It can remain

submerged under 1m of water for up to 30 minutes without damage or loss of
functionality.
If the handset falls into water, just remove it; you can continue using the handset

as normal.
The handset will still receive calls even if it is under water, but you probably won't

be able to hear the ringer or the earpiece. To avoid any accidents, do not try to
use the handset while it is still under water.
If you notice that the sound is distorted after your handset is submerged in water,

there might still be water around the speaker and microphone. Just shake the
handset to clear the water, and the sound should return to normal.
Don't place the handset where it will be subjected to direct sunlight for long

periods of time.
Installing Your Handset
Charge the Battery
The handset's rechargeable battery is already installed. Before you can charge the
battery, you have to power it on.
Remove the cardboard spacer.1)
Press the power on/off (activation) pin2)
according to the directions on the label.
Remove the label once the handset is powered on.3)
Save the power on/off pin in case you need to change the handset's power
status later (i.e., to power offw the handset when it will not be used for a
long time). Use the plastic power on/off pin or a blunt-tipped object like an
uncurled paper clip to press the power on/off toggle through the rubber seal.
Do not use a sharp object; sharp objects might puncture the rubber seal and
jeopardize the handset's waterproof status.
Connect the AC adapter to the charger's4)
DC IN 9V
jack and set the cord into the
notch. (This adapter might already be connected.)
Plug the other end of the adapter into a standard 240V AC power outlet.5)
XDECT_7005WP_OM.indd 2 28/9/11 12:17:54 PM

3
Place the handset in the charger with the display facing forward. The display on6)
the handset should turn on.
If... Try...
the handset display
does not turn on
Checking the AC adapter connection.
-
Seeing if the outlet is controlled by a wall switch.
-
Check handset activation at step 2 above.
-
Charge the handset completely (about 16 hours) before using it.
Registering to a Base
The accessory handset won't work until you register it to a base!
Compatible Bases
This handset is designed for use with Uniden's XDECT 7015 and XDECT 7055 bases.
Other compatible Uniden bases include the SSE25, SSE27, DECT 2015 and DECT2035
models. Some features may not be available when using the XDECT 7005WP with
these other bases. For the most up-to-date list of which bases this handset is
compatible with, see our website.
Registration Methods
If the other base has
an LCD display:
If the other base DOES NOT have
an LCD display:
On the base, open the menu.1)
Select2)
Register Handset . The
display should say Handset
Registering .
Disconnect the base AC adapter.1)
On the base, press and hold2)
FIND
while you reconnect the adapter.
On the handset, press and hold3)
HASH #
until the display says Handset
Registering (about 2 seconds).
After about 30 seconds, the handset display should say
Registration Complete .
XDECT_7005WP_OM.indd 3 28/9/11 12:17:55 PM

4
Test the connection
Pick up the handset and press
TALK/FLASH
. Make sure you get a dial tone.
(Press
END
to hang up.)
If... Try...
you don't hear a dial tone
-
the display says
-
Registration Failed
Making sure the handset is fully
charged, then trying again.
How to De-Register the Handset (for Registering to another base)
On the handset, press and hold1)
END
and
HASH#
until the System Reset menu
appears (about 5 seconds).
Select2)
Base Unavailable .
When the phone asks you to confirm, select3)
Yes . The handset deletes its own link
without contacting the base.
Using the Belt Clip
To attach the belt clip
Line up the holes on each side of the handset. Insert the belt clip into the holes on
each side of the handset. Press down until it clicks.
To remove the belt clip
Pull either side of the belt clip to release the tabs from the holes.
Important Information
Because the handset adapts to the base, the exact features and operation of the

handset will vary slightly depending on which base you register the handset to.
Refer to the user guide for the base you're registering the handset to for feature
descriptions.
All features and operation for the handset are described in the owner's manual

for one of the bases listed under the Compatible Bases section.
Owner's manuals for all Uniden phones are available on our website for free

downloading.
XDECT_7005WP_OM.indd 4 28/9/11 12:17:55 PM

5
Specications
AC Adapter Part number Input Voltage Output Voltage
AAD-600S(M) 240V AC, 50 Hz 9V DC@ 210mA
Battery pack Part number Capacity
BT-694s 500mAh, 2.4V DC
Use only the supplied AC adapter.

Be sure to use the proper adapter for the base and any chargers.

Do not place the power cord where it creates a trip hazard or where it could

become chafed and create a fire or electrical hazard.
Do not place the unit in direct sunlight or subject it to high temperatures.

