UniPOS VIT 01 User manual

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 1
Revision 10/02.17 Pages51
WIRELESS FIRE ALARM CONTROL PANEL
VIT01
INSTRUCTION MANUAL
Revision 10/02.17

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 2
Revision 10/02.17 Pages51
Contents
1.
2.
3.
4.
4.1.
4.2.
4.3.
4.4.
5.
5.1.
5.2.
5.3.
6.
6.1.
6.2.
6.3.
7.
7.1
7.2.
7.3.
8.
8.1.
8.2.
8.3.
9.
9.1.
9.2.
9.3.
10.
10.1.
10.2.
10.3.
11.
11.1.
11.2.
11.3.
11.4.
11.4.1.
11.4.2.
11.4.3.
11.4.4.
12.
12.1.
12.2.
12.3.
12.4.
12.4.1.
12.4.2.
12.4.3.
12.4.4.
13.
14.
15.
16.
17.
Terminology................................................................................................................
Technical data............................................................................................................
Contents of delivery....................................................................................................
Installation and setup for operation...........................................................................
Defining of the structure of the radio network.............................................................
Installation of the Control Panel..................................................................................
Description of inputs and outputs. Mounting peripheral devices.................................
Connection power supply...........................................................................................
General information…………………………………………………………………………
Access levels..............................................................................................................
Means of control and indication..................................................................................
Display and using the buttons.....................................................................................
“Duty Mode”................................................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
“Fire condition”...........................................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
“Fault condition”.........................................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
„Disabled component” ...............................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
“Тest Mode”................................................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
”Information and control”.............................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
Using the Menus.........................................................................................................
Status..........................................................................................................................
Archives......................................................................................................................
Disabled devices.........................................................................................................
Set Up.........................................................................................................................
Set Up condition..........................................................................................................
Description..................................................................................................................
Indication.....................................................................................................................
Using the keypad........................................................................................................
Using the Menus.........................................................................................................
Menu Control Panel....................................................................................................
Menu Zones Set Up....................................................................................................
Menu Registration.......................................................................................................
Default parameters………………………………………………………………………….
Labour protection requirements..................................................................................
Fire Control Panel initial Start Up................................................................................
Conditions of operation, storage and transportation...................................................
Warranty obligations...................................................................................................
Recommendations before final installing of wireless fire alarm system on site……...
4
5
6
6
6
8
8
11
11
11
12
13
14
14
14
14
15
15
15
16
17
17
17
18
18
18
19
19
19
19
19
20
20
20
20
20
21
21
23
24
24
24
24
24
25
25
26
29
32
41
42
42
42
42
43

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 3
Revision 10/02.17 Pages51
17.1.
17.2.
17.3.
17.4.
17.5.
18.
Checking for other devices working on the same band………………………………...
Preliminary radio test……………………………………………………………………….
Routers and “parents”………………………………………………………………………
Several steps in building configuration……………………………………………………
Possible reasons of dropping messages between elements in the system………….
Appendixes.................................................................................................................
43
43
43
44
46
47

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 4
Revision 10/02.17 Pages51
Introduction
Wireless Fire Alarm Control Panel VIT 01 is designed for fire security, management and control of
wireless fire alarm devices. The usage of radio communication between the control panel and the fire
detectors makes it suitable for installation into premises, where laying cables is unwanted. The
Control Panel is designed and produced by the requirements of ЕN 54-2/4 and EN 54-25.
The Control Panel operates together with:
-automatic fire detectors VIT20, VIT30, VIT60;
- manual call point VIT50;
-router (controller) VIT02.
Basic functional characteristics:
setting up of the operating modes and parameters of fire detectors, routers and outputs
through a built-in keyboard;
control for removed(tampered) fire detector from its base, battery status;
control over the level of radio signal of the devices;
option for changing parameters of the fire detectors;
LCD display for visualization of the operating modes of the system;
LED indication for signalization of emergency and extreme situations in the zones and within
the whole system;
non-volatile archive memory, saving up to 4096 events, indicating the time and the type of the
event, and allowing a perfect analysis of the actions of authorized personnel and the possible
problems in the process of fire safety of the premise;
user friendly test modes for all the system components, providing a total control over the
condition of the protected premise;
test and choice of 16 different channels to establish radio connection;
automatic restoration in fault condition, after the reason, that caused the fault has been
removed;
built-in serial interface RS232/RS485 for connection with personal computer;
different ways possibility of installation designs, within the range of the control panel’s
resources.
