Uniden UH9000S User manual

UHF CB Transceiver
UH9000S / UH9060S / UH9080S
Fitting Instructions
Land Cruiser 70
Fitting Kit Part Number: UNIFK001

Page 2 of 12
Fitting Instructions
UH9000S / UH9060S / UH9080S
UHF CB Transceiver
Front
Antenna
Connector
Speaker
Microphone
UH9000S
Rear
Earth
A
ccessory
Power
+
Fuse
Power
Lead Patch
Harness
Antenna
Connector
Extension
Cable
(Optional)
UH9060S / UH9080S
Earth
A
ccessory
Power
+
Fuse
Remote LCD
Speaker
Microphone
Rear
UHF CB Transceiver
Front
Power
Lead Patch
Harness

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 3 of 12
WARNING
This vehicle is equipped with Supplemental Restraint System (SRS) airbags and seatbelt pretensioners.
Before starting work, wait at least 90 seconds after the ignition switch is turned off and the negative (-) battery terminal
cable is disconnected.
SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the ignition switch off
and disconnecting the negative (-) battery terminal cable, SRS parts may deploy possibly causing serious injuries.
WARNING
Do not install any parts in a location that may interfere with the operation and deployment of the SRS airbags or seatbelt
pretensioners, including driver, front passenger and knee SRS airbags if tted. Doing so may result in serious injury or
death.
PREPARATION
• Follow all standard workshop and occupational health and safety practices during the installation process.
• Check and note any existing marks or damage to the vehicle.
• Before starting the installation thoroughly read through these installation instructions then follow the tting sequence as described.
• Check that the UHF CB transceiver kit is complete.
• Take all possible precautions to avoid damaging the vehicle’s interior and exterior during the installation. Use protective tape on
parts and tools where necessary.
• To avoid damage to the wiring harness and antenna cable, avoid contact with sharp edges. Cable tie securely every 200 mm.
• Ensure all removed parts are re-tted correctly.
SPECIAL TOOLS
• Trim removal tools
• Protective tape
• Lead wire
PARTS LIST - UHF CB TRANSCEIVER KITS
Model UHF CB Transceiver Kit Fitting Kit Part Number
LAND CRUISER 70
UH9000S
UNIFK001UH9060S
UH9080S
PARTS LIST - ANTENNA
Model Antenna Part Number Description
LAND CRUISER 70
AT970BKTWIN Antenna Dual Whip Black
AT970WTWIN Antenna Dual Whip White
AT970BK Antenna 1200mm Black
AT970W Antenna 1200mm White
AT890BK Antenna 1000mm Black
AT890W Antenna 1000mm White
AT880TWIN Antenna Dual Whip Stainless Steel

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 4 of 12
REMOVAL
Removal - Engine Bay
1. Open the bonnet.
2. Disconnect the (-) negative battery terminal cable.
3. Disconnect the positive (+) terminal cable.
4. Remove the battery retaining bracket and hook.
5. Remove the battery and store safely.
6. Cut the outer tang off the rewall grommet where
indicated.
Removal - Interior
1. Fold back the passenger’s side footwell carpet.
2. Remove the (2) screws securing the cup holder.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 5 of 12
3. Remove the scrivet securing the cup holder.
4. Lift the cup holder away from the transmission tunnel.
Remove the (2) outer screws securing the upper and lower
sections.
5. Turn the cup holder over and remove the (1) retaining
screw underneath the cup holder.
6. Unclip the upper and lower sections to expose the power
socket connector.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 6 of 12
INSTALLATION
Antenna
1. Remove the sleeve, spacer washer, lock washer and nut
from the antenna.
2. Pass the antenna cable through the antenna mounting
hole.
3. Secure the antenna to the mount using the sleeve, spacer
washer, lock washer and nut. Tighten securely.
Antenna Cable
1. Pass the antenna cable through the radiator grille opening
in the location as shown.
2. Route the antenna cable through the radiator support
panel, under the A/C tubes into the engine bay as shown.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 7 of 12
3. From the radiator support panel, route the antenna cable
under the front of the battery tray, below the washer bottle
and along the inner quarter panel behind the earth strap
and existing wiring harness.
4. At the completion of the installation, cable tie the antenna
harness to the existing wiring harness where indicated [ ].
5. Continue routing the antenna cable along the inner
quarter panel towards the rewall following the existing
wiring harness. Route behind the fuel lter and below the
accessory fuse box and associated wiring.
6. At the completion of the installation, cable tie the antenna
cable to the existing wiring harness where indicated [ ].
7. Route the antenna cable from beneath the accessory fuse
box to the rewall grommet as shown.
8. At the completion of the installation, cable tie the antenna
cable to the existing wiring harness where indicated [ ].
9. Pass a lead wire through the cut rewall grommet opening
to the passenger’s side footwell.
Attach the antenna cable to the lead wire.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 8 of 12
10. Carefully pull the lead wire and antenna cable through
from the passenger’s side footwell.
IMPORTANT
Use silicon spray to allow the antenna cable to pass
through the grommet more easily.
At the completion of the installation process seal the
antenna cable grommet entry point with an automotive
grade sealant and secure with insulation tape.
11. Disconnect the lead wire and route the antenna cable
below the carpet line through the centre of the instrument
panel.
Power Lead Patch Harness
1. Disconnect the power socket connector and dehouse the
(2) connector pins from the rear power socket connector
[1].
2. House the (2) removed pins in the power lead free patch
harness connector [2].
3. House the (2) free power lead patch harness pins into the
existing power socket connector [3].
4. Connect the existing power socket connector to the power
socket [4].
IMPORTANT
5. Refer to the following diagram for wiring details..
LC70
1
Power
socket
Existing vehicle
harness
Existing vehicle power
socket connector
Existing vehicle power
socket connector Power
socket
4
To UHF CB
transceiver
Power lead
patch harnesss
Existing vehicle power
socket connector
To UHF CB
transceiver
3
Existing vehicle
harness Power lead
patch harness
2
Existing vehicle
harness Power lead
patch harness To UHF CB
transceiver
1
2
1
2
1
2

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 9 of 12
6. Re-assemble the two halves of the cup holder using the
original fasteners. Ensure the power socket harness and
the UHF CB transceiver power harness are correctly
positioned through the cut-out.
7. Position the UHF CB transceiver power harness and fuse/s
neatly below the centre of the instrument panel.
Cable tie [ ] using self-adhesive cable tie mounting blocks
where necessary to avoid fouling and rattling.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 10 of 12
UHF CB Transceiver Cradle and Radio
1. Using a suitable primer clean the instrument panel at the
cradle mounting location
2. Fit the UHF CB transceiver cradle to the centre of the
instrument panel in the location shown using double sided
tap provided. Trim double sided tape to suit.
WARNING
If the indicated location is not suitable, do not install the
UHF CB transceiver cradle and radio in a location that may
interfere with the operation and deployment of the SRS
airbags or seatbelt pretensioners, including driver, front
passenger and knee SRS airbags if tted. Doing so may
result in serious injury or death.
3. Assemble the (2) slide mount brackets to the UHF CB
transceiver using the (2) screws supplied.