Battery Information
Fully charged, the battery should provide about 8 hours of talk time and about 7

days of standby time. For best results, return the handset to the cradle after each
call to keep it fully charged.
Keep an eye on the battery status icon. When the battery gets too low, the

handset shows a low battery alert. If you hear a strange beep during a call, check
the display: if you see the low battery alert, finish your conversation as quickly as
possible and return the handset to the cradle. If the handset is in standby, none of
the keys will operate.
With normal use, the battery should last about one year. Replace the battery

when the talk time becomes short even when the battery is charged. To buy a
replacement battery, visit our website for contact information.
Replace the Rechargeable Handset Battery Pack
Follow these steps to replace the battery:
Unscrew the four screws holding the battery cover and remove it.1)
Remove the old battery pack from the battery compartment.2)
Line up the new battery's connector with the jack inside the battery3)
compartment (the connector only fits one way).
Push the connector in firmly. Tug on the battery wires gently to make sure you4)
have a good connection.
XDECT_7005WP_OM.indd 5 28/9/11 12:17:55 PM

6
Before replacing the battery cover, check the rubber seal located on the under5)
side of the cover: make sure that the seal is set in the groove and that there is no
foreign matter under the seal.
If the rubber seal appears warn, nicked, or dried out, you must replace it.
New seals are available through the Parts Department (see our website for
contact information).
Replace the battery cover; use the four screws to secure the cover to the back of6)
the handset.
Rechargeable Nickel-Metal-Hydride Battery Warning
CAUTION! Risk of explosion if battery is replaced by an incorrect type!
Dispose of used batteries according to the instructions. Do not open or
mutilate the battery. Disconnect the battery before shipping this product.
This equipment contains a rechargeable Nickel-Metal-Hydride (Ni-MH) battery.

Do not short-circuit the battery.

The rechargeable battery contained in this equipment may explode if disposed of in a re.

Do not charge the battery used in this equipment in any charger other than the one

designed to charge this battery as specied in the owner's manual. Using another charger
may damage the battery or cause it to explode.
Rechargeable batteries must be recycled or disposed of properly.
Uniden works to reduce lead content in PVC coated cords in our products and
accessories.
One-Year Limited Warranty
IMPORTANT Satisfactory evidence of the original purchase is required for warranty
service
Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below.
Warrantor
The warrantor is either Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”) or Uniden New Zealand
Limited (“Uniden NZ”) as the case may be.
Terms of Warranty
Uniden Aust/NZ warrants to the original retail purchaser only that the XDECT 7005 WP (“the Product”), will be free from
XDECT_7005WP_OM.indd 6 28/9/11 12:17:55 PM

7
defects in materials and craftsmanship for the duration of the warranty period, subject to the limitations and exclusions
set out below.
Warranty Period
This warranty to the original retail purchaser is only valid in the original country of purchase for a Product first purchased
either in Australia or New Zealand and will expire one (1) year from the date of the original retail sale.
If a warranty claim is made, this warranty will not apply if the Product is found by Uniden to be:
(A) Damaged or not maintained in a reasonable manner or as recommended in the relevant Uniden Owner’s Manual;
(B) Modified, altered or used as part of any conversion kits, subassemblies or any configurations not sold by Uniden
Aust or Uniden NZ;
(C) Improperly installed contrary to instructions contained in the relevant Owner’s Manual
(D) Repaired by someone other than an authorized Uniden Repair Agent in relation to a defect or malfunction
covered by this warranty; or
(E) Used in conjunction with any equipment, parts or a system not manufactured by Uniden.
Parts Covered
This warranty covers the Product and included accessories.
User-generated Data
This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation
phone numbers, addresses and images) that may be stored on your Product.
Statement of Remedy
If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either
repair the defect or replace the Product without any charge for parts or service. This warranty does not include any
reimbursement or payment of any consequential damages claimed to arise from a Product’s failure to comply with the
warranty.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
This warranty is in addition to and sits alongside your rights under either the COMPETITION AND CONSUMER ACT 2010
(Australia) or the CONSUMER GUARANTEES ACT (New Zealand) as the case may be, none of which can be excluded.
Procedure for Obtaining Warranty Service
Depending on the country in which the Product was first purchased, if you believe that your Product does not conform
with this warranty, you should deliver the Product, together with satisfactory evidence of your original purchase (such
as a legible copy of the sales docket) to Uniden at the addresses shown below. You should contact Uniden regarding
any compensation that may be payable for your expenses incurred in making a warranty claim. Prior to delivery, we
recommend that you make a backup copy of any phone numbers, images or other data stored on your Product, in case it
is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Service Division
345 Princes Highway,
Rockdale, NSW 2216
Phone number: 1300 366 895
Email address: [email protected]
UNIDEN NEW ZEALAND LTD
Service Division
150 Harris Road, East Tamaki
Auckland 2013
Phone number: [phone]
Email address: [email protected]
XDECT_7005WP_OM.indd 7 28/9/11 12:17:55 PM

© 2011 Uniden Australia Pty Limited. Uniden New Zealand Ltd.
Printed in Vietnam UUZZ01226BA(0)
For more exciting new products please visit our website:
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
XDECT_7005WP_OM.indd 8 28/9/11 12:17:55 PM