1. Terminology
Addressable point –Detector or manual call point that can be indentified individually by the
Control Panel;
Fire detector (FD) –a device that monitors the status of one or more input signals and sends a
message for fire condition upon certain state of the signal;
Router (Controller) - a device which serves to retransmit the signals between the control panel
and fire detectors. Each router has one monitored output to signal a fire condition. It can be enabled
or disabled in case of faulty.
Network ID (PAN) –Identification number of the radio network of the Control Panel. Each
network has an unique identification number.
Link quality indication –parameter, indicating the radio signal level between fire detector and
conotrol panel. The quality of the connection is measured in the range of 0 to 99 %.
Output –monitored or relay output. Can be programmed by the user to be activate in case of fire
event.
Disabled component –fire detector, which is not monitored for fault and fire condition or an
output which is not controlled or monitored in case of fire or fault condition. This condition can be set
by the user. Indication of a disabled device includes a common light signalisation and text information
on the LCD.
Monitored output –a potential output, which allows for monitoring the condition of the connected
wires between the control panel and the executive device. It requires using a special wiring diagram.
Local sounder –built-in into the control panel, activated upon fire condition or fault condition;
Access level –access level to various indications and control functions.
Fire condition Stage 1 (Fire 1) –fire mode, entered by the control panel upon activation of an
automatic fire detector. It will continue until the control panel is reset by manual operation. This fire

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 5
Revision 10/02.17 Pages51
mode is indicated by common light signalization, local sound signalization and text information on the
LCD display.
Fire condition Stage 2 (Fire 2) –fire mode, entered by the control panel in two situations:
after time Fire 1 –Fire 2 expires;
activation of a manual call point VIT50;
The phase is indicated by a common light signalization, a local sound signalization and text
information on the LCD display.
Relay output –relay, potential-free, switching outputs that controls external executive devices.
2. Technical data
2.1. Maximum number of addressable devices / zones per system
- 32/15
2.2. Radio network parameters
Frequency - 2.4 GHz
Maximum number of routers connected to one control panel - 6
Maximum number of routers connected in series to one control panel - 4
Maximum number of adressable devices (FDs and routers) connected directly to the
Control Panel - 20
Maximum number of fire detectors connected to router - 14
2.3. Controllable outputs - 2 pcs.
Type - potential, relay
Electrical features - (24±5)V DC/1 A
2.4. Relay output for fire condition - 1 pc.
Type - potential-free, switching
Electrical features - 3A/125VAC; 3A/30VDC
2.5. Relay output for fault condition - 1 pc.
Type - potential-free, switching
Electrical features - 3A/125VAC; 3A/30VDC
2.6. Indication of the registered events
Light indication - LED
Text messages - crystal-liquid display –
4 rows, 20 characters per row,
cyrillic, back-lit
Sound - built-in sounder
2.7. Power supply
2.7.1. Mains power supply - 220/230 VAC/50 Hz
2.7.2. Back up (battery) power supply:
battery type - lead, gel electrolyte
number of the batteries - 2 pcs
connection - serial connection
nominal voltage of the connected back up batteries - 24 VDC
nominal capacity С20 - (1,2 –4,5) Ah
terminal discharge voltage - 17,6V
charge voltage - 28V
consumption on the back up battery supply - <180mA at 24V
2.7.3. Fuses
mains supply 220/230 V - 4,0 А
1. back up battery supply - 2,0 А
2.8. Overall dimesions - 313х218х85 mm
2.9. Weight (excluding the back up batteries) - 1,440 kg

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 6
Revision 10/02.17 Pages51
3. Contents of delivery
Fire Control Panel VIT 01 - 1 pc.
Resistors 5,6k/ 0,25W - 2 pcs.
Cable Bridge for the back up batteries - 1 pc.
Fuse 4A - 1 pc.
Fuse 2A - 1 pc.
Instruction Manual and Instructions
for the authorised staff on a CD - 1 pc.
Antenna - 1 pc.
Transport package - 1 pc.
4. Installation and set up for operation
4.1. Defining of the structure of the radio network
It is necessary before installation to define the structure of the radio network. On fig. 1.1, 1.2 and
1.3 are shown different types of connection.
In the first case (fig 1.1), 5 routers (controllers) are
connected in series. Fire detectors are additionally
connected to 4 of them and to the Control Panel. Fire
detectors can not be connected to router (R) 5, due to
the limitation –messages between the elements within
the system can be retransmitted not more than 5 times.
V I T 01
V I T 02
No. 5
V I T 02
No. 4
V I T 02
No. 3
V I T 02
No. 2
V I T 02
No. 1
Fig.1.1

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 7
Revision 10/02.17 Pages51
In the second
case (Fig.1.2), 6
routers (controllers)
are connected
directly to the
Control Panel and to
each of them
(including to the
control panel) are
joined fire detectors.
In this case, the
maximum number of
retransmissions of
messages is 2.
VIT01
VIT02
No.1 VIT02 No.2 VIT02
No.3 VIT02
No.4 VIT02 No.5 VIT02 No.6
Fig.1.2
In the last case the connection is
mixed. Part of fire detectors and the
routers are connected directly to the
control panel, some of them - to other
routers in a hierarchical structure.
In cases when the system device
range has not reached full capacity, the
method for configuration is not
essential. Configuration must be build
on way that signal strenght is best
between elemenents of the network
(see 17.2.). Each device in its initial
connection is scanning for a Router or
for a Control Panel with the best quality
connection. Ones detectors find its
Control Panel or Router,
communication in the future work of the
detector will be implemented through a
remembered element (Panel or Router)
until further actions will be performed.
When in the system should be
connected maximum number of
devices, or close to the maximum
devices capacity and the limitation of
the connected devices is up to 14 to
some panel or R, then the sequence of
the initial connection is very important.
The method is the following - at any
moment there should be only one
element which is enabled (a router and
a Control Panel) for connection.
VIT 01
VIT02
No.1 VIT02 No.2 VIT02
No.3
VIT02
No.4 VIT02 No.5 VIT02
No.6
Fig. 1.3
As an example, consider the establishing of the system in Figure 1.1. In the following order:
Connect router1;
Disable the connection of other devices,directly to the Control Panel;
Connect router2. At this point, it can be connected only through router1, as the only one
device, open for new elements;
Disable connection of devices to router1;

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 8
Revision 10/02.17 Pages51
Connect router3 to router2;
In the described method above, connect R4 to R3, R5 to R4. In this configuration of the
network it is not possible to connect any devices to R5, because limitation of the
retransmissions of the messages through routers is 5 (see 2.2.) ;
Join fire detectors to router4;
Disable the connection to router4 and enable connection to router3;
Join the fire detectors of router3;
Perform the same procedure with the fire detectors for connection to R3, R2, R1 and the
Control Panel.
4.2. Installation of the Control Panel
unpack the Control Panel;
mount the dowels for fixing the Control Panel onto a specific place;
fix the Control Panel to the dowels through the three openings of the box (pos.3, fig.2).
Fig.2
4.3. Description of inputs and outputs. Mounting peripheral devices to the Control Panel
All accessions are made by means of terminals, mounted on the printed circuit board (pos.4,
fig.2). Please note that the consumption of the controllable output should not exceed, 1,0 А in any fire
panel mode.
“+Out1-”, “+Out2-”–Monitored outputs- relay, potential, the line is monitored for short-
curcuit and for interruption. Outputs are used to manage devices in fire mode of the Control
Panel. These outputs are programmable outputs.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page 9
Revision 10/02.17 Pages51
“GND” –GND terminal.
“+28V-”–Terminal for user supply voltage 28V to peripheral devices.
“Rel Fire” –Output, relay, potentiial-free, the line’s status is not monitored.The output is
used to control devices in fire mode of the Control Panel.
“Rel Fault” –Output, relay, potential-free, the line’s status is not monitored. The output is
used to control devices in fault condition of the Control Panel.
“+28V” –Two terminals for supply voltage +28V to peripheral devices.
“RS232/485” –Terminals for connection of two-wire line of interface RS485 or three-wire
line for RS232. Switching between interfaces is done by changing position of a jumper on
the board. Interface RS232 is used for a connection with a РС. RS485 is intended for a
connection between different Control Panels VIT01 (this functionality is not available in the
current version of the Control Panel). There is a jumper provided, which terminates the line
with resistor 120 upon mounting. This is necessary if the Control Panel is the endpoint of
the interface line. The interface requires both ends of the line to be terminated with
resistors 120.
“┴” –Terminal for connection of a third wire / shield / on the interface cable.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page10
Revision 10/02.17 Pages51
Fig.3
4.3.1. Description and mounting of devices to output “Rel Fire”
Output “Rel Fire” is a relay output with potential-free contacts, situated on the terminal bus:
–normally open “NO”;
–normally closed ”NC”;
–common point “С”.
In Duty Mode there is a contact between terminals “C” and “NС” of the relay.
In Fire condition, there is a contact between terminals “C” and “NO” of the relay.
The output is not monitored for short-curcuit or interruption.
The relay contacts do not commutate 220V!
4.3.2. Description and mounting of devices to output “Rel Fault”
Output “REL Fault” is a relay output with potential-free contacts, situated on the bus terminal:
–normally open “NO”;
–normally closed ”NC”;
–common point “C”.
The output is activated in Fault condition.
In Duty Mode there is a contact between terminals “C” and “NO” of the relay.
In Fault condition, there is a contact between terminals “C” and “NC” of the relay i.e. an output
device, commutated through the contacts of “REL Fault” will signal for fault condition in the system.
The output is not monitored for short-curcuit or interruption.
The relay contacts do not commutate 220V!
4.3.3. Monitored outputs “Out1” and “Out2”
Outputs are connecten on two-wire line for connection with the devices for sound and light
signalization.
The line is trimmed and monitored for interruption and for short-circuit.
In order to control the condition, it is necessary on the terminals of the signaling device to place
resistor 5.6 к/ 0.25W.
- Out x +
5,6 k
On activation the monitored outputs supply voltage (24±5) V. Maximum current load of the output
is 1А.
Outputs are programmable and can be activated in Fire mode.
In case of short circuit between “+” and “-“ the output activation will be disabled.
4.3.4. Description and installation of devices to terminals of interface RS232/RS485
Interface RS232/485 is used for connection between the Control Panel and other intelligent
devices and PCs.
The connection between devices on RS485 is done by parallel connecting on two-wire line observing
the requirement, potential "A" and "B” should not be crossed. The maximum distance between the
final devices is 1000 m. Regardless of the length of the line, on the first and on the last device, it is
necessary to put the jumper for line termination with 120. For all other devices, the jumper must be
removed.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page11
Revision 10/02.17 Pages51
For connection of the Control Panel with the devices on RS232 we use three-wire line –RX, TX
and GND. The signal lines RX and TX connecting the panel and the other device should be crossed.
The so-called "NULL modem" cable is suitable for this conneciton. The maximum distance between
the Control Panel and the other device is 15 meters. In this case, communication is “point to point”.
4.4. Connecting power supply
Connect power cable to the terminal (pos.1, fig.2) with fuse (pos.2, fig.2), observing the following
location: -L –feeding wire “Phase”;
-N –feeding wire “Null”;
-“Ground”–safety ground wire.
The cable must be double insulated, with cross section not less than 0,5 mm2for the feeding
wires, and 1,5 mm2for the safety ground wire.
Connect the other end of the feeding cable to the mains, using a junction box.
Mains power supply of the Control Panel should be on a separate circuit.
5. General information
5.1. Access levels
There are four access levels in the Control Panel:
5.1.1. Access level 1
These are the access levels for all persons who are intended to find out and react initially on the
signalizations for fire condition or/and fault condition.
The personnel with Access level 1 shall be trained and authorized to operate with the Control Panel in
conditions Duty Mode, Fault condition, and Disabled component.
In access level 1 the following features are available:
-displaying suppressed messages for fire condition,fault condition or disabled
component;
-start inspection time period;
-suppressing the local sounder.
All light indications of the Control Panel are visible.
5.1.2. Access level 2 –Default password - 0000
Two actions lead the operator to Access level 2:
-unlock and open the front cover of the Control Panel (part of the actions);
-enter password for access level 2 or 3.
In access level 2 the following features are available:
-all accessable features of Access level 1;
-reconfiguration specific data of the Control Panel;
-replacing a burnt fuse;
-connecting of output devices;
-suppressing and re-activation of the fire alarm outputs;
-setting up and excluding a zone in „Test”;
-activating all the outputs within the system („Evacuation”);
-testing or disabling the system outputs;
-LED test of all LEDs on the panel;
-Setting date and time;
-Changing language of the panel’s menus;
-resetting fire condition.
5.1.3. Access level 3 –Default password 1111
Two actions lead the operator to Access level 3:
-unlock and open the front cover of the Control Panel (part of the actions);

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page12
Revision 10/02.17 Pages51
-enter password for Access level 3.
The following features are accessible:
-all accessable features of Access level 2;
-entering and changing password for Access level 2 and level 3;
-deleting the archive;
-registration, exchange and exclusion of addressable points in the radio
network;
-changing the parameters of the addressable points and zones.
5.1.4. Access level 4
Accessible for personnel, trained and authorized by the producer to dismantle the fire control
panel and to modify the software. Special means are required for access this level.
5.2. Means of control and indication
Wireless Fire Control Panel VIT01 operates in seven basic conditions: Duty Mode, Fire
condition mode, Fault condition mode, Disabled component mode, Test mode, Information and
control mode and Set Up mode.
At any moment, the control panel can be in one of them or in random combination of modes: Fire
condition, Fault condition, Disabled component, Test and Information and control.
The condition Set Up can not be combined with another condition.
Entering Set Up condition exits all the other conditions.
The Control Panel conditions and their corresponding indications are described in Table 1. Table 1
Condition of the Fire Control Panel
Indication
All conditions -
The fire control panel is power supplied
Indicator Power supply –
continuous green light
Fire condition Phase 1 –inspection time is entered
Indicator „Time Delay” –
continuous yellow light (if time
delay is set)
Duty Mode, Fault condition, Information and control-
disabled components are available
Indicator „Disabled component” –
in case of disabled component
Duty Mode, Fault condition, Disabled component,
Information and control –Test Mode
Indicator Test
Fire condition
Common indicator “Fire condition”
- red light in combination with the
individual indicator of the zone,
where the fire condition has been
registered.
Fault condition -
All fault conditions, excluding low power
Common indicator “Fault
condition” - continuous yellow light
Fault condition –System fault
Indicator “System fault” -
continuous yellow light
Fault condition
Indicator “Fault in Power supply” -
continuous yellow light
Fault condition
Indicator “Fault in a monitored
output” - continuous yellow light
Fire condition
Local sounder- discontinuous signal –fast
beeping

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page13
Revision 10/02.17 Pages51
Condition of the Fire Control Panel
Indication
Fault condition
Local sounder - discontinuous signal –slow
beeping
Table 2
Means of control
Condition of the
Control Panel
Access
Lecel
Operation
Button “Reset”
Fire condition
Levels 2
and 3
Reset Fire condition Stage 1 or Fire
condition Stage 2, indicated on the display
Button “Outputs”
Fire condition
Levels 2
and 3
- In presence of activated outputs for Fire
condition –suppresses the outputs;
- In suppressed outputs for Fire condition –
reactivates the outputs
Duty Mode
Forced outputs activation –Evacuation (see
6.3 - Note)
Button “Alarm”
Fire condition or Fault
condition
All
Suppressing/ activating of the local sounder
Button “Menu”
Duty Mode, Fire
condition, Fault
condition, Test and
Disabled component
All
- Enter next menu;
- Confirm data;
- Next position.
Button „Down”
Set Up, Fire
condition, Fault
condition, Test and
Disabled component
Levels 2
and 3
- Selects next basic screen;
- Moves the cursor through menus;
- Selects next parameter.
Button “Up”
Set Up, Fire
condition, Fault
condition, Test and
Disabled component
Levels 2
and 3
- Selects the next screen;
- Moves the cursor through menus;
- Selects next parameter.
Button „End”
Set Up, Fire
condition, Fault
condition, Test and
Disabled component
Levels 2
and 3
Returns to the previous screen
Button „Inspection”
Fire condition
All
Adds additionally set inspection time for
each activated zone between phase 1 and
2.
5.3. Display and using the buttons
5.3.1. Display
The LCD display shows three types of information:
basic screens;
menus;
entering parameters.
The basic screens display information about the system status or the condition of one of its
components, as well as event log information about past events in the system.
The menus display different options for selecting function or submenu.
The cursor is a flashing rectangle and it moves along the row of buttons and .

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page14
Revision 10/02.17 Pages51
On the screens for entering parameters are given the parameter name and to what part of the
system is related. The cursor is a line below the changing value.
5.3.2. Using the buttons
For operating the Control Panel are used 8 buttons, as 4 of them are with unique functions in
mode „Fire condition”, and the rest are used in the context of the displayed information, namely:
Menu/ Confirmation :
oIn the main screen –selects menu for possible functions;
oIn the screen with menu –confirms the function, selected by the cursor.
oIn the screen for changing the parameter –confirms the entered value and
selects the next in the line. For some parameters as names and passwords, the
button moves the cursor on the next digit or character. Holding the button for
more than 1 second completes the operation on entering parameters and
proceeds to the next submenu.
Vertical arrows and :
oIn the main screen –select next main screen;
oIn the screen with menu –move the cursor up and over the elements of the
menu;
oIn the screen for changing the parameter –increase and decrease the current
value of the selected parameter. Holding the button for more than 1 second
changes the values with high speed.
Exit :
oIn the screen of submenu and screen with menu –returns the dispay to the
previous main screen;
oIn the screen for changing the parameter –records the changes of the
parameters (if changes were made) and returns the display to the previous
main screen;
Diagram of the screens and menus of the Control Panel is shown in Appendix 2.
6. Duty Mode
6.1. Description
The Fire Control Panel is in Duty Mode, when it is not in any other modes.
6.2. Indication
6.2.1. LED and sound indication
In this conditionis is illuminated only the green LED indicator (“Power Supply”). The yellow
LED indicator („Disabled component”) – is illuminated only if there are disabled components.
The indicator „Test”is illuminated if there is a zone set in test.
Local sounder is swiched off.
6.2.2. Text indication
The display shows the following
information:
- Condition of the Control Panel (Duty);
- Real time;
- Weekday;
- Current date;

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page15
Revision 10/02.17 Pages51
6.3. Using the keypad
The only one active button at that condition is (“Menu”). The button is accessable for all the
Access Levels. Information about the status of devices, outputs, zones and Control Panel is available
at all access levels.
Note: In „Duty Mode”the outputs of the Control Panel and the connected to it routers can be
forced to activate by pressing button at access level 2 or higher. In this case the display shows
the text „Evacuation”.
7. Fire condition
7.1. Description
The Fire Control Panel enters Fire condition mode upon activation of a fire detector of the system.
Exit from this mode is only through manual operation –pressing button with access level 2
or 3 password.
7.2. Indication
7.2.1. LED and sound indication
In this condition are illuminated:
-With green light indicator (“Power supply”);
-With red light indicator (“Fire condition”);
-With red light the indicator of the relevant zone ;
-If the outputs for fire condition are suppressed by button (“Outputs”), the LED
indicator of the button is illuminated in continuous red light;
-If the sound indication is suppressed by button (“Alarm”), the LED indicator of the
button is illuminated in continuous red light.
The local sounder produces a discontinuos signal –fast beeping.
7.2.2. Text indication
In this condition the display is divided into
two text fields:
On the first and on the second line it is
displayed information about:
-Number of fire;
-The fire detector in fire condition
(if it is only one);
-The first fire detector, reported a
signal for fire condition (if there
are more than one signals for
fire)
On the 3rd and 4th line:
-it is duplicated information about the fire detector in fire condition (of only one);
-it is displayed information about the last activated fire (if more than one) and its
number.
The following information is visuslized on the display:
On the first line:
- Number of fire (Example: 01);
- The Phase of the Fire condition (Example: Fire1);
- Address and user description name of the fire detector (Example: 17 Room
15);
On the second line:

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page16
Revision 10/02.17 Pages51
- Number and user description name of the zone (Example: 01 Floor1) to which
detector belongs;
- At phase 1 –the time in seconds, remaining to entering phase 2 (Example:
33).
On the 3rd and 4th line –corresponding information about the last activated fire (if they are more
than one) or duplicated information from the two lines above (if the activated fire detector is only
one).
The Control Panel enters „Fire condition 2” after the set time between phase 1 and phase 2
expires. Default time between phase 1 and phase 2 is 60 seconds and can be change from
parameters of the zone.
Proceeding to „Fire condition 2” is performed immediately in the following cases:
the set time Phase1-Phase2 and the inspection time are 0.
the fire condition signal comes from FD type VIT50 and parameter „Manual Call point priority”
of the zone is set to „Yes”.
button is held down more than 5 seconds.
7.3. Using the keypad
Actions on using with buttons apply to all the areas, where the fire condition occurs.
Button
Access
Level
Action
Additional information
Button (“Alarm”)
All
Pressing the button :
- switched off the local
sounder ;
- activates the local sounder,
if the Control Panel has
entered Fire condition or
Fault condition, and the local
sounder was muted by
previous pressing of the
same button.
The action of the button is
reversible i.e by single pressing
changes the current condition
respectively –switched off or
switched on sounder.
LED indicator is illuminated if
the condition switched off
sounder is active.
The local sounder is
activated again:
- upon entering Fire
condition of the Control
Panel from a new zone;
- in occurance of a new
fault or fire.
Button
(“Outputs”)
2nd or
higher
Pressing the button:
suppresses the outputs,
switched off , in case of Fire
condition;
activates the suppressed
outputs if there are any;
in case the Control Panel is
in Fire 1, it goes to to Fire 2
if the button was held down
for more than 5 seconds.
Operating with the button
requires access level 2 or higher.
The action of the button is
reversible i.e by single pressing
changes the current condition
respectively –suppressed or
activated outputs.
LED indicator is illuminated if
the condition suppressed outputs
is active.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page17
Revision 10/02.17 Pages51
Button
(„Inspection”)
All
Adds Inspection time in the Control
Panel is in „Fire 1”.
Time is set for each zone.
If this button is pressed when
the Control Panel is in „Fire 1”,
that increases the time period
between phase 1 and phase 2 of
the occurred fire condition with
set inspection time until the
Control Panel enters „Fire 2”.
Button (“Reset”)
2nd or
higher
Pressing the button forces the
control panel to exit from Fire
condition –clears all fires in all
zones
Operating with the button
requires access level 2 or higher.
Button (“Menu”)
All
Pressing the button enters
condition Information and control.
Check the condition of the
fire detectors and the current fault
conditions.
Buttons („Up”
and „Down”)
и
All
If the fire conditions are more
than one, information about each of
them is displayed by means of the
buttons.
Button (“Exit”)
All
Pressing the button leads to exit
from the condition Information and
control. The main screen in the
current Fire condition is visualized.
8. Fault condition
8.1. Description
The Fire Control Panel enters „Fault Condition”upon detecting fault in one of the modules or/and
in one of the devices, registered within the system;
A list of possible faults is given in Appendix 2.
8.2. Indication
8.2.1. LED and sound indication
For all fault conditions, indicator (“Fault”) is on with continuous yellow light. Depending on
the type of the fault condition, the following indicators are also illuminated:
In system fault - indicator (“System fault”) with continuous yellow light;
fault in a controllable output - indicator (“Fault short-circuit or an interrupted controllable
output”) with flashing yellow light;
in fault of the mains or back up batteries supply - indicator (“Fault Power supply”)is
illuminated with continuous yellow light;
in fault in any of the fire detectors, the indicator of the zone, to which it belongs
is illuminated in flashing yellow light.
The local sounder is activated and produces discontinuous signal. In case the sound signalization is
suppressed by button (“Alarm”), the LED indicator of the button is illuminated in continuous red
light.
8.2.2.Text indication
The screens of fatal faults suppress all other messages. In the occurance of more then one non-
fatal faults, they are indicated by their time of appearing. Last fault is indicated on the display.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page18
Revision 10/02.17 Pages51
Upon registering of fault condition, relay „REL
Fault” is activated.
Entering Fire condition of Control Panel
suppresses the messages of fault condition.
The display shows information about the type of
the fault and the total number of faults.
(Example: Fault in the Back up batteries supply.
Total number of faults –2. The common indicator
for fault condition is illuminated , the
specialized indicator and the local indicator
for fault conditionin zone 7.The second fault can
be reviewed by using buttons “Up” and “Down”).
8.3. Using the keypad
There are no active buttons in fatal fault condition.
For the other fault conditions are used 4 active buttons. When the Fire Control Panel is in a
combination with other conditions are active their corresponding buttons.
Button
Access
Level
Action
Additional information
Button
(“Alarm”)
All
Pressing the button:
- switches off the local
sounder;
- activates the local sounder,
if the Control Panel has
entered Fire or Fault
condition, and the local
sounder was switched off by
previous pressing of this
button.
The action of the button is
reversible i.e by single pressing
changes the current condition
respectively –switched off or
switched on sounder.
The LED indicator is
illuminated if the condition
switched off sounder is active.
The local sounder is
activated again:
- upon entering Fire
condition of the Control
Panel;
- in occurance of a new
fault or fire.
Buttons („Up”
and „Down”)
и
All
Display information about fault
conditions, if more than one fault is
registered.
Button
(“Menu”)
All
Pressing the button enters
Information and control.
Check the condition of the
fire detectors and the current fault
conditions.
9. Disabled component condition
9.1. Description
The Fire Control Panel enters Disabled component condition after manual operation of disabling
an element of the Fire alarm system –a fire detector or a routers (controller).
Operations for disabling shall be performed in Set Up mode at access level 2 or higher.
Upon disabling an output, it can not be activated in any circumstances and it is not monitored for
fault condition.
Operations on disabling elements are described in “Set Up” condition.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page19
Revision 10/02.17 Pages51
9.2. Indication
9.2.1. LED and sound indication
In presence of a disabled component, indicator is continuously on
The condition has no sound indication.
9.2.2. Text indication
The entered disabled components can be
reviewed from condition Information and control
of the Control Panel:
- upon selecting „Disabled Devices”the
disabled elements are visualized;
- General information about the number of
the disabled devices is provided in menu
„Status/Outputs”, „Status/Zones” and
„Status/ Panel”.
The position of the flashing cursor „█„ is displayed with highlighted first character of the chapter in
the menu.
9.3. Using the keypad
Button
Access
Level
Action
Additional information
Button
(“Menu”)
All
Pressing the button enters
condition information and control. All
the disabled components can be
reviewed from menu „Disabled
Devices”
Using the buttons in condition
Information and control is
described in details in chapter 11
and 12.
10. Test condition
10.1. Description
The Fire Control Panel eneters Test condition by a specific zone after manual operation for seting
a zone in test. The condition can be controlled from Information and control menus after entering a
password for access.
Enter menu „Status/Zones”to start the test.
10.2. Indication
10.2.1. LED and sound indication
The condition has no specific sound indication. LED and the LED indicator of the
corresponding zone in test are illuminated.
10.2.2. Text indication
In transition to menu Status/Zones a start test
window is displayed.
Enter access password.

UniPOS Wireless Fire Alarm Control Panel VIT 01
Instruction manual Page20
Revision 10/02.17 Pages51
The zone is set to Test mode.
The display shows information about:
- Zone number in test;
- Zone mode;
- Number of detectors in Fire condition;
- Number of Disabled components;
- Number of detectors in Fault condition.
Exit of the condition is to be performed by the
same way, as in the menu „Start Test” is changed
with „Stop Test”.
10.3. Using the keypad
Active buttons are:
-buttons and for zone selection and inserting the digits of the password;
-button to enter menu test and confirmation of the inserted password;
-button for exit.
11. Information and control condition
11.1. Description
Information and control condition mode, through the system of main menus and submenus,
provide opportunity to have information about the Control Panel’s settings and control some features
of the system components.
This condition can operate in combination with the following modes of the Control:
- Duty Mode;
- Fire Condition;
- Disabled component mode;
- Test mode;
- Fault condition mode;
- Set Up mode.
11.2. Indication
11.2.1. LED and sound indication
There is no specific LED or sound indication in the this condition of the panel.
11.2.2. Text indication
The screens, showing on the display are organized in tree structure of subordinated one to the
other menus (Appendix 2).
Each screen has a specific text indication, connected to the actions, performed in it. The specific
messages are described in the relevant screens.
11.3. Using the keypad
Press button to enter condition Information and control from the windows of Duty Mode, Fire
condition, Fault condition, Test and Disabled component, which suppresses their text messages.
When the Control Panel is in combination of Information and control and Fault condition, button
(“Alarm”) is also active.
When the Control Panel is in combination of Information and control and Fire condition, the active
buttons are (“Alarm”) and (“Outputs”).